REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2329
XD (ExecutionDisable) feature, when turned on, allows page table
entry BIT63 set to 1 indicating the memory pointed by the page table
is disallowed to execute.
DxeIpl::CreateIdentityMappingPageTables() enables the XD when CPU
supports it.
Later DxeCore modifies the page table to set the BIT63 to protect
the stack/heap to disallow code execution in stack/heap.
UefiCpuPkg/CpuCommonFeaturesLib enables/disables the XD feature
according to PcdCpuFeaturesSetting.
When XD is disabled, GP fault is generated immediately because some
page entries have BIT63 set.
To fix this issue, this patch removes the XD feature logic from
UefiCpuPkg/CpuCommonFeaturesLib so the XD feature is only taken
care of by DxeIpl.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
MpInitLib sets X2ApicEnable in two places.
1. CollectProcessorCount()
This function is called when MpInitLibInitialize() hasn't been
called before.
It sets X2ApicEnable and later in the same function it configures
all CPUs to operate in X2 APIC mode.
2. MpInitLibInitialize()
The X2ApicEnable setting happens when this function is called in
second time. But after that setting, no code consumes that flag.
With the above analysis and with the purpose of simplifying the code,
the X2ApicEnable in #1 is changed to local variable and the #2 can be
changed to remove the setting of X2ApicEnable.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Today's logic sets X2ApicEnable flag in each AP's initialization
path when InitFlag == ApInitConfig.
Since all CPUs update the same global data, a spin-lock is used
to avoid modifications from multiple CPUs happen at the same time.
The spin-lock causes two problems:
1. Potential performance downgrade.
2. Undefined behavior when improper timer lib is used.
For example we saw certain platforms used AcpiTimerLib from
PcAtChipsetPkg and that library depends on retrieving PeiServices
from idtr. But in fact AP's (idtr - 4) doesn't point to
PeiServices.
The patch simplifies the code to let BSP set the X2ApicEnable flag so
the spin-lock acquisition from AP is not needed any more.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
- If a platform boots such that the boot CPU count is smaller than
PcdCpuMaxLogicalProcessorNumber, then the platform cannot use the "fast
AP detection" logic added in commit 6e1987f19a. (Which has been
documented as a subset of use case (2) in the previous patch.)
Said logic depends on the boot CPU count being equal to
PcdCpuMaxLogicalProcessorNumber. If the equality does not hold, the
platform either has to wait too long, or risk missing APs due to an
early timeout.
- The platform may not be able to use the variant added in commit
0594ec417c either. (Which has been documented as use case (1) in the
previous patch.)
See commit 861218740d. When OVMF runs on QEMU/KVM, APs may check in
with the BSP in arbitrary order, plus the individual AP may take
arbitrarily long to check-in. If "NumApsExecuting" falls to zero
mid-enumeration, APs will be missed.
Allow platforms to specify the exact boot CPU count, independently of
PcdCpuMaxLogicalProcessorNumber. In this mode, the BSP waits for all APs
to check-in regardless of timeout. If at least one AP fails to check-in,
then the AP enumeration hangs forever. That is the desired behavior when
the exact boot CPU count is known in advance. (A hung boot is better than
an AP checking-in after timeout, and executing code from released
storage.)
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Before adding another AP enumeration mode, clarify the documentation on
the current logic. No functional changes.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2150
v4:
The v3 posting didn't do what it promised to do, so do it now for real.
V3 changes:
change to mov instruction (non locking instuction) instead
of xchg to simplify design.
V2 changes:
Add xchg 16 bit instructions to handle sgdt and sidt base
63:48 bits and 47:32 bits.
Add comment to explain why xchg 64bit isnt being used
Split lock happens when a locking instruction is used on mis-aligned data
that crosses two cachelines. If close source platform enables Alignment
Check Exception(#AC), They can hit a double fault due to split lock being
in CpuExceptionHandlerLib.
sigt and sgdt saves 10 bytes to memory, 8 bytes is base and 2 bytes is limit.
The data is mis-aligned, can cross two cacheline, and a xchg
instruction(locking instuction) is being utilize.
Signed-off-by: John E Lofgren <john.e.lofgren@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1909
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Amy Chan <amy.chan@intel.com>
Cc: Rangasai V Chaganty <rangasai.v.chaganty@intel.com>
Signed-off-by: Donald Kuo <donald.kuo@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2040
Below code is current implementation:
if (MsrRegister[ProcessorNumber].Bits.Lock == 0) {
CPU_REGISTER_TABLE_WRITE_FIELD (
ProcessorNumber,
Msr,
MSR_IA32_FEATURE_CONTROL,
MSR_IA32_FEATURE_CONTROL_REGISTER,
Bits.Lock,
1
);
}
1. In first normal boot, the Bits.Lock is 0, 1 will be added
into the register table and then will set to the MSR.
2. Trig warm reboot, MSR value preserves. After normal boot phase,
the Bits.Lock is 1, so it will not be added into the register
table during the warm reboot phase.
3. Trig S3 then resume, the Bits.Lock change to 0 and Bits.Lock is
not added in register table, so it's still 0 after resume. This
is not an expect behavior. The expect value is the value should
always 1 after booting or resuming from S3.
The root cause for this issue is
1. driver bases on current value to insert the "set value action" to
the register table.
