We currently rely on .align directives to ensure that each exception
vector entry is the appropriate offset from the vector base address.
This is slightly fragile, as were an entry to become too large (greater
than 32 A64 instructions), all following entries would be silently
shifted until they meet the next alignment boundary. Thus we might
execute the wrong code in response to an exception.
To prevent this, introduce a new macro, VECTOR_ENTRY, that uses .org
directives to position each entry at the precise required offset from
the base of a vector. A vector entry which is too large will trigger a
build failure rather than a runtime failure which is difficult to debug.
For consistency, the base and end of each vector is similarly annotated,
with VECTOR_BASE and VECTOR_END, which provide the necessary alignment
and symbol exports. The now redundant directives and labels are removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18904 6f19259b-4bc3-4df7-8a09-765794883524
In ArmPkg/Include/Chipset, several CPU-specific header files reside.
Most of these provide no actual, or very little, use.
ARM1176JZ-S.h is not used at all (and unusable since SVN r18237).
ArmAemV8.h simply includes AArch64.h.
ArmCortexA15.h defines one processor-specific configuration bit and
then includes ArmV7.h.
Delete these include files, and update their sole users to function
without them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18736 6f19259b-4bc3-4df7-8a09-765794883524
Interrupt must be disabled before we storing ELR and other system
registers, or else ELR will be overridden by interrupt reentrance.
This bug is critical as we may get occasional exception or dead loop
when interrupt reentrance occurs:
After increasing SP ... Before popping out registers
Or
After restoring ELR
The 1st circumstance could also be resolved by optimizing SP operation
(Pop out registers before adding SP back), but the 2nd could not be
resolved by disabling interrupt.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18538 6f19259b-4bc3-4df7-8a09-765794883524
No platforms use the ARMv6 (ARM11) support code anymore. In fact, the
only reference to it in ArmPkg.dsc was commented out by Andrew in SVN
r11298 (2011-02-03) so it may well be broken. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18237 6f19259b-4bc3-4df7-8a09-765794883524
Use an explicit VOID* cast when passing a static char array into
a function taking a void pointer.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18193 6f19259b-4bc3-4df7-8a09-765794883524
The GNU assembler extends the generic notation for IMPLEMENTATION
DEFINED system registers to support any system register, so that
system registers defined by newer versions of the architecture can
still be used by older versions of the toolchain.
Clang before v3.6 supports the generic notation, but does not
support this extension, nor does it need to in the particular case
of the GICv3 support code, since it knows the GICv3 registers by
their architectural names. So only redefine their real names to
their generic aliases if we are not using clang.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18192 6f19259b-4bc3-4df7-8a09-765794883524
The current implementation of ArmGicGetSupportedArchRevision ()
that is used by all ARM platforms is entirely stateless (in order
to support being executed from flash) so it needs to interrogate
the hardware for the supported GIC revision upon each invocation.
However, this statelessness is only needed for SEC type modules;
in all other cases, we could easily determine the GIC revision once,
and store the result in a global variable.
In preparation of having separate early and normal versions, this patch
introduces the ArmGicArchLib library class and default implementation,
and moves the existing ArmGicGetSupportedArchRevision () into it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18098 6f19259b-4bc3-4df7-8a09-765794883524
Before splitting off ArmGicArchLib and moving it out of
ArmPkg/Drivers/ArmGic into ArmPkg/Library, make sure that the
GIC specific declarations it depends on are not hidden away in
local headers "GicV2/GicV2Lib.h" and "GicV3/GicV3Lib.h".
So merge them with <Library/ArmGicLib.h>. This is entirely
appropriate, since this is not a header that declares a public
interface into ArmGicLib, but defines implementation internals.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18097 6f19259b-4bc3-4df7-8a09-765794883524
When the function that determines the size of a contiguous region
was returning from a sub-level table scanning it was forgetting to
move to the next entry of its own level table.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17832 6f19259b-4bc3-4df7-8a09-765794883524
Accesses to system registers are disproportionately heavy-weight
when executed under virtualization, since each one involves two
world switches (from guest to host and back again).
