In the original code, there exists some mismatches between the real
waiting time and the corresponding timeout comments. For example, the
XHC_GENERIC_TIMEOUT comment says it's 10ms timeout value, but the real
code in fact waits 10s.
So the code is refined to be consistent in code logic and comments.
Note XHC_POLL_DELAY macro also be removed and the polling interval in
XhcWaitOpRegBit() is changed from 1ms to 1us to keep same code style
with other code. It has no real functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18235 6f19259b-4bc3-4df7-8a09-765794883524
EDKII usb stack is using a TPL_CALLBACK timer to monitor async transfer
request and signal event if it's done. As usb enumeration and usb mass
storage block i/o read/write runs on TPL_CALLBACK and TPL_NOTIFY level
respectively, It blocks usb async transfer requests, usually usb mouse
/use kb, getting time to run.
Without this change, user couldn't get usb mouse/kb state in time (will
show a little lag from UI view) when there is other usb transactions, such
as a new usb device inserted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18169 6f19259b-4bc3-4df7-8a09-765794883524
According to the PCI spec, when software writes all-one to BAR for size probing,
the value read back should be 0b1...10...0 after masking the BAR type bits.
But in real world, it's possible that certain device returns 0b0...01...10...0
for MEM64 BAR size probing: some bits in the high 32bit may be 0.
PciBus driver has the code to handle such case. However, it doesn't handle the
case that the high 32bit is totally 0. The patch is to handle the special case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18114 6f19259b-4bc3-4df7-8a09-765794883524
The logic in an if statement in PciIo is too complex and hard to understand
and make VS2015 build failure. The fix simplifies the logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18109 6f19259b-4bc3-4df7-8a09-765794883524
GLOBAL_REMOVE_IF_UNREFERENCED means __declspec(selectany) for MS tool
chain IA32/X64 build.
According to MSDN, "selectany" would tell the compiler that the declared
global data item (variable or object) is a pick-any COMDAT (a packaged
function). At link time, if multiple definitions of a COMDAT are seen,
the linker picks one and discards the rest.
So we have to remove GLOBAL_REMOVE_IF_UNREFERENCED key word from two global
variable's extern definitions of .h file as we have used this keyword in
.c file, otherwise the MS tool chain would pick the definitions in .h file
and treat it as uninitialized data to generate full-0 content for these two
global variables.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18088 6f19259b-4bc3-4df7-8a09-765794883524
The TPer Reset operation would be moved into SecurityPkg/Tcg/
MemoryOverwriteControl/TcgMor.inf module and be triggered at EndOfDxe.
By this way, all encrypted drives which produce EFI_STORAGE_SECURITY_
RPOTOCOL interface would be force reset when MOR is set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17717 6f19259b-4bc3-4df7-8a09-765794883524
Produce this protocol for each namespace at NVMe controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17638 6f19259b-4bc3-4df7-8a09-765794883524
Open NVM_EXPRESS_PASS_THRU rather than PCI_IO to create parent-child
relationship.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17636 6f19259b-4bc3-4df7-8a09-765794883524
The initialization of Cc.Iosqes and Cc.Iocqes should not be removed
before any I/O operation as it would impact Qemu-NVMe functionality
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17559 6f19259b-4bc3-4df7-8a09-765794883524
Follow IDE BUS Master spec to ensure the PRDT table not cross 64k
boundary in memory.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17552 6f19259b-4bc3-4df7-8a09-765794883524
LocatePciExpressCapabilityRegBlock () doesn't check the return status of Pci.Read().
Certain platform's PciRootBridge.Pci.Read() doesn't support PCIE access causing the CapabilityEntry not updated.
If the uninitialized CapabilityEntry equals to a big enough initial value, the while-loop will never end.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17513 6f19259b-4bc3-4df7-8a09-765794883524
A previous incorrect check-in adds the IsaBusDxe driver to <Root>/Bus directory.