2. Some MSRs may reserve their value during warm reboot.
The solution for this issue is using new added macros for the MSRs which
preserve value during warm reboot.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2040
Supports new logic which test current value before write new value.
Only write new value when current value not same as new value.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2040
Add below new micros which test the current value before write the new
value. Only write new value when current value not same as new value.
CPU_REGISTER_TABLE_TEST_THEN_WRITE32
CPU_REGISTER_TABLE_TEST_THEN_WRITE64
CPU_REGISTER_TABLE_TEST_THEN_WRITE_FIELD
Also add below API:
CpuRegisterTableTestThenWrite
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2060
Remove the useless ConsoleLogLock spinlock.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2008
MpInitLib is the library that's responsible to wake up APs to provide
MP PPI and Protocol services.
The patch synchronizes BSP's CR4.LA57 to each AP's CR4.LA57.
Without this change, AP may enter to GP fault when BSP's 5-level page
table is set to AP during AP wakes up.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
This debug message may be called by BSP and APs. It may
caused ASSERT when APs call this debug code.
In order to avoid system boot assert, Remove this debug
message.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1982
MpInitLibInitialize in MpLib.c will be invoked on both PEI and DXE
CPU code, MicrocodeDetect would be performed twice and copy
Microcode from flash to memory twice as well, which consider as
duplicate work to lead longer boot time.
This patch just use microcode memory copied in PEI phase if exist.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1973
For semaphore type register, it required all processors to do the
task at the same time.
Current logic begins BSP's task after all APs have finished their tasks.
This will caused set semaphore task hang if semaphore has package
level type.
This patch use new EDKII_PEI_MP_SERVICES2_PPI to start all processors at
the same time to fix the potential hang issue.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1973
Add new MpInitLibStartupAllCPUs API uses to start all processors
at the same time.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1973
Add new MpInitLibStartupAllCPUs API uses to start all processors
at the same time.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1972
Function in this library may be used by APs. Assert will be trig if AP
uses dynamic pcd.
This patch enhance the current code, remove the unnecessary usage of
dynamic PCD. This change try to avoid report this issue again later.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1972
AP calls CollectProcessorData() to collect processor info.
CollectProcessorData function finally calls PcdGetSize function to
get DynamicPCD PcdCpuFeaturesSetting value. PcdGetSize will use
PeiServices table which caused below assert info:
Processor Info: Package: 1, MaxCore : 4, MaxThread: 1
Package: 0, Valid Core : 4
ASSERT [CpuFeaturesPei] c:\projects\jsl\jsl_v1193\Edk2\MdePkg\Library
\PeiServicesTablePointerLibIdt\PeiServicesTablePointer.c(48):
PeiServices != ((void *) 0)
This change uses saved global pcd size instead of calls PcdGetSize to
fix this issue.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1968
The new VS2012 build failure is caused by 7a0df26.
xxx\registercpufeatureslib\dxeregistercpufeatureslib.c(258) :
warning C4701: potentially uninitialized local variable 'MpEvent' used
It is a false positive alarm.
MpEvent is assigned at line 238 and will be used at line 258, both
lines are controlled by "if (CpuFeaturesData->NumberOfCpus > 1)".
This patch initializes MpEvent to suppress incorrect compiler/analyzer
warnings.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1961
Enhance Ppin code to enable and unlock for TRUE State,
and disable and lock for FALSE State.
Note: enable and lock could not be set both.
According to SDM, once Enable_PPIN is set, attempt to write
1 to LockOut will cause #GP, and writing 1 to LockOut is
permitted only if Enable_PPIN is clear.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1968
We met assertion like below, it happens when there is only
one processor.
ASSERT_EFI_ERROR (Status = Not started)
ASSERT [CpuFeaturesDxe] X:\XXX\XXX\RegisterCpuFeaturesLib\
DxeRegisterCpuFeaturesLib.c(149): !EFI_ERROR (Status)
The code should not call StartupAllAPs when there is only one processor.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1934
0x0 MicrocodeBegin MicrocodeEntry MicrocodeEnd 0xffffffff
|--------------|---------------|---------------|---------------|
valid TotalSize
TotalSize is only valid between 0 and (MicrocodeEnd - MicrocodeEntry).
So add '(UINTN)MicrocodeEntryPoint > (MAX_ADDRESS - TotalSize)' before
'((UINTN)MicrocodeEntryPoint + TotalSize) > MicrocodeEnd' to make sure
((UINTN)MicrocodeEntryPoint + TotalSize) wouldn't overflow.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch fixes the bug that the memory under 1MB is modified by
firmware in S3 boot.
Root cause is a racing condition in MpInitLib:
1. BSP: WakeUpByInitSipiSipi is set by NotifyOnS3SmmInitDonePpi()
2. BSP: WakeUpAP() wakes all APs to run certain procedure.
2.1. AllocateResetVector() uses <1MB memory for wake up vector.
2.1. FillExchangeInfoData() resets NumApsExecuting to 0.
2.2. WaitApWakeup() waits AP to clear WAKEUP_AP_SIGNAL.
3. AP: ApWakeupFunction() clears WAKEUP_AP_SIGNAL to inform BSP.
5. BSP: FreeResetVector() restores the <1MB memory
4. AP: ApWakeupFunction() calls the certain procedure.
4.1. NumApsExecuting is decreased.
#4.1 happens after the 1MB memory is restored so the result is
memory below 1MB is changed by #4.1
It happens only when the AP executes procedure a bit longer.
