Putting DEBUG () code after an ASSERT (FALSE) statement is not very
useful, since the code will be unreachable on DEBUG builds and compiled
out on RELEASE builds. So move the ASSERT () statement after it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
On some platforms, performing cache maintenance on regions that are backed
by NOR flash result in SErrors. Since cache maintenance is unnecessary in
that case, create a PEIM specific version that only performs said cache
maintenance in its constructor if the module is shadowed in RAM. To avoid
performing the cache maintenance if the MMU code is not used to begin with,
check that explicitly in the constructor.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This implements the platform glue for the new generic BDS implementation.
It is based on the ArmVirtQemu version, with the QEMU references removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Instead of cleaning the data cache to the PoU by virtual address and
subsequently invalidating the entire I-cache, invalidate only the
range that we just cleaned. This way, we don't invalidate other
cachelines unnecessarily.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
When we split a block entry into a table entry, the UXN/PXN/XN permission
attributes are inherited both by the new table entry and by the new block
entries at the next level down. Unlike the NS bit, which only affects the
next level of lookup, the XN table bits supersede the permissions of the
final translation, and setting the permissions at multiple levels is not
only redundant, it also prevents us from lifting XN restrictions on a
subregion of the original block entry by simply clearing the appropriate
bits at the lowest level.
So drop the code that sets the UXN/PXN/XN bits on the table entries.
Reported-by: "Oliyil Kunnil, Vishal" <vishalo@qti.qualcomm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
DmaMap () only allows uncached mappings to be used for creating consistent
mappings with operation type MapOperationBusMasterCommonBuffer. However,
if the buffer passed to DmaMap () happens to be aligned to the CWG, there
is no need for a bounce buffer, and we perform the cache maintenance
directly without ever checking if the memory attributes of the buffer
adhere to the API.
So add some debug code that asserts that the operation type and the memory
attributes are consistent.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
In the DmaMap () operation, if the region to be mapped happens to be
aligned to the Cache Writeback Granule (CWG) (whose value is typically
64 or 128 bytes and 2 KB maximum), we remap the memory as uncached.
Since remapping memory occurs at page granularity, while the buffer and the
CWG may be much smaller, there is no telling what other memory we affect
by doing this, especially since the operation is not reverted in DmaUnmap().
So remove the remapping call.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
DmaMap () operations of type MapOperationBusMasterCommonBuffer should
return a mapping that is coherent between the CPU and the device. For
this reason, the API only allows DmaMap () to be called with this operation
type if the memory to be mapped was allocated by DmaAllocateBuffer (),
which in this implementation guarantees the coherency by using uncached
mappings on the CPU side.
This means that, if we encounter a cached mapping in DmaMap () with this
operation type, the code is either broken, or someone is violating the
API, but simply proceeding with a double buffer makes no sense at all,
and can only cause problems.
So instead, actively reject this operation type for cached memory mappings.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Comparing a GCD attribute field directly against EFI_MEMORY_UC and
EFI_MEMORY_WT is incorrect, since it may have other bits set as well
which are not related to the cacheability of the region. So instead,
test explicitly against the flags EFI_MEMORY_WB and EFI_MEMORY_WT,
which must be set if the region may be mapped with cacheable attributes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
We manage to use both an AND operation with 'gCacheAlignment - 1' and a
modulo operation with 'gCacheAlignment' in the same compound if statement.
Since gCacheAlignment is a global of which the compiler cannot guarantee
that it is a power of two, simply use the AND version in both cases.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The allocation function UncachedAllocatePages () may return NULL, in
which case our implementation of DmaAllocateBuffer () should return
EFI_OUT_OF_RESOURCES rather than silently ignoring the NULL value and
returning EFI_SUCCESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This adds a partial stack dump (256 bytes at either side of the stack
pointer) to the CPU state dumping routine that is invoked when taking an
unexpected exception. Since dereferencing the stack pointer may itself
fault, ensure that we don't enter the dumping routine recursively.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
The default exception handler, which is essentially the one that is invoked
for unexpected exceptions, ends with an ASSERT (FALSE), to ensure that
execution halts after dumping the CPU state. However, ASSERTs are compiled
out in RELEASE builds, and since we simply return to wherever the ELR is
pointing, we will not make any progress in case of synchronous aborts, and
the same exception will be taken again immediately, resulting in the string
'Exception at 0x....' to be printed over and over again.