The patch fixes it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17506 6f19259b-4bc3-4df7-8a09-765794883524
The original code hard-codes block size to 512. But after ATA 7 spec,
the non-512 block size is also supported. The code is updated to
dynamically calculate the block size according to IDENTIFY data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17495 6f19259b-4bc3-4df7-8a09-765794883524
It's to follow the PI spec 1.4.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jie Lin <jie.lin@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17367 6f19259b-4bc3-4df7-8a09-765794883524
This patch produces a EFI_NVM_EXPRESS_PASS_THRU protocol instance
on device handle to provide upper user a way to send cmd to NVMe
device.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17286 6f19259b-4bc3-4df7-8a09-765794883524
The changes in ScsiDisk include:
1. Add UFS disk info support.
2. Remove the wrong block size calculation.
3. Get sense data for TEST_UNIT_READY cmd immediately rather than sending a REQUEST_SENSE cmd again.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17247 6f19259b-4bc3-4df7-8a09-765794883524
It includes 4 drivers:
1. UfsPassThruDxe, which is a UEFI driver and consumes EFI_UFS_HOST_CONTROLLER_PROTOCOL and produces EFI_EXT_SCSI_PASS_THRU_PROTOCOL
2. UfsPciHcDxe, which is specific for pci-based UFS HC implementation and is a UEFI driver to produce EFI_UFS_HOST_CONTROLLER_PROTOCOL.
3. UfsBlockIoPei, which is a PEI driver and consumes EFI_UFS_HOST_CONTROLLER_PPI and produces EFI_PEI_VIRTUAL_BLOCK_IO_PPI.
4. UfsPciHcPei, which is specific for pci-based UFS HC implementation and is a PEI driver to produce EFI_UFS_HOST_CONTROLLER_PPI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17246 6f19259b-4bc3-4df7-8a09-765794883524
The number of the Prp lists and the number of the entries in last Prp list may be calculated wrongly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Baban Devkate <baban.devkate@seagate.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17208 6f19259b-4bc3-4df7-8a09-765794883524
Media->IoAlign field of BlockIo protocol instance installed by this driver should be set to the value of ScsiIo->IoAlign.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17195 6f19259b-4bc3-4df7-8a09-765794883524
The restriction of UsbHc2.SyncInterruptTransfer() on interrupt transfer direction is removed. This interface could support Interrupt IN/OUT now.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17041 6f19259b-4bc3-4df7-8a09-765794883524
Setting a bit in the PxSACT register for a command in the command list indicates
to the controller that the command list slot contains a native queued command (NCQ).
This can cause problems with some controllers (one such controller is the Marvell 9128).
Since NCQ commands are not used, don't set the PxACT register for commands issued.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chris Ruffin <chris.ruffin@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16536 6f19259b-4bc3-4df7-8a09-765794883524
- Fix EFI_IPv4_ADDRESS usages to use a macro to copy the structure
instead of direct assignment, to avoid runtime alignment errors.
- Fix a EFI_INPUT_KEY usage in TerminalDxe to use CopyMem() to copy the
structure instead of direct assignment, to avoid runtime alignment error.
- Delete excess local variables that are initialized but otherwise unused.
- CompilerIntrinsicsLib library now imported for AARCH64, as well as ARM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Randy Pawell <randy_pawell@hp.com>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16471 6f19259b-4bc3-4df7-8a09-765794883524
Per AHCI 1.1 spec, AE bit of GHC register is read-only if CAP.SAM is 1
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16321 6f19259b-4bc3-4df7-8a09-765794883524
DiskIoDxe: Fix ReadDiskEx and WriteDiskEx to not modify the user’s buffer when the BufferSize is 0.
DiskIoDxe: Fix ReadDiskEx and WriteDiskEx hang issue when the submitted blockio2 task is completed before submitting another blockio2 task.
DiskIoDxe: Fix FlushEx to free the flush task item in callback (memory leak issue).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16215 6f19259b-4bc3-4df7-8a09-765794883524
1. Add delay after set device address and get configuration descriptor.
2. Sync the change at R15876 in XhciDxe to do not access transfer ring when endpoint is isochronous type or control type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16105 6f19259b-4bc3-4df7-8a09-765794883524
1. Module UNI and Package UNI files are not DOS format. Convert them to DOS format.
2. Remove unused SectionExtractionDxeModStrs.uni and SectionExtractionPeiModStrs.uni
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16044 6f19259b-4bc3-4df7-8a09-765794883524
2. Add MODULE_UNI_FILE file that contains the localized Abstract and Description of a module.
a. Addresses an information gap between INF files and the UEFI Distribution Packaging Specification XML schema
b. There will be an associated update to UPT in BaseTools to consume MODULE_UNI_FILE and associated UNI file during UDP creation that performs the INF -> XML conversion.
c. There will be an associated update to UPT in BaseTools to produce MODULE_UNI_FILE and associated UNI file during UDP installation that performs the XML -> INF conversion.