AP returns back to ApWakeupFunction() from procedure after
BSP restores the <1MB memory.
Since NumApsExecuting is only used when InitFlag == ApInitConfig
for counting the processor count.
The patch moves the NumApsExecuting decrease to the path when
InitFlag == ApInitConfig.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Nandagopal Sathyanarayanan <nandagopal.sathyanarayanan@intel.com>
NumApsExecuting is only used when InitFlag == ApInitConfig for
counting the processor count.
The patch changes Ia32 version of waking up vector assembly code
to align to x64 version of waking up vector assembly code.
After the change both versions of waking up vector increase
NumApsExecuting when InitFlag == ApInitConfig.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1810
This patch covers two problems.
1. Current code gets CPUID_THERMAL_POWER_MANAGEMENT in
ClockModulationInitialize() and uses its ECMD bit for all processors.
But ClockModulationInitialize() is only executed by BSP, that means
the bit is just for BSP.
It may have no functionality issue as all processors may have same
bit value in a great possibility. But for good practice, the code
should get CPUID_THERMAL_POWER_MANAGEMENT in ClockModulationSupport
(executed by all processors), and then use them in
ClockModulationInitialize() for all processors.
We can see that Aesni.c (and others) have used this good practice.
2. Current code uses 3 CPU_REGISTER_TABLE_WRITE_FIELD for
MSR_IA32_CLOCK_MODULATION in ClockModulationInitialize(), they can
be reduced to 1 CPU_REGISTER_TABLE_WRITE64 by getting
MSR_IA32_CLOCK_MODULATION for all processors in
ClockModulationSupport() and then update fields for register table
write in ClockModulationInitialize().
We may argue that there may be more times of MSR_IA32_CLOCK_MODULATION
getting. But actually the times of MSR_IA32_CLOCK_MODULATION getting
could be also reduced.
The reason is in ProgramProcessorRegister() of CpuFeaturesInitialize.c,
AsmMsrBitFieldWrite64 (AsmReadMsr64 + AsmWriteMsr64) will be used for
CPU_REGISTER_TABLE_WRITE_FIELD, and AsmWriteMsr64 will be used for
CPU_REGISTER_TABLE_WRITE64.
The times of MSR accessing could be reduced with this patch.
Without the patch:
3 CPU_REGISTER_TABLE_WRITE_FIELD (in ClockModulationInitialize)
==> 3 AsmMsrBitFieldWrite64
==> 3 AsmReadMsr64 + 3 AsmWriteMsr64
With the patch:
1 AsmReadMsr64 (in ClockModulationSupport) +
1 CPU_REGISTER_TABLE_WRITE64 (in ClockModulationInitialize)
==> 1 AsmWriteMsr64
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1829
There will be ASSERT if LMCE is supported as below.
DXE_ASSERT!: [CpuFeaturesDxe]
XXX\UefiCpuPkg\Library\CpuCommonFeaturesLib\MachineCheck.c (342):
ConfigData != ((void *) 0)
The code should get Config Data and FeatureControlGetConfigData
could be used.
This issue is there since the code was added at the commit below.
Revision: 3d6275c113
Date: 2017/8/4 8:46:41
UefiCpuPkg CpuCommonFeaturesLib: Enable LMCE feature.
The commits below are also related to move the code.
Revision: 0233871442
Date: 2017/9/1 10:12:38
UefiCpuPkg/Lmce.c Remove useless file.
Revision: 306a5bcc6b
Date: 2017/8/17 11:40:38
UefiCpuPkg/CpuCommonFeaturesLib: Merge machine check code to same file.
So, the code may not be tested at all on a platform
that supports LMCE.
BTW: A typo in LmceInitialize is also fixed.
The typo is introduced by the commit below.
Revision: d28daaddb3
Date: 2018/10/17 9:24:05
UefiCpuPkg/CpuCommonFeaturesLib: Register MSR base on scope Info.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1808
In current code, the values of TopaEntryPtr->Uint64 for TopaTable
and the values of OutputBaseReg.Uint64 and OutputMaskPtrsReg.Uint64
to register table write for RTIT_OUTPUT_BASE and RTIT_OUTPUT_MASK_PTRS
are not been initialized in whole. For example, the reserved bits in
OutputBaseReg.Uint64 are random that will cause GP fault like below
when SetProcessorRegister (in CpuFeaturesInitialize.c) sets register
based on register table.
!!!! X64 Exception Type - 0D(#GP - General Protection)
CPU Apic ID - 00000000 !!!!
