The patch separates the common logic in XhcControlTransfer,
XhcBulkTransfer and XhcSyncIntTransfer to a sub-routine
XhcTransfer. It doesn't have functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Current implementation of IsTransferRingTrb only checks whether
the TRB is in the RING of the URB.
The patch enhanced the logic to check that whether the TRB belongs
to the transaction of URB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
The SATA spec mandates that link detection by the PHY completes within
10 ms after receiving a reset signal. However, there is no obligation
to uphold this requirement at the driver end as strictly as we do, and
as it turns out, some combinations of host and device (e.g., Samsung
850 EVO connected to a LeMaker Cello) are only borderline compliant,
which means the device is not detected reliably.
So let's allow for a bit of margin, and increase the PHY detect timeout
value to 15 ms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some USB devices don't report data periodically through Int
Transfer. They report data only when be asked. If the TRB
is not removed from the XHCI HW, when next time HOST asks
data again, the data is reported but consumed by the previous
TRB, which results the HOST thinks data never comes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When "reconnect -r" is typed in shell, UsbFreeInterface() is called
to uninstall the UsbIo and DevicePath. But When a UsbIo is opened
by a driver and that driver rejects to close the UsbIo in Stop(),
the uninstall doesn't succeed.
But UsbFreeInterface () frees the DevicePath memory without check
whether the uninstall succeeds.
It leads to the DXE core database contain a DevicePath instance but
that instance's memory is freed.
Assertion happens when someone calls InstallProtocol(DevicePath)
because the InstallProtocol() checks all DevicePath instance to
find whether the same one exits in database.
We haven't seen any USB device driver which rejects to close UsbIo
in Stop(), but it's very likely.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=510
The commit fills the 'Interval' field of the Endpoint Context data for
isochronous endpoints. It will resolve the error when a Configure
Endpoint Command is sent to an isochronous endpoint.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
If IOMMU protocol is installed, PciBus need call IOMMU
to set access attribute for the PCI device in Map/Ummap.
Only after the access attribute is set, the PCI device can
access the DMA memory.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Previous patch Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Previous patch Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
If IOMMU protocol is installed, PciHostBridge just calls
IOMMU AllocateBuffer/FreeBuffer/Map/Unmap.
PciHostBridge does not set IOMMU access attribute,
because it does not know which device request the DMA.
This work is done by PciBus driver.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Previous patch Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Previous patch Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
For function UfsPassThruGetTargetLun(), the length of the input device
node specified by 'DevicePath' should be compared with the size of
'UFS_DEVICE_PATH' rather than the size of 'SCSI_DEVICE_PATH'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In function UfsHcDriverBindingStart(), the return value 'Status' may be
overridden during the original PCI attributes restore process.
This commit refines the logic to avoid such override.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit removes the unused field 'EFI_HANDLE Handle' in Ufs host
controller private data structure 'UFS_HOST_CONTROLLER_PRIVATE_DATA'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In case of an async command if updating the submission queue tail
doorbell fails then the command will not be picked up by device and
no completion response will be created. This scenario has to be handled.
Also if we create an AsyncRequest element and insert in the async queue,
it will never receive a completion so in the timer routine this element
won't be freed, resulting in memory leak. Also in case of blocking calls
we should capture the status of updating completion queue head doorbell
register and return it to caller of PassThru.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Suman Prakash <suman.p@samsung.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
In the origin codes, the host sets the fDeviceInit flag to initiate device
initialization, but does not check whether the device resets this flag
to indicate the device initialization is completed.
Details can be referred at UFS 2.0 Spec Section 14.2 - Flags.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function PeiUsbReadCapacity(), the following expression:
LastBlock = (Data.LastLba3 << 24) |
(Data.LastLba2 << 16) |
(Data.LastLba1 << 8) |
Data.LastLba0;
(There is also a similar case in function PeiUsbReadFormattedCapacity().)
will involve undefined behavior in signed left shift operations.
Since Data.LastLbaX is of type UINT8, they will be promoted to int (32
bits, signed) first, and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Data.LastLba3 is 1, (Data.LastLba3 << 24) will be out of
the range within int type. The undefined behavior of the signed left shift
might incur potential issues.