So use an explicit deadloop instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
On ARM, manipulating live page tables is cumbersome since the architecture
mandates the use of break-before-make, i.e., replacing a block entry with
a table entry requires an intermediate step via an invalid entry, or TLB
conflicts may occur.
Since it is not generally feasible to decide in the page table manipulation
routines whether such an invalid entry will result in those routines
themselves to become unavailable, use a function that is callable with
the MMU off (i.e., a leaf function that does not access the stack) to
perform the change of a block entry into a table entry.
Note that the opposite should never occur, i.e., table entries are never
coalesced into block entries.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Now XN attribute will be set automatically if the region is declared
as device memory. However, the function ArmMemoryAttributeToPageAttribute
is to get attribute for block and page descriptors, not for table
descriptors, so attribute TT_TABLE_*XN does not really take effect.
Need to use TT_*XN_MASK instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Some minor typographical problems were noticed during previous commits.
This change corrects those, and contains no functional modifications.
The changes are in comments, and one diagnostic message.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The TimerFreq variable in the TimerConstructor() is unused in RELEASE
builds since ASSERTs are then disabled.
The only use of the variable (in the ASSERT) is replaced by a direct
invocation of the function previously used to set it.
NOTE: The build tools suppress warnings of this using compiler options
eg. -Wno-unused-but-set-variable for GCC toolchain or
--diag_suppress=550 for RVCT toolchain.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
FirmwarePerformanceDxe.c utilizes the Timer Library function
GetTimeInNanoSecond() which was not implemented by the ArmArchTimerLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This refactors some timer code to define MultU64xN as a preprocessor
symbol rather than a function pointer, and to factor out the code that
obtains the timer frequency into GetPlatformTimerFreq ().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
[ard.biesheuvel: split off from 'add GetTimeInNanoSecond() to ArmArchTimerLib']
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The function ArmClearMemoryRegionReadOnly() was supposed to undo the
effect of ArmSetMemoryRegionReadOnly(), but instead, it sets the permissions
to EL0-no access, EL1-read-only. Since the EL0 bit should be 1 to align
with EL2/3 (where the bit is SBO), use TT_AP_RW_RW instead, which makes the
entry read-write for EL0 when executing at EL1, and read-write for all other
levels.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This replaces the somewhat opaque preprocessor based stack/unstack macros
with open coded ldp/stp sequences to preserve the interrupted context
before handing over to the exception handler in C.
This removes various arithmetic operations on the stack pointer, and
reduces the exception return critical section to its minimum size (i.e.,
the bare minimum required to populate the ELR and SPSR registers and invoke
the eret).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
If we are using the vector table in place, there is no need to make an
indirect call to the common handler routine from the vector table entries,
so just use a straight branch instruction in that case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
The global gArmRelocateVectorTable is a build time constant, but due to
its external linkage and lack of constness, the compiler does not see that.
So turn it into a static boolean, and at the same time, make the function
CopyExceptionHandlers() (which is only called if gArmRelocateVectorTable is
set) static as well, so that the compiler can eliminate it completely if
we are using the vector table in place.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
ESR and FAR are populated by the hardware upon exception entry, and
describe the exception, not the interrupted context. So there is no point
in restoring their values before returning from the exception.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
We have three code paths to stack/unstack the exception context, one for
each of EL3, EL2 and EL1. However, they all access the same copy of FPSR
so move that access to the common path.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
Unlike the AArch32 vector table, which has room for a single instruction
for each exception type, the AArch64 exception table has 128 byte slots,
which can easily hold the shared prologues that are emitted out of line.
So refactor this code into a single macro, and expand it into each vector
table slot. Since the address of the command handler entry point is no
longer patched in by the C code, we can just emit the literal into each
vector entry directly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
Introduce ARM and AArch64 instances of the CpuExceptionHandlerLib which
provides exception handling and registration of handlers regardless of
execution phase.