3. Add Module Extra UNI file that provides the localized Name of a module.
a. [UserExtensions.TianoCore."ExtraFiles"] provides an easy method for a module to specify extra files not listed in [Sources] or [Binaries] sections to be added to a UDP without having to list the files in the UPT package information data file.
b. There will be an associated update to UPT in BaseTools to package up files listed in [UserExtensions.TianoCore."ExtraFiles"] during UDP creation.
c. UNI file contains localized name of a module to go along with the localized Abstract and Description from the MODULE_UNI_FILE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15963 6f19259b-4bc3-4df7-8a09-765794883524
1. Usage information in INF file comment blocks are either incomplete or incorrect.
This includes usage information for Protocols/PPIs/GUIDs/PCDs/HOBs/Events/BootModes.
The syntax for usage information in comment blocks is defined in the EDK II Module Information (INF) Specification
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15962 6f19259b-4bc3-4df7-8a09-765794883524
creation) of PciIoDevice->DevicePath. The bug can be triggered when
PciBusDxe is built into OVMF, with qemu/KVM device assignment of
a PCI-express device on the default 440FX machine type. OVMF
correctly discovers that the device is PCIe and begins probing
extended configuration space for the device. The root bridge
has no way to access extended config space and correctly errors,
sending us into the error reporting chain seen below. It's
possible that this error path could also be reproduced on physical
hardware when a PCI-to-PCIe bridge is present.
GatherDeviceInfo() | GatherPpbInfo() | GatherP2CInfo() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
CreatePciIoDevice() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
AllocateZeroPool()
LocateCapabilityRegBlock() [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoDevice->IsPciExp = TRUE
LocatePciExpressCapabilityRegBlock() [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoConfigRead() via funcptr [MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c]
RootBridgeIoPciRead() via funcptr [PcAtChipsetPkg/PciHostBridgeDxe/PciRootBridgeIo.c]
FAILS
REPORT_STATUS_CODE_WITH_DEVICE_PATH() [MdePkg/Include/Library/ReportStatusCodeLib.h]
ReportStatusCodeWithDevicePath() [MdeModulePkg/Library/DxeReportStatusCodeLib/ReportStatusCodeLib.c]
ASSERT (DevicePath != NULL) <--+
CreatePciDevicePath() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
sets PciIoDevice->DevicePath ----------+
In English:
- CreatePciIoDevice() allocates a zeroed out PCI_IO_DEVICE structure.
- PciIoConfigRead() tries to access the (extended) config space, and
fails.
- PciIoConfigRead() wants to report a status code (read error) for the
device path.
- Unfortuantely, PciIoDevice->DevicePath is still NULL at that point.
- The ASSERT() in ReportStatusCodeWithDevicePath() fires.
Fix it by moving CreatePciDevicePath() into CreatePciIoDevice(),
allowing PciIoDevice->DevicePath to be initialized before we
begin probing the device capabilities:
GatherDeviceInfo() | GatherPpbInfo() | GatherP2CInfo() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
CreatePciIoDevice() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
AllocateZeroPool()
CreatePciDevicePath() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
sets PciIoDevice->DevicePath -----------+
LocateCapabilityRegBlock() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoDevice->IsPciExp = TRUE |
LocatePciExpressCapabilityRegBlock() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoConfigRead() via funcptr | [MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c]
RootBridgeIoPciRead() via funcptr | [PcAtChipsetPkg/PciHostBridgeDxe/PciRootBridgeIo.c]
FAILS |
REPORT_STATUS_CODE_WITH_DEVICE_PATH() | [MdePkg/Include/Library/ReportStatusCodeLib.h]
ReportStatusCodeWithDevicePath() | [MdeModulePkg/Library/DxeReportStatusCodeLib/ReportStatusCodeLib.c]
ASSERT (DevicePath != NULL) <-----+
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15567 6f19259b-4bc3-4df7-8a09-765794883524
Besides this, the patch also fixed:
1) Wrong return value in SenseDataLength field of packet field of EFI_EXT_SCSI_PASS_THRU protocol, it should reflect real sense data length we got.
2) Wrong logic in ScsiDiskRequestSenseKeys that the logic makes SenseData pointer unaligned compared with BlockIo.Media.IoAlign field.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian, Feng <feng.tian@intel.com>
Reviewed-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Fu, Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15491 6f19259b-4bc3-4df7-8a09-765794883524
If the structure layout in UsbBusPei is changed, then the UsbBotPei will not work.
1. As the maximum number of endpoints is 16, use UINT16 type rather than UINT8 for DataToggle.
2. DataToggle needs to be reset to 0 when endpoint stall is cleared, do it in PeiUsbControlTransfer().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15185 6f19259b-4bc3-4df7-8a09-765794883524
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Leahy Leroy P <leroy.p.leahy@intel.com>
Reviewed-by: Lin Jie <jie.lin@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14952 6f19259b-4bc3-4df7-8a09-765794883524
Platforms such as Xen already enumerates PCI bridges and devices. Use
this PCD to control EDK2 behavior.