This commit will add an explicit UINT32 type cast for Data.LastLba3 to
refine the codes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function UfsBlockIoPeimGetMediaInfo(), the following expression:
Private->Media[DeviceIndex].LastBlock = (Capacity16.LastLba3 << 24) |
(Capacity16.LastLba2 << 16) |
(Capacity16.LastLba1 << 8) |
Capacity16.LastLba0;
(There is also a similar case in this function.)
will involve undefined behavior in signed left shift operations.
Since Capacity16.LastLbaX is of type UINT8, and
Private->Media[DeviceIndex].LastBlock is of type UINT64. Therefore,
Capacity16.LastLbaX will be promoted to int (32 bits, signed) first, and
then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Capacity16.LastLba3 is 1, (Capacity16.LastLba3 << 24) will
be out of the range within int type. The undefined behavior of the signed
left shift will lead to a potential of setting the high 32 bits of
Private->Media[DeviceIndex].LastBlock to 1 during the cast from type int
to type UINT64.
This commit will add an explicit UINT32 type cast for Capacity16.LastLba3
to resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function ReadCapacity(), the following expression:
MediaInfo->LastBlock = (Data.LastLba3 << 24) |
(Data.LastLba2 << 16) |
(Data.LastLba1 << 8) |
Data.LastLba0;
(There is also a similar case in this function.)
will involve undefined behavior in signed left shift operations.
Since Data.LastLbaX is of type UINT8, and MediaInfo->LastBlock is of type
UINTN. Therefore, Data.LastLbaX will be promoted to int (32 bits, signed)
first, and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Data.LastLba3 is 1, (Data.LastLba3 << 24) will be out of
the range within int type. The undefined behavior of the signed left shift
will lead to a potential of setting the high 32 bits of
MediaInfo->LastBlock to 1 during the cast from type int to type UINT64
for X64 builds.
This commit will add an explicit UINT32 type cast for Data.LastLba3 to
resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function GetMediaInfo(), the following expression:
ScsiDiskDevice->BlkIo.Media->LastBlock = (Capacity10->LastLba3 << 24) |
(Capacity10->LastLba2 << 16) |
(Capacity10->LastLba1 << 8) |
Capacity10->LastLba0;
will involve undefined behavior in signed left shift operations.
Since Capacity10->LastLbaX is of type UINT8, and
ScsiDiskDevice->BlkIo.Media->LastBlock is of type UINT64. Therefore,
Capacity10->LastLbaX will be promoted to int (32 bits, signed) first,
and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Capacity10->LastLba3 is 1, (Capacity10->LastLba3 << 24)
will be out of the range within int type. The undefined behavior of the
signed left shift will lead to a potential of setting the high 32 bits
of ScsiDiskDevice->BlkIo.Media->LastBlock to 1 during the cast from type
int to type UINT64.
This commit will add an explicit UINT32 type cast for
Capacity10->LastLba3 to resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
For async commands, the buffer allocated for Prp list is
not getting freed, which will cause memory leak for async
read write command. For example testing async command flow
with custom application to send multiple read write commands
were resulting in decrease of available memory page in memmap,
which eventually resulted in system hang. Hence freeing
AsyncRequest->MapData, AsyncRequest->MapMeta, AsyncRequest->MapPrpList and
AsyncRequest->PrpListHost when async command is completed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Suman Prakash <suman.p@samsung.com.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
At worst case, OCR register may always not set BIT31. It will cause
original code enter to dead loop. Adding a break for such case.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
There are cases that the operands of an expression are all with rank less
than UINT64/INT64 and the result of the expression is explicitly cast to
UINT64/INT64 to fit the target size.
An example will be:
UINT32 a,b;
// a and b can be any unsigned int type with rank less than UINT64, like
// UINT8, UINT16, etc.
UINT64 c;
c = (UINT64) (a + b);
Some static code checkers may warn that the expression result might
overflow within the rank of "int" (integer promotions) and the result is
then cast to a bigger size.