Two variants of the ArmExceptionLib are provided: one where exception
handlers reside within the module (meeting appropriate architectural
alignment requirements for the vector table) and another one that will
relocate a copy of thee xception handlers to an address specified by
PcdCpuVectorBaseAddress. The ArmRelocateExceptionLib is intended for use
in cases where ArmExceptionLib is too large for the application
(uncompressed XIP images) as driven by the vector table alignment padding.
The AArch64 build of this library supports execution at EL1, EL2, and EL3
exception levels.
Tested on ARM, and AArch64 with SEC, DXE Core, and CpuDxe modules.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Add ArmReadHcr() to ArmLib to enable read-modify-write of the HCR system
register.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Architecturally, the TTBCR register value is undefined at reset for
Non-Secure.
On some platforms the reset value for TTBCR is not zero and
this causes a data abort exception once the MMU is enabled.
This patch configures the TTBCR register to enable translation table
walk using TTBR0.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
The AArch64 DAIF bits are different for reading (mrs) versus writing
(msr). The bitmask definitions assumed they were the same causing
incorrect results when trying to determine the current interrupt
state through ArmGetInterruptState.
The logic for interpreting the DAIF read data using the csel instruction
was also incorrect and is fixed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Modify the DefaultExceptionHandler (uefi-variant) so it can be used by
DxeCore (via CpuExceptionHandlerLib) where the debug info table is not
yet published at library constructor time.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Some updates to SCR can cause a problem which manifests as an undefined opcode exception.
This may be when a speculative secure instruction fetch happens after the NS bit is set.
An isb is required to make the register change take effect fully.
Contributed-under: Tianocore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <Evan.Lloyd@arm.com>
Reviewed-by: Sami Mujawar <Sami.Mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Problems have been encountered because some of the source files have
execute permission set. This can cause git to report them as changed
when they are checked out onto a file system with inherited permissions.
This has been seen using Cygwin, MinGW and PowerShell Git.
This patch makes no change to source file content, and only aims to
correct the file modes/permissions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19778 6f19259b-4bc3-4df7-8a09-765794883524
The RVCT compiler may emit calls to the various __aeabi_c?cmp??
functions, which return their results via the CPU condition flags
C and Z. According to ARM doc IHI 0043D 'Run-time ABI for the ARM
architecture':
The 3-way comparison functions c*cmple, c*cmpeq and c*rcmple return
their results in the CPSR Z and C flags. C is clear only if the operands
are ordered and the first operand is less than the second. Z is set only
when the operands are ordered and equal.
Add implementations for the double and float variants of the above.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19327 6f19259b-4bc3-4df7-8a09-765794883524
Commit SVN r18778 made all mappings of normal memory (inner) shareable,
even on hardware that implements shareability as uncached accesses.
The original concerns that prompted the change, regarding coherent DMA
and virt guests migrating between CPUs, do not apply to such hardware,
so revert to the original behavior in that case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19285 6f19259b-4bc3-4df7-8a09-765794883524
The -fno-tree-vrp option is not required for GCC 4.8 or later, and is not
supported by CLANG. So restrict its use to GCC 4.6 and 4.7, which are the
oldest versions we support for ARM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19283 6f19259b-4bc3-4df7-8a09-765794883524
The open coded access to co-processor #10 to set FPEXC is not supported
by the CLANG assembler, but the architecturally correct VMSR instruction
is not supported by older binutils. So keep the former unless __clang__
is defined.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19282 6f19259b-4bc3-4df7-8a09-765794883524
CLANG for ARM may emit calls to __aeabi_memset(), which is subtly different
from the default memset() [arguments 2 and 3 are reversed]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19281 6f19259b-4bc3-4df7-8a09-765794883524
The CLANG assembler does not support the legacy, non-unified assembler syntax,
i.e., it does not support the reordering of the condition suffixes with the
increment/decrement before/after or byte/word suffixes, and it does not
recognize the 'empty descending' (ED) suffix at all. So move to the unified
syntax, and replace 'empty descending' with 'decrement after' or 'increment