ExceptionData - 0000000000000000
RIP -0000000064D69576, CS -0000000000000038, RFLAGS -0000000000010246
RAX -000000006B9F1001, RCX -0000000000000560, RDX -0000000000000000
RBX -0000000064EECA18, RSP -000000006CB82BA0, RBP -0000000000000008
RSI -0000000080000000, RDI -0000000000000011
R8 -000000006B9493D0, R9 -0000000000000010, R10 -00000000000000FF
R11 -000000006CB82A50, R12 -0000000064D70F50, R13 -0000000066547050
R14 -0000000064E3E198, R15 -0000000000000000
DS -0000000000000030, ES -0000000000000030, FS -0000000000000030
GS -0000000000000030, SS -0000000000000030
CR0 -0000000080010013, CR2 -0000000000000000, CR3 -000000006C601000
CR4 -0000000000000628, CR8 -0000000000000000
DR0 -0000000000000000, DR1 -0000000000000000, DR2 -0000000000000000
DR3 -0000000000000000, DR6 -00000000FFFF0FF0, DR7 -0000000000000400
GDTR -000000006B8CCF18 0000000000000047, LDTR -0000000000000000
IDTR -000000006687E018 0000000000000FFF, TR -0000000000000000
FXSAVE_STATE -000000006CB82800
And current code gets MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_OUTPUT_BASE and
MSR_IA32_RTIT_OUTPUT_MASK_PTRS in ProcTraceInitialize() and uses their
values for all processors. But ProcTraceInitialize() is only executed
by BSP, that means the values just for BSP. For good practice, the code
should get MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_OUTPUT_BASE and
MSR_IA32_RTIT_OUTPUT_MASK_PTRS in ProcTraceSupport (executed by all
processors), and then use them in ProcTraceInitialize() for all
processors. This can also resolve the issue that the values of
OutputBaseReg.Uint64 and OutputMaskPtrsReg.Uint64 are not been
initialized in whole.
For TopaEntryPtr->Uint64, this patch updates code to initialize it
in whole explicitly by TopaEntryPtr->Uint64 = 0 before updating its
fields.
At the same time, this patch also eliminates the ProcTraceSupported
field in PROC_TRACE_PROCESSOR_DATA and the TopaMemArrayCount field in
PROC_TRACE_DATA.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1809
Current code disables TraceEn at the end of ProcTraceInitialize(),
then there will be much memory allocated even when ProcTrace feature
is disabled.
This patch updates code to disable TraceEn and return at the beginning
of ProcTraceInitialize() when when ProcTrace feature is disabled.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1679
The checking to CpuInfo->CpuIdVersionInfoEcx.Bits.AESNI is enough,
the checking to CPU generation could be removed, then the code
could be reused by more platforms.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
These files have \r\n line endings, but a few lines use \r\r\n which
is not a valid line ending. These lines were causing problems for git
and other tools.
Signed-off-by: Joe Richey <joerichey@google.com>
Review-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add a new instance of the MpInitLib that is designed for
uniprocessor platforms that require the use of modules
that depend on the MP_SERVICES_PROTOCOL for dispatch
or to retrieve information about the boot processor.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
GetProcessorLocation2ByApicId() extracts the
package/die/tile/module/core/thread ID from the initial APIC ID.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Zhiqiang Qin <zhiqiang.qin@intel.com>
Cc: Ray Ni <Ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
PcdCpuFeaturesSupport used to specify the platform policy about
what CPU features this platform supports. This PCD will be used
in IsCpuFeatureSupported only.
Now RegisterCpuFeaturesLib use this PCD as an template to Get the
pcd size. Update the code logic to replace it with
PcdCpuFeaturesSetting.
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1375
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
PcdCpuFeaturesUserConfiguration.
Merge PcdCpuFeaturesUserConfiguration into PcdCpuFeaturesSetting.
Use PcdCpuFeaturesSetting as input for the user input feature setting
Use PcdCpuFeaturesSetting as output for the final CPU feature setting
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1375
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
V2 changes:
Update the commit message and comments in the code.
When waking vector buffer allocated by CpuDxe is tested by MemTest86
in MP mode, an error is reported because the same range of memory is
modified by both CpuDxe driver and MemTest86.
The waking vector buffer is not expected to be tested by MemTest86 if
it is allocated out because MemTest86 only tests free memory. But
current CpuDxe driver "borrows" buffer instead of allocate buffer for
waking vector buffer (through allocate & free to get the buffer
pointer, backup the buffer data before using it and restore it after
using). With this implementation, if the buffer borrowed is not used
by any other drivers, MemTest86 tool will treat it as free memory
and test it.
In order to fix the above issue, CpuDxe changes to allocate the
buffer below 1M instead of borrowing it. But directly allocating
memory below 1MB causes LegacyBios driver fails to start. LegacyBios
driver allocates memory range from
"0xA0000 - PcdEbdaReservedMemorySize" to 0xA0000 as Ebda Reserved
Memory. The minimum value for "0xA0000 - PcdEbdaReservedMemorySize"
is 0x88000. If LegacyBios driver allocate this range failed, it
asserts.
LegacyBios also reserves range from 0x60000 to
"0x60000 + PcdOpromReservedMemorySize", it will be used as Oprom
Reserve Memory. The maximum value for "0x60000 +
PcdOpromReservedMemorySize" is 0x88000. LegacyBios driver tries to
allocate these range page(4K size) by page. It just reports warning
message if some pages are already allocated by others.
Base on above investigation, one page in range 0x60000 ~ 0x88000 can
be used as the waking vector buffer.
LegacyBios driver only reports warning when page allocation in range
[0x60000, 0x88000) fails. This library is consumed by CpuDxe driver
to produce CPU Arch protocol. LagacyBios driver depends on CPU Arch
protocol which guarantees below allocation runs earlier than
LegacyBios driver.
Cc: Ray Ni <ray.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1621
According to Intel SDM as below, the BIT0 should be treated as
lock bit, and BIT1 should be treated as disable(1)/enable(0) bit.
"11b: AES instructions are not available until next
RESET.
Otherwise, AES instructions are available.