The commit refines codes by the following rules:
1). When the expression is possible to overflow the range of unsigned int/
int:
c = (UINT64)a + b;
2). When the expression will not overflow within the rank of "int", remove
the explicit type casts:
c = a + b;
3). When the expression will be cast to pointer of possible greater size:
UINT32 a,b;
VOID *c;
c = (VOID *)(UINTN)(a + b); --> c = (VOID *)((UINTN)a + b);
4). When one side of a comparison expression contains only operands with
rank less than UINT32:
UINT8 a;
UINT16 b;
UINTN c;
if ((UINTN)(a + b) > c) {...} --> if (((UINT32)a + b) > c) {...}
For rule 4), if we remove the 'UINTN' type cast like:
if (a + b > c) {...}
The VS compiler will complain with warning C4018 (signed/unsigned
mismatch, level 3 warning) due to promoting 'a + b' to type 'int'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
For pointer subtraction, the result is of type "ptrdiff_t". According to
the C11 standard (Committee Draft - April 12, 2011):
"When two pointers are subtracted, both shall point to elements of the
same array object, or one past the last element of the array object; the
result is the difference of the subscripts of the two array elements. The
size of the result is implementation-defined, and its type (a signed
integer type) is ptrdiff_t defined in the <stddef.h> header. If the result
is not representable in an object of that type, the behavior is
undefined."
In our codes, there are cases that the pointer subtraction is not
performed by pointers to elements of the same array object. This might
lead to potential issues, since the behavior is undefined according to C11
standard.
Also, since the size of type "ptrdiff_t" is implementation-defined. Some
static code checkers may warn that the pointer subtraction might underflow
first and then being cast to a bigger size. For example:
UINT8 *Ptr1, *Ptr2;
UINTN PtrDiff;
...
PtrDiff = (UINTN) (Ptr1 - Ptr2);
The commit will refine the pointer subtraction expressions by casting each
pointer to UINTN first and then perform the subtraction:
PtrDiff = (UINTN) Ptr1 - (UINTN) Ptr2;
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Compiler calculates the PciBar[BarIndex] using
sizeof (PciBar[0]) * BarIndex, when BarIndex is type of UINT64,
the above calculation generates assembly code using _allmul.
Change BarIndex to UINTN to avoid the build failure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
When the VendorId/DeviceId/RevisionId/SubsystemVendorId
/SubsystemDeviceId is MAX_UINTN, IncompatiblePciDeviceSupport
driver doesn't use it to match any IDs.
The patch fixes this bug.
Since PciBus driver always calls IncompatiblePciDeviceSupport
using IDs read from HW, MAX_UINTN is never passed to this
driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The patch replaces the following macros:
DEVICE_ID_NOCARE (0xFF) --> MAX_UINT64
PCI_ACPI_UNUSED (0) --> 0
PCI_BAR_ALL (0xFF) --> MAX_UINT64
PCI_BAR_NOCHANGE (0) --> 0
PCI_BAR_EVEN_ALIGN --> EVEN_ALIGN (local definition)
Since the PciBus driver was updated to accept Spec defined values
in previous commit, the above replacements don't impact
functionality.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
PI spec IncompatiblePciSupport part defines (UINT64)-1 as all BARs
and 0 to use existing alignment. PciBus driver didn't accept these
values. It treated 0xFF as all BARs and 0xFFFFFFFFFFFFFFFFULL to use
existing alignment.
The patch changes the code to still accept old values while also
accept values defined in PI spec. So that the driver can provide
backward compatibility and follow spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When BarIndex equals to 0xFF, default value 0 is used as the BAR
index. Though PCI_BAR_ALL and MAX_UINT8 shares the same value,
using PCI_BAR_ALL is like to match any BAR not BAR 0, it's more
proper to use MAX_UINT8 here.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If the code eventually returns "Status" anyway, it does not make
sense to explicitly return "Status" in case of an error, too.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UPIU packet is sent, (BIT0 << Slot) should be set according
to context. But BIT0 is used without Slot when UfsWaitMemSet ()
is invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UPIU packet is sent, (BIT0 << Slot) should be set according
to context. But BIT0 is used without Slot when UfsWaitMemSet ()
is invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UFS_HC_CAP_64ADDR bit is set, it means 64-bit address,
not 32-bit address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Refine the codes to compare the definition 'SIZE_4GB' with type
EFI_PHYSICAL_ADDRESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Add support for non-coherent DMA, either by performing explicit cache
maintenance when DMA mappings are aligned to the CPU's DMA buffer alignment,
or by bounce buffering via uncached mappings otherwise.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Fix switch/case statement type mismatch in functions PciIoMemRead &
PciIoMemWrite.