before' as appropriate.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19280 6f19259b-4bc3-4df7-8a09-765794883524
This patch updates the ArmPkg variant of InvalidateInstructionCacheRange to
flush the data cache only to the point of unification (PoU). This improves
performance and also allows invalidation in scenarios where it would be
inappropriate to flush to the point of coherency (like when executing code
from L2 configured as cache-as-ram).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Added AARCH64 and ARM/GCC implementations of the above.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19174 6f19259b-4bc3-4df7-8a09-765794883524
This has the effect of splitting assembly functions into their own sections
so the linker can remove unused ones to save space.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@gmail.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19109 6f19259b-4bc3-4df7-8a09-765794883524
In SVN 18756 ("disallow whole D-cache maintenance operations")
InvalidateInstructionCache was modified to remove the full data cache
clean but left the full instruction cache invalidate. The change was
made to address issues in the set/way clean methodology but the
resulting code could lead someone to a painful debug. If a component
called this function, the proper code would not be flushed to the PoU,
since the intent of this function is not only to invalidate the I-cache
but to provide coherency after code loading / modification. This change
simply places an ASSERT(FALSE) in this function to avoid this hazard.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19084 6f19259b-4bc3-4df7-8a09-765794883524
The ARM softfloat library in ArmSoftfloatLib currently does not build
under RVCT, simply because the code includes system header files that
RVCT does not provide. However, nothing exported by those include files
is actually used by the library when built in SOFTFLOAT_FOR_GCC mode,
so we can just drop all of them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19031 6f19259b-4bc3-4df7-8a09-765794883524
In order to support software floating point in the context of
DXE drivers etc, this factors out the core ARM softfloat support
into a separate library.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19030 6f19259b-4bc3-4df7-8a09-765794883524
The BdsLib implementation under ArmPkg never references
gArmGlobalVariableGuid so it should not list it as a dependency.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18997 6f19259b-4bc3-4df7-8a09-765794883524
As of SVN 15115, the PEI core needs a MigratePeiServicesTablePointer function.
Background: The ArmPkg variant of the PeiServicesTablePointerLib implements
the standard PEI Services table retrieval mechanism as defined in the
PI Specification Volume 1 section 5.4.4 using the TPIDRURW registers.
No special action is required on ARM to migrate the PEI Services table
pointer after main memory initialization but a function must be implemented
nonetheless.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18953 6f19259b-4bc3-4df7-8a09-765794883524
RVCT (the proprietary 32-bit ARM compiler) warns about Node potentially being
used uninitialized, so initialize it to NULL explicitly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18952 6f19259b-4bc3-4df7-8a09-765794883524
The way the v7 MMU code is invoked by the Xen port is somewhat of
a pathological case, since it describes its physical memory space
using a single cacheable region that covers the entire addressable
range. When clipping this region to the part that is 1:1 addressable,
we end up with a region of exactly 4 GB in size, which just exceeds
the range of the UINT32 variable we use in FillTranslationTable() to
track our progress while populating the page tables. So promote it
to UINT64 instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18930 6f19259b-4bc3-4df7-8a09-765794883524
It is implied that the memory returned from UncachedMemoryAllocationLib
should have cache invalidated. So we invalidate memory range after
changing memory attribute to uncached.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18920 6f19259b-4bc3-4df7-8a09-765794883524
In ArmLib, there exists an alias for ArmDataSynchronizationBarrier,
named after one of several names for the pre-ARMv6 cp15 operation that
was formalised into the Data Synchronization Barrier in ARMv6.
This alias is also the one called from within ArmLib, in preference of
the correct name. Through the power of code reuse, this name slipped
into the AArch64 variant as well.
Expunge it from the codebase.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18915 6f19259b-4bc3-4df7-8a09-765794883524
We currently rely on .align directives to ensure that each exception
vector entry is the appropriate offset from the vector base address.
This is slightly fragile, as were an entry to become too large (greater
than 32 A64 instructions), all following entries would be silently
shifted until they meet the next alignment boundary. Thus we might
execute the wrong code in response to an exception.