If the configuration is not 01b, AES
instructions can be mis-configured if a privileged agent
unintentionally writes 11b"
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
Should make sure the TotalSize of Microcode is aligned with 4 bytes
before calling CalculateSum32 function.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
The Microcode region indicated by MicrocodePatchAddress PCD may contain
more than one Microcode entry. We should save InCompleteCheckSum32 value
for each payload. Move the logic for calculate InCompleteCheckSum32 from
the outsize of the do-while loop to the inside.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1576
The root cause of this issue is that non-stop mode of Heap Guard and
NULL Detection set TF bit (single-step) in EFLAG unconditionally in
the common handler in CpuExceptionLib.
If PcdCpuSmmStaticPageTable is FALSE, the SMM will only create page
table for memory below 4G. If SMM tries to access memory beyond 4G,
a page fault exception will be triggered and the memory to access
will be added to page table so that SMM code can continue the access.
Because of above issue, the TF bit is set after the page fault is
handled and then fall into another DEBUG exception. Since non-stop
mode of Heap Guard and NULL Detection are not enabled, no special
DEBUG exception handler is registered. The default handler just
prints exception context and go into dead loop.
Actually EFLAGS can be changed in any standard exception handler.
There's no need to do single-step setup in assembly code. So the fix
is to move the logic to C code part of page fault exception handler
so that we can fully validate the configuration and prevent TF bit
from being set unexpectedly.
Fixes: dcc026217f16b918bbaf
Test:
- Pass special test of accessing memory beyond 4G in SMM mode
- Boot to OS with Qemu emulator platform (Fedora27, Ubuntu18.04,
Windows7, Windows10)
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1521
Add information dump for Control Protection exception.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Yao Jiewen <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
The following Microcode payload format is define in SDM spec.
Payload: |MicrocodeHeader|MicrocodeBinary|ExtendedHeader|ExtendedTable|.
When we verify the CheckSum32 with ExtendedTable, we should use the fields
of ExtendedTable to replace corresponding fields in MicrocodeHeader,
and then calculate the CheckSum32 with MicrocodeHeader+MicrocodeBinary.
This patch already verified on ICL platform.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Zhang Chao B <chao.b.zhang@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1481
Today's MtrrLib contains a bug, for example:
when the original cache setting is WB for [0xF_0000, 0xF_8000) and,
a new request to set [0xF_0000, 0xF_4000) to WP,
the cache setting for [0xF_4000, 0xF_8000) is reset to UC.
The reason is when MtrrLibSetBelow1MBMemoryAttribute() is called the
WorkingFixedSettings doesn't contain the actual MSR value stored in
hardware, but when writing the fixed MTRRs, the code logic assumes
WorkingFixedSettings contains the actual MSR value.
The new fix is to change MtrrLibSetBelow1MBMemoryAttribute() to
calculate the correct ClearMasks[] and OrMasks[], and use them
directly when writing the fixed MTRRs.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Chasel Chiu <chasel.chiu@intel.com>
In AcquireSpinLock function, it may call GetPerformanceCounter which
final calls PeiService table. This code may also been used by AP but
AP should not calls PeiService. This patch update code to avoid use
AcquireSpinLock function.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1411
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
V3:
Define union to specify the ppi or protocol.
V2:
1. Initialize CpuFeaturesData->MpService in CpuInitDataInitialize
and make this function been called at the begin of the
initialization.
2. let all other functions use CpuFeaturesData->MpService install
of locate the protocol itself.
V1:
GetProcessorIndex function calls GetMpPpi to get the MP Ppi.
Ap will calls GetProcessorIndex function which final let AP calls
PeiService.
This patch avoid GetProcessorIndex call PeiService.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1411
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Enhance debug message format to let them easy to read.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1411
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1091
Previously, when compiling NASM source files, BaseTools did not support
including files outside of the NASM source file directory. As a result, we
duplicated multiple copies of "StuffRsb.inc" files in UefiCpuPkg. Those
INC files contain the common logic to stuff the Return Stack Buffer and
are identical.
After the fix of BZ 1085:
https://bugzilla.tianocore.org/show_bug.cgi?id=1085
The above support was introduced.
Thus, this commit will merge all the StuffRsb.inc files in UefiCpuPkg into
one file. The merged file will be named 'StuffRsbNasm.inc' and be placed
under folder UefiCpuPkg/Include/.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
*Excpetion* should be *Exception*
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Mike Maslenkin <mike.maslenkin@gmail.com>
CC: Eric Dong <eric.dong@intel.com>
CC: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1305
The patch reverts commit 1ed6498c4a
* UefiCpuPkg/CommonFeature: Skip locking when the feature is disabled
FEATURE_CONTROL.Lock bit is controlled by feature
CPU_FEATURE_LOCK_FEATURE_CONTROL_REGISTER. The commit 1ed649 fixes
a bug that when the feature is disabled, the Lock bit is cleared.
But it's a security hole if the bit is cleared when booting OS.
We can argue that platform needs to make sure the value
of PcdCpuFeaturesUserConfiguration should be set properly to make
sure feature CPU_FEATURE_LOCK_FEATURE_CONTROL_REGISTER is enabled.
But it's better to guarantee this in the generic core code.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
In current implementation, core and package level sync uses same semaphores.
Sharing the semaphore may cause wrong execution order.