Parameter 'Width' is of enum type EFI_PCI_IO_PROTOCOL_WIDTH, but the enum
type provided in 'switch (Width)' block is of type
EFI_PCI_ROOT_BRIDGE_IO_PROTOCOL_WIDTH.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Add missing EFIAPI modifiers to the functions that are exposed via the
PCI I/O protocol.
At the same time, add a missing UINT8 cast which breaks the build on
Visual Studio.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
This implements support for non-discoverable PCI compatible devices, i.e,
devices that are not on a PCI bus but that can be controlled by generic PCI
drivers in EDK2.
This is implemented as a UEFI driver, which means we take full advantage
of the UEFI driver model, and only instantiate those devices that are
necessary for booting.
Care is taken to deal with DMA addressing limitations: DMA mappings and
allocations are moved below 4 GB if the PCI driver has not informed us
that the device being driven is 64-bit DMA capable. DMA is implemented as
coherent, support for non-coherent DMA is implemented by a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Port status bits are clear in original code, so no enumeration
takes place.
Changing this to prevent the status bits from being cleared
allows enumeration to proceed normally.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Mike Turner <Michael.Turner@microsoft.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mike Turner <Michael.Turner@microsoft.com>
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit e27cca has a typo on DEBUG level macro. And this debug
message should be DEBUG_INFO rather than DEBUG_ERROR.
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
reviewed-by: Marcin Wojtas <mw@semihalf.com>
EFI_D_INFO, EFI_D_VERBOSE, EFI_D_WARN and EFI_D_ERROR are replaced
with currently recommended values.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to AHCI Spec 1.3 GHC.AE bit description:
"The implementation of this bit is dependent upon the value of the
CAP.SAM bit. If CAP.SAM is '0', then GHC.AE shall be read-write and shall
have a reset value of '0'. If CAP.SAM is '1', then AE shall be read-only
and shall have a reset value of '1'."
Being in AhciMode, for proper operation it is required, that GHC.AE bit
is always set, before any other AHCI registers are written to. Current
AhciMode implementation, both in AhciReset() and AhciModeInitialization()
functions, set GHC.AE bit only depending on 'CAP.SAM == 0' condition,
assuming (according to the AHCI spec), that otherwise it has to be set
anyway. It may however happen, that even if 'CAP.SAM == 1', GHC.AE
requires updating by software.
This patch enables in AhciMode setting GHC.AE in case its initial value
is '0'. It fixes AHCI support for Marvell Armada 70x0 and 80x0 SoC
families. The change is transparent to all other platforms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
We send ADDRESS DEVICE CMD in XhcInitializeDeviceSlot(), which will
cause XHC issue a USB SET_ADDRESS request to the USB Device.
According to USB spec, there should have a 10ms delay before this
operation after resetting a given port.
But in original code, there is a possible path which may have no such
10ms delay:
UsbHubResetPort()->UsbHubSetPortFeature()->Stall(20)->UsbHubGetPortSt
atus()->XhcPollPortStatusChange()->(if RESET_C bit is set)->
XhcInitializeDeviceSlot()->(if RESET_C bit is set)->Stall(10)
So this patch is used to fix above issue.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Tested-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch is used to revert changes done in commit 17f3e942
bc527fbd75068d2d5752b6af54917487 - "MdeModulePkg/UsbMass: Not
retry if usb bot transfer execution fail"
It's because Usb Floppy will report DEVICE_ERROR for the first
several cmds when it need spin up. so retry logic makes sense.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When PciSioSerial is firstly started with a non-NULL remaining
device path, the UART instance is created using the parameters
specified in the remaining device path. Later when the driver
is started again on the same UART controller with NULL remaining
device path, the correct logic is to directly return SUCCESS
instead of current buggy implementation which wrongly produces
another UART using the default parameters.
The bug causes two UARTs are created when the UART is configured
in 57600 baud rate.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
According to UFS Host Controller Spec(JESD223), the bits 1:0 of this
DataByteCount field shall be 11b to indicate Dword granularity.