To prevent this, introduce a new macro, VECTOR_ENTRY, that uses .org
directives to position each entry at the precise required offset from
the base of a vector. A vector entry which is too large will trigger a
build failure rather than a runtime failure which is difficult to debug.
For consistency, the base and end of each vector is similarly annotated,
with VECTOR_BASE and VECTOR_END, which provide the necessary alignment
and symbol exports. The now redundant directives and labels are removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18904 6f19259b-4bc3-4df7-8a09-765794883524
As EDK2 runs in an idmap, we do not use TTBR1_EL1, nor do we configure
it. TTBR1_EL1 may contain UNKNOWN values if it is not programmed since
reset.
Prior to enabling the MMU, we do not set TCR_EL1.EPD1, and hence the CPU
may make page table walks via TTBR1_EL1 at any time, potentially using
UNKNOWN values. This can result in a number of potential problems (e.g.
the CPU may load from MMIO registers as part of a page table walk).
Additionally, in the presence of Cortex-A57 erratum #822227, we must
program TCR_EL1.TG1 == 0b1x (e.g. 4KB granule) regardless of the value
of TCR_EL1.EPD1, to ensure that EDK2 can make forward progress under a
hypervisor which makes use of PAR_EL1.
This patch ensures that we program TCR_EL1.EPD1 and TCR_EL1.TG1 as above
to avoid these issues. TCR_EL1.TG1 is set to 4K for all targets, as any
CPU capable of running EDK2 must support this granule, and given
TCR_EL1.EPD1, programming the field is not detrimental in the absence of
the erratum.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18903 6f19259b-4bc3-4df7-8a09-765794883524
The ARM_MEMORY_REGION_DESCRIPTOR array provided by the platform may
contain entries that extend beyond the 4 GB boundary, above which
we can't map anything on 32-bit ARM. If this is the case, map only
the 1:1 addressable part.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18900 6f19259b-4bc3-4df7-8a09-765794883524
Bits 0 and 6 of the TTBRx system registers have different meanings
depending on whether a system implements the Multiprocessing
Extensions. So use separate memory attribute definitions for MP and
non-MP.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18899 6f19259b-4bc3-4df7-8a09-765794883524
Even though mapping normal memory (inner) shareable is usually the
correct choice on coherent systems, it may be desirable in some cases
to use non-shareable mappings for normal memory, e.g., when hardware
managed coherency is not required and the memory system is not fully
configured yet. So introduce a PCD PcdNormalMemoryNonshareableOverride
that makes cacheable mappings of normal memory non-shareable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18897 6f19259b-4bc3-4df7-8a09-765794883524
To align with the way normal cacheable memory is mapped, set the
shareable bit for cached accesses performed by the page table walker.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18896 6f19259b-4bc3-4df7-8a09-765794883524
Some MMU manipulation is dependent on the presence of the multiprocessing
extensions. So add a function that returns this information.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18895 6f19259b-4bc3-4df7-8a09-765794883524
Implement an accessor function for the ID_MMFR0 system register, which
contains information about the VMSA implementation. We will need this
to access the number of shareability levels and the nature of their
implementations.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18894 6f19259b-4bc3-4df7-8a09-765794883524
The definition TTBR_WRITE_THROUGH_NO_ALLOC makes little sense, since
a) its meaning is unclear in the context of TTBRx, since write through
always implies Read-Allocate and no Write-Allocate
b) its definition equals the definition of TTBR_WRITE_BACK_ALLOC
So instead, rename it to TTBR_WRITE_THROUGH and update the definition
to reflect the name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18893 6f19259b-4bc3-4df7-8a09-765794883524
To prevent speculative intruction fetches from MMIO ranges that may
have side effects on reads, the architecture requires device mappings
to be created with the XN or UXN/PXN bits set (for the ARM/EL2 and
EL1&0 translation regimes, respectively.)
Note that, in the ARM case, this involves moving all accesses to a
client domain since permission attributes like XN are ignored from
a manager domain. The use of a client domain is actually mandated
explicitly by the UEFI spec.