For example:
1. Feature A has CPU_FEATURE_CORE_BEFORE dependency with Feature B.
2. Feature C has CPU_FEATURE_PACKAGE_AFTER dependency with Feature B.
The expected feature initialization order is A B C:
A ---- (Core Depends) ----> B ---- (Package Depends) ----> C
For a CPU has 1 package, 2 cores and 4 threads. The feature initialization
order may like below:
Thread#1 Thread#2 Thread#3 Thread#4
[A.Init] [A.Init] [A.Init]
Release(S1, S2) Release(S1, S2) Release(S3, S4)
Wait(S1) * 2 Wait(S2) * 2 <------------------------------- Core sync
[B.Init] [B.Init]
Release (S1,S2,S3,S4)
Wait (S1) * 4 <----------------------------------------------------- Package sync
Wait(S4 * 2) <- Core sync
[B.Init]
In above case, for thread#4, when it syncs in core level, Wait(S4) * 2 isn't
blocked and [B.Init] runs. But [A.Init] hasn't run in thread#3. It's wrong!
Thread#4 should execute [B.Init] after thread#3 executes [A.Init] because B
core level depends on A.
The reason of the wrong execution order is that S4 is released in thread#1
by calling Release (S1, S2, S3, S4) and in thread #4 by calling
Release (S3, S4).
To fix this issue, core level sync and package level sync should use separate
semaphores.
In above example, the S4 released in Release (S1, S2, S3, S4) should not be the
same semaphore as that in Release (S3, S4).
Related BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1311
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
V2 changes:
V1 change has regression which caused by change feature order.
V2 changes logic to detect dependence not only for the
neighborhood features. It need to check all features in the list.
V1 Changes:
In current code logic, only adjust feature position if current
CPU feature position not follow the request order. Just like
Feature A need to be executed before feature B, but current
feature A registers after feature B. So code will adjust the
position for feature A, move it to just before feature B. If
the position already met the requirement, code will not adjust
the position.
This logic has issue when met all below cases:
1. feature A has core or package level dependence with feature B.
2. feature A is register before feature B.
3. Also exist other features exist between feature A and B.
Root cause is driver ignores the dependence for this case, so
threads may execute not follow the dependence order.
Fix this issue by change code logic to adjust feature position
for CPU features which has dependence relationship.
Related BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1311
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1305
Today's code unconditionally sets the IA32_FEATURE_CONTROL.Lock to 1
no matter the feature is enabled or not.
The patch fixes this issue by only setting the Lock bit to 1 when
the feature is enabled.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
In some special cases, after BSP sends Init-sipi-sipi signal
AP needs more time to start the Ap procedure. In this case
BSP may think AP has finished its task but in fact AP hasn't began
yet.
Rollback former change to keep the status which only be used
when AP really finished task.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Build UefiCpuPkg with below configuration:
Architecture(s) = IA32
Build target = NOOPT
Toolchain = VS2015x86
Below error info shows up:
DxeRegisterCpuFeaturesLib.lib(CpuFeaturesInitialize.obj) :
error LNK2001: unresolved external symbol __allmul
Valid mDependTypeStr type only have 5 items, use UINT32 type cast
to fix this error.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Index is initialized to MAX_UINT16 as default failure value, which
is what the ASSERT is supposed to test for. The ASSERT condition
however can never return FALSE for INT16 != int, as due to
Integer Promotion[1], Index is converted to int, which can never
result in -1.
Furthermore, Index is used as a for loop index variable inbetween its
initialization and the ASSERT, so the value is unconditionally
overwritten too.
Fix the ASSERT check to compare Index to its upper boundary, which it
will be equal to if the loop was not broken out of on success.
[1] ISO/IEC 9899:2011, 6.5.9.4
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marvin Haeuser <Marvin.Haeuser@outlook.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Current code assume only one dependence (before or after) for one
feature. Enhance code logic to support feature has two dependence
(before and after) type.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Changes include:
1. Remove extra white space at the end of line.
2. Add comments for the new add function parameter.
3. Update IN OUT tag for function parameter.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Remove extra white space at the end of line.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Code initialized in function can't be correctly detected by build tool.
Add code to clearly initialize the local variable before use it.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Because MSR has scope attribute, driver has no needs to set
MSR for all APs if MSR scope is core or package type. This patch
updates code to base on the MSR scope value to add MSR to the register
table.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
V4 changes include:
1. Serial debug message for different threads when program the register table.
V3 changes include:
1. Use global variable instead of internal function to return string for register type
and dependence type.
2. Add comments for some complicated logic.
V2 changes include:
1. Add more description for the code part which need easy to understand.
2. Refine some code base on feedback for V1 changes.
V1 changes include:
In a system which has multiple cores, current set register value task costs huge times.
After investigation, current set MSR task costs most of the times. Current logic uses
SpinLock to let set MSR task as an single thread task for all cores. Because MSR has
scope attribute which may cause GP fault if multiple APs set MSR at the same time,
current logic use an easiest solution (use SpinLock) to avoid this issue, but it will
cost huge times.