But the size of UFS Request Sense Data Response defined in UFS Spec
(JESD220C) is 18 which is not Dword aligned, we would have to round
down to the multiple of 4 to fill the DBC field to avoid bring issue
on some UFS HCs.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Short Packet case is a normal case, we shouldn't print it as an error
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
AhciDumpPortStatus doesn't fully populate all the fields of
AtaStatusBlock after completing command execution, which may bring
issue if someone depends on the return status.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The 'universal' PCI bus driver in MdeModulePkg contains a quirk to
degrade 64-bit PCI MMIO BARs to 32-bit in the presence of an option
ROM on the same PCI controller.
This quirk is highly specific to not just the X64 architecture in general,
but to the PC platform in particular, given that only X64 platforms that
require legacy PC BIOS compatibility require it. However, making the
quirk dependent on the presence of the legacy BIOS protocol met with
resistance, due to the fact that it introduces a dependency on the
IntelFrameworkModulePkg package.
So instead, make the quirk configurable, by introducing a feature flag PCD
'PcdPciDegradeResourceForOptionRom' which defaults to TRUE only for X64.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Currently, the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute is completely
ignored by the PCI host bridge driver, which means that, on an implementation
that supports DMA above 4 GB, allocations above 4 GB may be provided to
devices that have not expressed support for it.
So in addition to checking 'RootBridge->DmaAbove4G' to establish whether the
root bridge itself supports DMA above 4 GB, we must also take into account
the operation type (EfiPciOperationBusMaster{Read|Write|CommonBuffer}64),
and the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute, when mapping and
allocating DMA memory, respectively.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Since current codes in NvmExpressDxe already support the non-blocking I/O
feature for EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL interface, the relative bit
in the 'Attributes' field of EFI_NVM_EXPRESS_PASS_THRU_MODE should be set
to reflect this.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit fixes the issue that the caller event passed to
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() will not be signaled for
NVME Admin commands.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru()
should return EFI_INVALID_PARAMETER if the input 'NamespaceId' is invalid
for the NVM Express controller. This commit adds check in PassThru() to
follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit adds serveral checks for the 'Packet' parameter passed to the
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() API:
The check for the 'TransferLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value will not
exceed the maximum data transfer size allowed by a controller.
The check for the 'TransferBuffer' and 'TransferLength' fields in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET when the Opcode of an NVME
command indicates a data transfer between controller and host.
The check for the 'MetadataLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value is not 0
when the corresponding 'MetadataBuffer' field has a non-NULL value.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to UEFI spec, an EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL with neither
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_LOGICAL nor
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_PHYSICAL set in the Attributes field
is an illegal configuration.
This commit adds this check in the PassThru API to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, the 'TransferBuffer' and 'MetadataBuffer' used
in a data transfer should be aligned on the boundary specified by the
IoAlign field in the EFI_NVM_EXPRESS_PASS_THRU_MODE structure.
This commit adds this check to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNextNamespace() should return
EFI_NOT_FOUND when the value pointed to by NamespaceId is the namespace ID
of the last namespace on the NVM Express controller. This commit modifies
the check for NamespaceId to follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNamespace() should return
EFI_NOT_FOUND when the input DevicePath is a device path node type that
the NVM Express Pass Thru driver supports, but there is not a valid
translation from DevicePath to a namespace ID. Current code will return
EFI_SUCCESS. This commit adds additional check in the GetNameSpace API to
make sure correct status is returned.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.BuildDevicePath() should return
EFI_NOT_FOUND when the input NamespaceId is not valid. However, current
code returns EFI_DEVICE_ERROR instead. This commit modifies the check for
input NamespaceId to return the correct status.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The gBS->OpenProtocol() calls to open EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL
in NvmExpress.c will crash the data in 'Mode' field of
'Private->Passthru'.
The third parameter of gBS->OpenProtocol() is an output parameter that
stores the address where a pointer to the corresponding Protocol
Interface. The current code mistakenly pass '&Private->Passthru' (a
pointer of the EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL) as the third
parameter. This will crash the data in 'Mode' filed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The retry mechanism will bring issue if the usb device is unplugged
from XHCI HC but s/w is trying to access it through BlockIo. The
current cmd will get device error return status, but the sequential
cmds will be timeout. This behavior will cause system unresponsive
for a long while and bring bad user experience.