Reported-by: Heyi Guo <heyi.guo@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18891 6f19259b-4bc3-4df7-8a09-765794883524
The function GcdAttributeToArmAttribute() is not used anywhere in the
code base, and is only defined for AARCH64 and not for ARM. It also
fails to set the bits for shareability and non-executability that we
require for correct operation. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18888 6f19259b-4bc3-4df7-8a09-765794883524
We force alignment to 2K after generating the DebugAgentVectorTable
symbol, and hence DebugAgentVectorTable itself may not be 2K-aligned,
and table entries may not be at the correct offset from the
DebugAgentVectorTable base address.
Fix this by forcing alignment before generating the
DebugAgentVectorTable symbol.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18865 6f19259b-4bc3-4df7-8a09-765794883524
Mark all cached memory mappings as shareable (or inner shareable on
AArch64) so that our view of memory is kept coherent by the hardware.
This is relevant for things like coherent DMA and virtualization (where
a guest may migrate to another core) but in general, since UEFI on ARM
is mostly used in a context where the secure firmware and possibly a
secure OS are already up and running, it is best to refrain from using
any non-shareable mappings.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18778 6f19259b-4bc3-4df7-8a09-765794883524
When allocating memory to perform non-coherent DMA, use the cache
writeback granule rather than the data cache linesize for alignment.
This prevents the explicit cache maintenance from corrupting
unrelated adjacent data if the cache writeback granule exceeds
the cache linesize.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18759 6f19259b-4bc3-4df7-8a09-765794883524
Add a function to ArmLib that provides access to the Cache Writeback
Granule (CWG) field in CTR_EL0. This information is required when
performing non-coherent DMA.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18758 6f19259b-4bc3-4df7-8a09-765794883524
The ARM architecture provides no reliable way to clean or invalidate
the entire data cache at runtime. The reason is that such maintenance
requires the use of set/way maintenance operations, which are suitable
only for the kind of maintenance that is carried out when the cache is
taken offline entirely.
So ASSERT () when any of the CacheMaintenanceLib whole data cache routines
are invoked rather than pretending we can do anything meaningful here.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18756 6f19259b-4bc3-4df7-8a09-765794883524
There is no need to issue a full data synchronization barrier and an
instruction synchronization barrier after each and every set/way or
MVA cache maintenance operation. For the set/way case, we can simply
remove them, since the set/way outer loop already issues the required
barriers after completing its traversal over all the cache levels.
For the MVA case, move the data synchronization barrier out of the
loop, and add the instruction synchronization barrier to the I-cache
invalidation by MVA routine.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18755 6f19259b-4bc3-4df7-8a09-765794883524
The stride used by the cache maintenance by MVA instructions should
be retrieved from CTR_EL0.DminLine and CTR_EL0.IminLine, whose values
reflect the actual geometry of the caches. Using CCSIDR for this purpose
violates the architecture.
Also, move the line length accessors to common code, since there is no
need to keep them separate between ARMv7 and AArch64.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18754 6f19259b-4bc3-4df7-8a09-765794883524
The ARM architecture does not allow the actual geometries of the caches
to be inferred from the CCSIDR cache info system register, since the
geometry it reports is intended for performing cache maintenance by
set/way and nothing else. Since the ArmLib cache info routines are
based solely on CCSIDR contents, they should not be used.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18753 6f19259b-4bc3-4df7-8a09-765794883524
The function ArmCleanDataCacheToPoU() has no users, and its purpose
is unclear, since it uses cache maintenance by set/way to perform
the clean to PoU, which is a dubious practice to begin with. So
remove the declaration and all definitions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18752 6f19259b-4bc3-4df7-8a09-765794883524
The ARM9 ArmLib implementation is not referenced anywhere in the
tree, and unlikely to be useful going forward, considering that
ARM9 outdates even ARMv6. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18750 6f19259b-4bc3-4df7-8a09-765794883524
The ARM architecture requires a DSB to complete TLB maintenance, with a
subsequent ISB being required to synchronize subsequent items in the
current instruction stream against the completed TLB maintenance.
The ArmEnableMmu function is currently missing the DSB, and hence the
TLB maintenance is not guaranteed to have completed at the point the MMU
is enabled. This may result in unpredictable behaviour.