In order to fix this performance issue, new solution will set MSRs base on their scope
attribute. After this, the SpinLock will not needed. Without SpinLock, new issue raised
which is caused by MSR dependence. For example, MSR A depends on MSR B which means MSR A
must been set after MSR B has been set. Also MSR B is package scope level and MSR A is
thread scope level. If system has multiple threads, Thread 1 needs to set the thread level
MSRs and thread 2 needs to set thread and package level MSRs. Set MSRs task for thread 1
and thread 2 like below:
Thread 1 Thread 2
MSR B N Y
MSR A Y Y
If driver don't control execute MSR order, for thread 1, it will execute MSR A first, but
at this time, MSR B not been executed yet by thread 2. system may trig exception at this
time.
In order to fix the above issue, driver introduces semaphore logic to control the MSR
execute sequence. For the above case, a semaphore will be add between MSR A and B for
all threads. Semaphore has scope info for it. The possible scope value is core or package.
For each thread, when it meets a semaphore during it set registers, it will 1) release
semaphore (+1) for each threads in this core or package(based on the scope info for this
semaphore) 2) acquire semaphore (-1) for all the threads in this core or package(based
on the scope info for this semaphore). With these two steps, driver can control MSR
sequence. Sample code logic like below:
//
// First increase semaphore count by 1 for processors in this package.
//
for (ProcessorIndex = 0; ProcessorIndex < PackageThreadsCount ; ProcessorIndex ++) {
LibReleaseSemaphore ((UINT32 *) &SemaphorePtr[PackageOffset + ProcessorIndex]);
}
//
// Second, check whether the count has reach the check number.
//
for (ProcessorIndex = 0; ProcessorIndex < ValidApCount; ProcessorIndex ++) {
LibWaitForSemaphore (&SemaphorePtr[ApOffset]);
}
Platform Requirement:
1. This change requires register MSR setting base on MSR scope info. If still register MSR
for all threads, exception may raised.
Known limitation:
1. Current CpuFeatures driver supports DXE instance and PEI instance. But semaphore logic
requires Aps execute in async mode which is not supported by PEI driver. So CpuFeature
PEI instance not works after this change. We plan to support async mode for PEI in phase
2 for this task.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1237
Sometimes the memory will be contaminated by random data left in last
boot (warm reset). The code should not assume the allocated memory is
always filled with zero. This patch add code to clear data structure
used for stack switch to prevent such problem from happening.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The PCD below is unused, so it has been removed from inf.
gUefiCpuPkgTokenSpaceGuid.PcdCpuFeaturesSupport
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: shenglei <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1187
The patch reverts 9c8c4478cf
"UefiCpuPkg/MtrrLib: Skip Base MSR access when the pair is invalid".
Microsoft Windows will report an error in event manager if MTRR
usage is different across hibernate even when the difference is
in an non valid MTRR pair. This seems like a bug in Windows but
for compatibility and servicing reasons we think a change in UEFI
would wise.
A Windows change has already been submitted for the next iteration
(2019 time frame).
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
The conflict issues are introduced by Stack Guard feature enabled for
PEI.
The first is CR0 which should be restored after CR3 and CR4.
Another is TR which should not be passed from BSP to AP during init
phase.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: "Ware, Ryan R" <ryan.r.ware@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Stack Guard needs to setup stack switch capability to allow exception
handler to be called with good stack if stack overflow is detected.
This patch update InitializeCpuExceptionHandlersEx() to allow pass
extra initialization data used to setup exception stack switch for
specified exceptions.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: "Ware, Ryan R" <ryan.r.ware@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Fix trailing white spaces and invalid line ending issue.
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
When an exception happens in AP, system hangs at
GetPeiServicesTablePointer(), complaining the PeiServices retrieved
from memory before IDT is NULL.
Due to the following commit:
c563077a38
* UefiCpuPkg/MpInitLib: Avoid calling PEI services from AP
the IDT used by AP no longer preserve PeiServices pointer in the
very beginning.
But the implementation of PeiExceptionHandlerLib still assumes
the PeiServices pointer is there, so the assertion happens.
The patch fixes the exception handler library to not call
PEI services from AP.
The patch duplicates the #0 exception stub header in an allocated
pool but with extra 4-byte/8-byte to store the exception handler
data which was originally stored in HOB.
When AP exception happens, the code gets the exception handler data
from the exception handler for #0.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Fan Jeff <vanjeff_919@hotmail.com>
Today's implementation of handling HOOK_BEFORE and HOOK_AFTER is
a bit complex. More comments is better.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Fan Jeff <vanjeff_919@hotmail.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Once the #PF handler has set the page to be 'present', there should
be a way to reset it to 'not-present'. 'TF' bit in EFLAGS can be used
for this purpose. 'TF' bit will be set in interrupted function context
so that it can be triggered once the cpu control returns back to the
instruction causing #PF and re-execute it.
This is an necessary step to implement non-stop mode for Heap Guard
and NULL Pointer Detection feature.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1093
Return Stack Buffer (RSB) is used to predict the target of RET
instructions. When the RSB underflows, some processors may fall back to
using branch predictors. This might impact software using the retpoline
mitigation strategy on those processors.
This commit will add RSB stuffing logic before returning from SMM (the RSM
instruction) to avoid interfering with non-SMM usage of the retpoline
technique.
After the stuffing, RSB entries will contain a trap like:
@SpecTrap:
pause
lfence
jmp @SpecTrap
A more detailed explanation of the purpose of commit is under the
'Branch target injection mitigation' section of the below link:
https://software.intel.com/security-software-guidance/insights/host-firmware-speculative-execution-side-channel-mitigation
Please note that this commit requires further actions (BZ 1091) to remove
the duplicated 'StuffRsb.inc' files and merge them into one under a
UefiCpuPkg package-level directory (such as UefiCpuPkg/Include/).
