Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Eric Jin <eric.jin@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13292 6f19259b-4bc3-4df7-8a09-765794883524
1. If string length exceeds 65535 bytes, return error. So infinite loop will not happen because of UINTN overflow.
2. When a SMBIOS entry is added or updated, check if the total length of SMBIOS table exceeds 65535 bytes, if it happens, return error.
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13290 6f19259b-4bc3-4df7-8a09-765794883524
0xb000 is the address normally used with QEMU.
0x400 also appears to conflict with some debug I/O ports
used by QEMU.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13279 6f19259b-4bc3-4df7-8a09-765794883524
If the bit is not set, then the only method ACPI defines
for setting it is to use the SMI SCI enable code path.
Since OVMF does not support SMM, we must enable the
bit during boot.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13278 6f19259b-4bc3-4df7-8a09-765794883524
OVMF does not support SMM. Previously the port value
was set to 0. This should be enough to disable the
SMM ACPI Enable/Disable code paths, but to be
consistent we'll set these fields to 0 as well.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13277 6f19259b-4bc3-4df7-8a09-765794883524
QEMU hard codes the GPE0 registers at 0xafe0.
Previously the code assumed that the GPE0 block
would move when the PM Base Address of the PIIX4
PCI device was programmed. It appears QEMU does not
emulate this behaviour of the PIIX4 PCI device.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13276 6f19259b-4bc3-4df7-8a09-765794883524
Since the System Memory initialization has been moved inside ArmPlatformSecLib
on some platforms, the use of this library could crash if the firmware engineer
forgot to initialize the DRAM.
This library 'patches' the DRAM to add an infinite loop.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13262 6f19259b-4bc3-4df7-8a09-765794883524
The function only used in Secure Firmware used to be mixed with
the Non-Secure/Normal functions in ArmPlatformLib.
When the Secure Firmware was not required for some platforms (eg:
BeagleBoard), these functions were empty functions.
This new interface has been created to clean the ArmPlatformLib
interface between the SEC and PEI phases.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13260 6f19259b-4bc3-4df7-8a09-765794883524
The function 'ArmGicAcknowledgeSgiFrom' was actually acknowledging Interrupts (and not only SGIs).
ArmPkg/ArmGicLib: Introduced the PCD PcdGicPrimaryCoreId
This PCD defines the Id of the primary core in the GIC.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13259 6f19259b-4bc3-4df7-8a09-765794883524
The 'NS' bit must only be set in Secure world to define the Non-Secure region
of the Non-Secure World.
This bit must not be set in Non-Secure World.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13252 6f19259b-4bc3-4df7-8a09-765794883524
Previsouly the synchronization of MpCore was using the SGI (Software
Generated Interrupt) to synchronize MpCore during the early boot.
This commit replaced this mechanism by the more appropriate SEV/WFE
instructions (Send/Wait Event instructions).
That also eases the port to a new cpu/platform.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13249 6f19259b-4bc3-4df7-8a09-765794883524
This function was introduced in some drivers to check if the ARM controller
was present in the memory map.
It was using a 8 bit access to get the value from the Identification registers.
These accesses could generate access error on some buses. Instead of replacing
the 8bit access by a 32bit access, these fcuntions have been removed because
they are only useful when the boot firmware is ported on a new platform.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13247 6f19259b-4bc3-4df7-8a09-765794883524
This function returns the address of a Global Variable in the Global Variable Region.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13246 6f19259b-4bc3-4df7-8a09-765794883524
- ArmPlatformNormalInitialize() has been renamed into ArmPlatformInitialize()
- Make the function be called at the early stage of the PEI phase as some
platforms require their interconnects or clocks to be initialize before any
access to Timers or UARTs.
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13245 6f19259b-4bc3-4df7-8a09-765794883524
SMM S3 resume may change memory cache type for flash memory range and thus RestoreS3PageTables() in which loops are executed to create page table would have negative performance impact on S3 resume. Move the call to RestoreS3PageTables() earlier before SMM S3 resume can avoid this issue.
Signed-off-by: Sun Rui <rui.sun@intel.com>
Reviewed-by: Yao Jiewen <jiewen.yao@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13231 6f19259b-4bc3-4df7-8a09-765794883524
niruiyu
lgao4
tye1
lzeng14
ydong10
jljusten
li-elvin
oliviermartin
erictian
rsun3