The DSB subsequent to the write to SCTLR_EL1 is unnecessary; the ISB
alone is sufficient to complete all prior instructions and to
synchronise the new context with any subsequent instructions.
This patch adds missing DSBs to complete TLB maintenance, and removes
the unnecessary trailing DSB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18749 6f19259b-4bc3-4df7-8a09-765794883524
When performing a tftp download from a server which does not support
rfc2349 transfer size option (such as netkit-tftpd), the existing code
falls back to allocating an 8MB buffer. Since this is insufficient for
an uncompressed AArch64 Linux kernel image, double the size to 16MB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ashutosh Singh <ashutosh.singh@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18748 6f19259b-4bc3-4df7-8a09-765794883524
Use the refactored UpdateRegionMapping () to traverse the translation
tables, splitting block entries along the way if required, and apply
a mask + or on each to set or clear the PXN/UXN/XN or RO bits.
For now, the 32-bit ARM versions remain unimplemented.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18587 6f19259b-4bc3-4df7-8a09-765794883524
Move the page table traversal and splitting logic to a separate function
UpdateRegionMapping() and refactor it slightly so we can reuse it later to
implement non-executable regions, for the stack. This primarly involves
adding a value/mask pair to the function prototype that allows us to flip
arbitrary bits on each block entry as the page tables are traversed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18586 6f19259b-4bc3-4df7-8a09-765794883524
The non-privileged execute never (UXN) page table bit defined for the
EL1&0 translation regime and the execute never (XN) bit defined for the
EL2 and EL3 translation regimes happen to share the same bit position,
but they are in fact defined distinctly by the architecture. So define
both bits explicitly, and add comments in places where we take advantage
of the fact that they share the same bit position.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18585 6f19259b-4bc3-4df7-8a09-765794883524
All our page tables are allocated from memory whose cacheability
attributes are inherited by the cacheability bits in the MMU control
register, so there is no need for explicit cache maintenance after
updating the page tables. And even if there were, Set/Way operations
are not appropriate anyway for ensuring that these changes make it to
main memory. So just remove the explicit cache maintenance completely.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18570 6f19259b-4bc3-4df7-8a09-765794883524
Now that the AArch64 MMU code correctly identifies and handles
naturally aligned regions of more than 2 MB in size, it will happily
try to use block mappings at level 0 to map huge memory regions, such
as the single cacheable 1:1 mapping we use for Xen domU to map the
entire PA space. However, block mappings are not supported at level 0
so the resulting translation tables will be incorrect, causing
execution to fail as soon as the MMU is enabled.
So use level 1 as the minimum level at which to perform block
translations.
Reported-by: Julien Grall <julien.grall@citrix.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18568 6f19259b-4bc3-4df7-8a09-765794883524
During page entry attribute update, if there are table entries
between starting BlockEntry and LastBlockEntry, table entries will be
set as block entries and the allocated memory of the tables will be
leaked.
So instead, we break the inner loop when we find a table entry and run
outer loop again to step into the table by the same logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
[ardb: move termination condition check inside the loop]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18425 6f19259b-4bc3-4df7-8a09-765794883524
Below code has bug since *BlockEntrySize and *TableLevel are not
updated accordingly:
if (IndexLevel == PageLevel) {
// And get the appropriate BlockEntry at the next level
BlockEntry = (UINT64*)TT_GET_ENTRY_FOR_ADDRESS (TranslationTable, \
IndexLevel + 1, RegionStart);
// Set the last block for this new table
*LastBlockEntry = TT_LAST_BLOCK_ADDRESS(TranslationTable, \
TT_ENTRY_COUNT);
}
Also it doesn't check recursively to get the last level, e.g. the
initial PageLevel is 1 and we already have level 2 and 3 tables at
this address.
What's more, *LastBlockEntry was not updated when we get a table and
IndexLevel != PageLevel.
So we reorganize the sequence, only updating TranslationTable,
PageLevel and BlockEntry in the loop, and setting the other output
parameters with the final PageLevel before returning.