PcdPciDisableBusEnumeration is placed under [PcdsFixedAtBuild,
PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx], so that it is
possible to alter it during runtime.
The default setting of this PCD is false (allow full PCI enumeration) to
preserve the same behavior before this change.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14940 6f19259b-4bc3-4df7-8a09-765794883524
1.Port reset process may not be proper for some vendor's SS hubs. If the corresponding port shows the reset has been done by C_RESET bit we have to skip the whole reset process for attached devices.
2.Clean C_BH_RESET bit immediately to avoid usb timer entering too many times when 5 tiers hubs are connected.
3.Stop checking URB if there is an error happened.
4.Better error handling for fast hot-plug.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14889 6f19259b-4bc3-4df7-8a09-765794883524
1) The Queue size field in create I/O submission/completion queue cmds is 0-based. the current code is 1-based.
2) a typo on allocated memory page size. it's inconsistent that some places is using 4 pages, but a place is using 6 pages.
3) a typo on PRP/SGL mechanism judgment. should directly use Psdt field rather than Opc field.
4) some platforms may not support UINT64 width access on MMIO register. Fix it to use two 32-bit width access.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Kinney Michael <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14657 6f19259b-4bc3-4df7-8a09-765794883524
the PCI Bus driver through the function call NotifyPhase().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14483 6f19259b-4bc3-4df7-8a09-765794883524
The r14226 check-in indeed has memory leak in allocated "Child" pointer. UsbBusDriverBindingStop() may dereference this pointer and may bring exception on invalid memory access
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14251 6f19259b-4bc3-4df7-8a09-765794883524
1.enlarge the recovery time from 10ms to 20ms after port reset to make set address request success for better device compatibility.
2.another enhancement is to use RESET_C bit rather than RESET bit to judge if hub reset port operation is done.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14227 6f19259b-4bc3-4df7-8a09-765794883524
1.Fix the bug in interface parser logic for usb camera device. Reserve device address if the device doesn’t get disconnected.
2.Some usb 1.1 devices require the context evaluation immediately with actual max packet size after detecting the device max packet size.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14226 6f19259b-4bc3-4df7-8a09-765794883524
This way is used to avoid that the subsequent operations are treated as failure if the last operation is wrong.
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Sun Rui <rui.sun@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13663 6f19259b-4bc3-4df7-8a09-765794883524
Clean up the code to remove unnecessary NotifyHandle in the private data structure.
Signed-off-by: Ruiyu Ni<ruiyu.ni@intel.com>
Reviewed-by: Elvin Li<elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13565 6f19259b-4bc3-4df7-8a09-765794883524
Enhance ConSplitter to register hot keys for new connected consoles.
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hot Tian <hot.tian@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13358 6f19259b-4bc3-4df7-8a09-765794883524
Signed-off-by: Sun Rui <rui.sun@intel.com>
Reviewed-by: Fan Jeff <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13189 6f19259b-4bc3-4df7-8a09-765794883524
1) Fix a bug on missing hub context evaluation operation.
2) If the usb keyboard device configuration has been set successfully, then don’t set configuration again.
Signed-off-by: erictian
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13087 6f19259b-4bc3-4df7-8a09-765794883524
1) XHCI host controller hw always provides more than 5 interrupters.
Now using interrupter 0 to accommodate all received events.
2) XHCI host controller hw always provides 32bytes context size.
Now it dynamically detect context size and construct it.
also solved several issues:
1) Divides 64byte width register access to two 32bit registers access because some XHCI chipsets cannot support a single 64bit access.
2) Remove halt host controller statement in UsbBusDriverBindingStop(). It has been done by host controller’s DriverBindingStop(). And XhciDriverBindingStop() need XHCI host controller is in running state because it need execute DISABLE_SLOT cmd to release h/w resource.
signed-off-by: erictian
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12785 6f19259b-4bc3-4df7-8a09-765794883524
1. move the non-blocking task related setting ahead to store the MapTable and PageCount in case there is a IO operation error happened then the error handler code could use those information to release the resource.
2. Enlarge the TPL protective area to make sure the simulative delay time is accurate when there is mixing usage of Non blocking and blocking I/O.