So we break the retry loop if found device error.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The last TRB in transfer ring is a LINK type TRB, which shouldn't
be accounted as a valid item in IsAsyncIntTrb().
Without this fix, the original algo will bring issue on those URBs
whose TRBs crosses the transfer ring.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This change is used to remove the port status polling in port reset
functions.
Why it's needed is because:
1) The same polling on same port has taken place prior to this removed
one. See UsbEnumeratePort()->GetPortStatus(). So this polling in
UsbEnumerateNewDev()->ResetPort() is redundant.
2) EDKII Xhci driver hooks all GetPortStatus() operations. If we don't
remove this one, XHCI driver's XhcPollPortStatusChange() may enter twice
in reset process and wrongly think the device is unplugged.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The Host Controller reset has been done at EDKII UHCI/EHCI/XHCI, The
original code will do twice host controller initialization which is
unnecessary. It also bring issues on some USB HCs.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
> cc1: warnings being treated as errors
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:
> In function 'GetProposedResources':
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:1388:
> error: integer constant is too large for 'long' type
Append a ULL suffix to the replacement text of PCI_RESOURCE_LESS that is
aligned with the style of the EFI_RESOURCE_SATISFIED and
EFI_RESOURCE_NOT_SATISFIED macros.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Section 7.8.2 of the PCI Express specification (r4.0 v0.3), entitled "PCI
Express Capabilities Register (Offset 02h)", and section 7.8.9 "Slot
Capabilities Register (Offset 14h)" of the same, describe the conditions
when a PCIe port should be considered "supporting hotplug":
- it should be a root complex port or a switch downstream port, and
- it should have the "Slot Implemented" bit set in the Express
Capabilities Register, and
- it should have the "Hot-Plug Capable" bit set in the Slot Capabilities
Register.
The first two sub-conditions are already implemented in at least two open
source projects I could find:
- in SeaBIOS by Marcel Apfelbaum: "hw/pci: reserve IO and mem for pci
express downstream ports with no devices attached"
<https://code.coreboot.org/p/seabios/source/commit/3aa31d7d6375>,
- in edk2 itself, in the implementation of the "PCI" UEFI Shell command:
see the "PcieExplainTypeSlot" case label in function
PciExplainPciExpress(), file
"ShellPkg/Library/UefiShellDebug1CommandsLib/Pci.c".
PciBusDxe recognizes such PCIe ports as bridges, but it doesn't realize
they support hotplug. In turn PciBusDxe omits getting any resource padding
information from the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL for these
bridges:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Implement a function called SupportsPcieHotplug() for identifying such
ports, and call it from IsPciHotPlugBus() (after the call to IsSHPC()).
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
The PCI Hot Plug capability register block is marked with capability ID
0x0C (EFI_PCI_CAPABILITY_ID_SHPC), not 0x06
(EFI_PCI_CAPABILITY_ID_HOTPLUG).
This bug prevents PciBusDxe from recognizing whether a PCI-to-PCI bridge
supports hotplug. In turn the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL is
not consulted for resource padding information:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
IsSHPC() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Look for the correct capability ID.
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
If there is no port multiplier (PortMultiplierPort = 0xFFFF), current code
in functions TransferAtaDevice() and TrustTransferAtaDevice() will always
set the DEV bit of the ATA device register. It causes that ATA commands
cannot be sent to some ATA hard drives.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
- abstrated to abstracted
- accessibla to accessible
- addres to address
- apropriate to appropriate
- arry to array
- availabe to available
- avaliable to available
- becasue to because
- correponding to corresponding
- etablished to established
- exeuction to execution
- extensiable to extensible
- fileds to fields
- loadding to loading
- ptototypes to prototypes
- prococol protocol
- requried to required
- resoruce to resource
- runing to running
- uild to build
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Ruiyu Ni
Ard Biesheuvel
Dandan Bi
Hao Wu
Jiewen Yao
Suman Prakash
Feng Tian
Thomas Huth
Haojian Zhuang
Star Zeng
Marcin Wojtas
Laszlo Ersek
Gary Lin
Giri P Mudusuru