And LastBlockEntry is only an OUT parameter.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18424 6f19259b-4bc3-4df7-8a09-765794883524
There is a hidden bug for below code:
(1 << BaseAddressAlignment) & *BlockEntrySize
From disassembly code, we can see the literal number 1 will be treated
as INT32 by compiler by default, and we'll get 0xFFFFFFFF80000000 when
BaseAddressAlignment is equal to 31. So we will always get 31 when
alignment is larger than 31.
if ((1 << BaseAddressAlignment) & *BlockEntrySize) {
5224: f9404be0 ldr x0, [sp,#144]
5228: 2a0003e1 mov w1, w0
522c: 52800020 mov w0, #0x1 // #1
5230: 1ac12000 lsl w0, w0, w1
5234: 93407c01 sxtw x1, w0
The bug can be replayed on QEMU AARCH64; by adding some debug print,
we can see lots of level 1 tables created (for block of 1GB) even
when the region is large enough to use 512GB block size.
Use LowBitSet64() in BaseLib instead to fix the bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18423 6f19259b-4bc3-4df7-8a09-765794883524
The bug can be triggered when alignment of Base is larger than Length
by 2 level of page granularity, e.g.
Base is 0x4000_0000, Length is 0x1000
The original code will change 2MB page level and we will get a
negative remaining length.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18422 6f19259b-4bc3-4df7-8a09-765794883524
The code has a simple bug on calculating aligned page table address.
We can just use AllocateAlignedPages in MemoryAllocationLib instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18421 6f19259b-4bc3-4df7-8a09-765794883524
NewNode is the node we found, while Node is the last node in the
list. Also update mFreedBufferSize.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18390 6f19259b-4bc3-4df7-8a09-765794883524
No platforms use the ARMv6 (ARM11) support code anymore. In fact, the
only reference to it in ArmPkg.dsc was commented out by Andrew in SVN
r11298 (2011-02-03) so it may well be broken. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18237 6f19259b-4bc3-4df7-8a09-765794883524
Instead of inferring the GIC revision from the CPU id registers
and the presence/availability of the system register interface
upon each invocation, move the logic to a constructor and cache
the result.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18100 6f19259b-4bc3-4df7-8a09-765794883524
Clone ArmGicArchLib into a SEC phase specific ArmGicArchSecLib
so that we can modify the former in a subsequent patch to cache
the GIC revision in a global variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18099 6f19259b-4bc3-4df7-8a09-765794883524
The current implementation of ArmGicGetSupportedArchRevision ()
that is used by all ARM platforms is entirely stateless (in order
to support being executed from flash) so it needs to interrogate
the hardware for the supported GIC revision upon each invocation.
However, this statelessness is only needed for SEC type modules;
in all other cases, we could easily determine the GIC revision once,
and store the result in a global variable.
In preparation of having separate early and normal versions, this patch
introduces the ArmGicArchLib library class and default implementation,
and moves the existing ArmGicGetSupportedArchRevision () into it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18098 6f19259b-4bc3-4df7-8a09-765794883524
This change removes the embedded Linux Loder from BdsLib.
BdsLib becomes OS agnostic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17969 6f19259b-4bc3-4df7-8a09-765794883524
Replaced the function BdsLoadApplication() by two explicit
functions that load the EFI application either by its GUID
or its Name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17966 6f19259b-4bc3-4df7-8a09-765794883524
The TFTP Device Path might contain a list of File Path device
path nodes.
ConvertDevicePathToText() allows to concatenate these File Path
nodes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17539 6f19259b-4bc3-4df7-8a09-765794883524
We need to use msr instruction to write system register. It seems the
code was simply copied from ArmReadCntkCtl.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17440 6f19259b-4bc3-4df7-8a09-765794883524
Since there is now a formal definition of EFI_LOAD_OPTION, we can no
longer typedef it as a UINT8*. So update the code to use the common
definition, which is not a pointer type, hence the additional changes
to the C code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17410 6f19259b-4bc3-4df7-8a09-765794883524
Ard Biesheuvel
Heyi Guo
Evan Lloyd
Sami Mujawar
Leendert van Doorn
Cohen, Eugene
Leif Lindholm
Mark Rutland
Ashutosh Singh
Olivier Martin