Signed-off-by: qianouyang
Reviewed-by: erictian
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12712 6f19259b-4bc3-4df7-8a09-765794883524
1. Boost IDE mode boot when slave device is absent.
2. Use D2H FIS to check if the PIO OUT/DMA IN/DMA OUT transfer is finished or error happened. ATA PIO IN has special check as it may just receive PIO SETUP FIS for success case.
3. Add command status register check for IDE DMA transfer.
4. ScsiDiskReadCapacity() in ScsiDisk should return EFI_SUCCESS if SENSE Data request is success.
Signed-off-by: erictian
Reviewed-by: rsun3
Reviewed-by: xdu2
Reviewed-by: mdkinney
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12658 6f19259b-4bc3-4df7-8a09-765794883524
GCC 4.6 generates a warning when a variable is set,
but never used.
Signed-off-by: jljusten
Reviewed-by: lgao4
Reviewed-by: erictian
Reviewed-by: rsun3
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12617 6f19259b-4bc3-4df7-8a09-765794883524
* Check if the machine type of the image is supported by the current UEFI system.
* Ignore the image if it is an EFI application as required by the UEFI spec.
Signed-off-by: rsun3
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12465 6f19259b-4bc3-4df7-8a09-765794883524
0. Remove the unused private GUID from module source files.
1. Use gEfiCallerIdGuid replace of the private module GUID.
2. Add the public header files to define HII FormSet and PackageList GUID used in every HII driver.
3. Move two EBC protocols for debug purpose from EBC driver to MdeModulePkg Include directory.
Signed-off-by: lgao4
Reviewed-by: ydong10 gdong1 tye jfan12 wli12 rsun3 jyao1
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12373 6f19259b-4bc3-4df7-8a09-765794883524
1. Fix the incorrect definition of EFI_PCI_IO_ATTRIBUTE_VGA_IO_16 (does not conform to the UEFI spec) in PciIo.h.
2. Add missing definitions of ISA and VGA IO attributes in PCI Root Bridge IO protocol.
3. Improve the algorithm in the PCI bus driver to get PCI platform policy from PCI Platform Protocol and PCI Override Protocol.
4. Update the PCI bus driver to use the PCI platform policy to determine the supported attributes that are returned by the EFI_PCI_IO_PROTOCOL.Attributes() function. This is required by the PI spec.
5. Add a backward compatibility workaround for PCI VGA drivers in Option ROM, which typically sets VGA_IO without checking supported attributes.
6. Update the PCI host bridge driver in PcAtChipsetPkg to report VGA_IO_16 and ISA_IO_16 instead of VGA_IO/ISA_IO attributes. Modern chipsets don’t have hardware capability to control 10-bit or 16-bit decoding for ISA/VGA aliases.
7. Update LPC/VGA device drivers to check supported attributes of VGA_IO/VGA_IO_16 or ISA_IO/ISA_IO_16.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11204 6f19259b-4bc3-4df7-8a09-765794883524
2. update SerialNumber comparing logic to handle possible NULL-terminator in WWID device path
3. fix bug in UsbIo->UsbIoGetSupportedLanguages(): TableSize is size in bytes of LangIDTable instead of number of LangID.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11197 6f19259b-4bc3-4df7-8a09-765794883524
This check-in fix the issue by adding a flag to indicate if a HPC is found during PCI enumeration or not. This check-in also adds a debug message if any found HPC failed with initialization.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11081 6f19259b-4bc3-4df7-8a09-765794883524
This solution defines a PCD Feature Flag to enabled support for unaligned requests through the PCI I/O Protocol. This flag is disabled by default. Platforms that do want to support such EFI/UEFI drivers that make unaligned PCI I/O requests should enable this feature.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11016 6f19259b-4bc3-4df7-8a09-765794883524
But current PCI bus driver has a bug that if a P2P bridge has no child devices detected during enumeration, the bits won’t be set. This may impact PCI hot plug capable bridges because the OS may re-assign resources for them causing the reserved resource by the firmware will be overwritten.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11013 6f19259b-4bc3-4df7-8a09-765794883524
Feng Tian
Ruiyu Ni
Michael D Kinney
Qiu Shumin
Olivier Martin
Laszlo Ersek
Chris Ruffin
Randy Pawell
Samer El-Haj-Mahmoud
jaben carsey
Reza Jelveh
Star Zeng
Nikolai Saoukh
Gao, Liming
Elvin Li
Chen Fan
Eric Dong
Alex Williamson
Tian, Hot
Wei Liu
Sergey Isakov
erictian
niruiyu
ydong10
li-elvin
lzeng14
qianouyang
rsun3
lgao4
jljusten
vanjeff
oliviermartin
andrewfish
hhuan13
mdkinney
xdu2