So change the sequence that enables the GIC SRE interface so that
it performs only a single sysreg read to test whether the SRE
interface is enabled already, and only performs a write and an
additional read if that turns out not to be the case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17596 6f19259b-4bc3-4df7-8a09-765794883524
The DT binding for the ARM generic timer describes the secure,
non-secure, virtual and hypervisor timer interrupts, respectively.
However, under virtualization, only the virtual timer is usable, and
the device tree may omit the hypervisor timer interrupt. (Other timer
interrupts cannot be omitted simply due to the fact that the virtual
timer is listed third)
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16953 6f19259b-4bc3-4df7-8a09-765794883524
- GIC distributor needs to be programmed to target interrupts
on the boot CPU using the Interrupt Processor Targets Registers
- Enabling the GIC Distributor is different following the value
of GICD_CTLR.ARE_NS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16926 6f19259b-4bc3-4df7-8a09-765794883524
The GICv3 driver must use native mode to drive a GICv3 due to
the fact that v2 compatibility is optional in the v3 spec.
However, if v2 compatibility is implemented, it is the default
and needs to be disabled first by setting the Affinity Routing
Enable (ARE) bit.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
[added PCD that allows forcing the GICv3 driver to drive the GIC in v2 mode]
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16875 6f19259b-4bc3-4df7-8a09-765794883524
GICv3 controller with no GICv2 legacy support must use the GIC
Redistributor registers instead of the GIC Distributor registers
for some operations (eg: enable/disable interrupts).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16874 6f19259b-4bc3-4df7-8a09-765794883524
CPU GIC Registributors are located next to each other in the GIC Redistributor
space.
The CPU GIC Redistributor is identified by its CPU affinity Aff3.Aff2.Aff1.Aff0.
This function returns the base address of the GIC Redistributor of
the calling CPU.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16873 6f19259b-4bc3-4df7-8a09-765794883524
ARM GICv3 specification introduces some new components and registers.
This patch adds their definitions.
The most important GICv3 component is the GIC Redistributor. It supports
LPIs (Locality-specific peripheral Interrupt), 8+ CPU configuration.
Some GIC distributor registers have moved to the GIC redistributor.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16872 6f19259b-4bc3-4df7-8a09-765794883524
Use the system counter to compute the watchdog compare
value as the watchdog compare value is compared to the
system counter to check if the watchdog timeout expired or not.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16513 6f19259b-4bc3-4df7-8a09-765794883524
Even if the CPU id registers indicate hardware support for the
System Register interface to the GIC, higher exception levels
may disable that interface and only allow access through MMIO.
So move the enabling of the SRE bit to the GIC version detection
routine: if we trigger an exception, we would have anyway at a
later stage, so the net effect is the same. However, if setting
the bit doesn't stick, it means we can switch to MMIO and proceed
normally otherwise.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16344 6f19259b-4bc3-4df7-8a09-765794883524
This function returns the revision of the GIC Architecture.
Some GICv3 controllers can work in GICv2 mode. Switching to an
older GIC revision is driven by the higher level exception level.
This function allows code to support any GIC revision at runtime.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16231 6f19259b-4bc3-4df7-8a09-765794883524
KVM on ARM currently masks the timer interrupt on the timer side when
delivering an interrupt to the guest. This itself is a workaround for an
issue where the interrupt is reraised and trapped by the host as soon as
the guest is entered, resulting in the guest being starved.
Work around this by calling ArmGenericTimerEnable () after servicing each
interrupt. The virtual version of ArmGenericTimerCounterLib will then
make sure to unmask the interrupt again.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16144 6f19259b-4bc3-4df7-8a09-765794883524
The PCD gArmTokenSpaceGuid.PcdArmArchTimerFreqInHz is used in the
SEC phase (if applicable) to write the platform's counter frequency
to the CNTFRQ system register, as this needs to be done by the highest
exception level implemented.
Under virtualization, we should be able to rely on the host to have
initialized this register to a sane value, as we run at EL1 and only
use the virtual timer, so the PcdArmArchTimerFreqInHz PCD has little
meaning here.
So in either case, by the time we enter the DXE phase, we can use the
CNTFRQ system register to read the frequency instead of looking at the
PCD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16090 6f19259b-4bc3-4df7-8a09-765794883524
Move TimerDxe and ArmArchTimerLib to ArmGenericTimerCounterLib, and update all
platforms to select the physical counter instance they have been using
implicitly all along.
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16078 6f19259b-4bc3-4df7-8a09-765794883524
The ArmArchTimerLib.h include file is not directly related to the TimerLib
instance ArmArchTimerLib, so the name is confusing. Rename to ArmArchTimer.h
instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16073 6f19259b-4bc3-4df7-8a09-765794883524
Allow the PCDs gArmTokenSpaceGuid.PcdGicDistributorBase and
gArmTokenSpaceGuid.PcdGicInterruptInterfaceBase to be redeclared
as PcdsDynamic by the platform, so virtual machines can set these
properties during boot. As the PcdGet32() calls now call into the
PCD database, cache the values that are required during the handling
of interrupts.
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16072 6f19259b-4bc3-4df7-8a09-765794883524
This PCD has been replaced by ArmPlatformIsPrimaryCore() function.
Althrough this PCD is still used in some occasions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16026 6f19259b-4bc3-4df7-8a09-765794883524
Prior to this change, the TimerPeriod was re-initialize at the
end of the interrupt handling with the value of the period.
It means the real timer period was: Timer Interrupt Processing
time + Timer Period
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15923 6f19259b-4bc3-4df7-8a09-765794883524
Prior to this change the period was restored to the default period.
This change restores the latest 'set period'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15922 6f19259b-4bc3-4df7-8a09-765794883524
Prior to this change the frequency was rounded to 1Mhz.
This change rounds the timer frequency to 1KHz.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15921 6f19259b-4bc3-4df7-8a09-765794883524
The AArch64 Vector Table must be aligned on a 2K boundary.
The FDF specification does not support 2K alignment but support 4K.
A clear comment has been added to help integrator to understand why the
assertion fails when porting to a new AArch64 platform.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15659 6f19259b-4bc3-4df7-8a09-765794883524
The InterruptId has a different width for GicV2 and GicV3 (respectively
10bit and 24bit).
The function prototype has been changed to return this value to make the
caller GIC architecture version independent. Otherwise, we would have need
to expose a different mask to allow the caller to retrieve this value from
the read register.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15628 6f19259b-4bc3-4df7-8a09-765794883524
The support for GIcV2 was already existing. This change separate the GicV2
specific functions from the common Gic code (in preparation for GicV3 support).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15626 6f19259b-4bc3-4df7-8a09-765794883524
The implementation is the same when we run in Secure or Non-Secure world.
This change makes this function available for ArmGicSec.inf and ArmGicNonSec.inf.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15625 6f19259b-4bc3-4df7-8a09-765794883524
It will allow reusing the same code for GICv2 and GICv3 only drivers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15623 6f19259b-4bc3-4df7-8a09-765794883524
... and also rename the ArmGicLib sources to use an explicit 'Lib' suffix.
The renaming did not work well with SVN. Files were missing from the initial commit.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15622 6f19259b-4bc3-4df7-8a09-765794883524
... and also rename the ArmGicLib sources to use an explicit 'Lib' suffix.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15620 6f19259b-4bc3-4df7-8a09-765794883524
The function should detect and return the error in non-debug builds when the ASSERT does nothing.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15606 6f19259b-4bc3-4df7-8a09-765794883524
Mark Rutland
Leif Lindholm
Heyi Guo
Ard Biesheuvel
Olivier Martin
Ronald Cron