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1091
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
V1 changes:
> Current code logic can't confirm CpuS3DataDxe driver start before
> CpuFeaturesDxe driver. So the assumption in CpuFeaturesDxe not valid.
> Add implementation for AllocateAcpiCpuData function to remove this
> assumption.
V2 changes:
> Because CpuS3Data memory will be copy to smram at SmmReadToLock point,
> so the memory type no need to be ACPI NVS type, also the address not
> limit to below 4G.
> This change remove the limit of ACPI NVS memory type and below 4G.
V3 changes:
> Remove function definition in header file.
> Add STATIC in function implementation.
Pass OS boot and resume from S3 test.
Bugz: https://bugzilla.tianocore.org/show_bug.cgi?id=959
Reported-by: Marvin Häuser <Marvin.Haeuser@outlook.com>
Suggested-by: Fan Jeff <vanjeff_919@hotmail.com>
Cc: Marvin Häuser <Marvin.Haeuser@outlook.com>
Cc: Fan Jeff <vanjeff_919@hotmail.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Merge [Sources.Ia32, Sources.X64] to [Sources] after removing IPF. Also
change other similar parts in this file.
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Base on UEFI spec requirement, StartAllAPs function should not use the APs which has been disabled before. This patch just change current code to follow this rule.
V3 changes:
Only called by StartUpAllAps, WakeUpAp will not wake up the disabled APs, in other cases also need to include the disabled APs, such as CpuDxe driver start up and ChangeApLoopCallback function.
WakeUpAP() is called with (Broadcast && WakeUpDisabledAps) from MpInitLibInitialize(), CollectProcessorCount() and MpInitChangeApLoopCallback() only. The first two run before the PPI or Protocol user has a chance to disable any APs. The last one runs in response to the ExitBootServices and LegacyBoot events, after which the MP protocol is unusable. For this reason, it doesn't matter that an originally disabled AP's state is not restored to Disabled, when
WakeUpAP() is called with (Broadcast && WakeUpDisabledAps).
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
The patch includes below changes:
(1) It removes "volatile" from RunningCount, because only the BSP modifies it.
(2) When we detect a timeout in CheckAllAPs(), and collect the list of failed CPUs, the size of the list is derived from the following difference, before the patch:
StartCount - FinishedCount
where "StartCount" is set by the BSP at startup, and FinishedCount is incremented by the APs themselves.
Here the patch replaces this difference with
StartCount - RunningCount
that is, the difference is no more calculated from the BSP's startup counter and the AP's shared finish counter, but from the RunningCount measurement that the BSP does itself, in CheckAllAPs().
(3) Finally, the patch changes the meaning of RunningCount. Before the patch, we have:
- StartCount: the number of APs the BSP stars up,
- RunningCount: the number of finished APs that the BSP collected
After the patch, StartCount is removed, and RunningCount is *redefined* as the following difference:
OLD_StartCount - OLD_RunningCount
Giving the number of APs that the BSP started up but hasn't collected yet.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Current CPU state definition include CpuStateIdle and CpuStateFinished.
After investigation, current code can use CpuStateIdle to replace the
CpuStateFinished. It will reduce the state number and easy for maintenance.
> Before this patch, the state transitions for an AP are:
>
> Idle ----> Ready ----> Busy ----> Finished ----> Idle
> [BSP] [AP] [AP] [BSP]
>
> After the patch, the state transitions for an AP are:
>
> Idle ----> Ready ----> Busy ----> Idle
> [BSP] [AP] [AP]
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Current function has low performance because it calls GetApicId
in the loop, so it maybe called more than once.
New logic call GetApicId once and base on this value to search
the processor.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <vanjeff_919@hotmail.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
When resume from S3 and CPU loop mode is MWait mode,
if driver calls APs to do task at EndOfPei point, the
APs can't been wake up and bios hang at that point.
The root cause is PiSmmCpuDxeSmm driver wakes up APs
with HLT mode during S3 resume phase to do SMM relocation.
After this task, PiSmmCpuDxeSmm driver not restore APs
context which make CpuMpPei driver saved wake up buffer
not works.
The solution for this issue is let CpuMpPei driver hook
S3SmmInitDone ppi notification. In this notify function,
it check whether Cpu Loop mode is not HLT mode. If yes,
CpuMpPei driver will set a flag to force BSP use INIT-SIPI
-SIPI command to wake up the APs.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The SDM requires only one thread per core to load the
microcode.
This change enables this solution.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Search uCode costs much time, if AP has same processor type
with BSP, AP can use BSP saved uCode info to get better performance.
This change enables this solution.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Read uCode from memory has better performance than from flash.
But it needs extra effort to let BSP copy uCode from flash to
memory. Also BSP already enable cache in SEC phase, so it use
less time to relocate uCode from flash to memory. After
verification, if system has more than one processor, it will
reduce some time if load uCode from memory.
This change enable this optimization.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Today's MpInitLib PEI implementation directly calls
PeiServices->GetHobList() from AP which may cause racing issue.
This patch fixes this issue by duplicating IDT for APs.
Because CpuMpData structure is stored just after IDT, the CpuMPData
address equals to IDTR.BASE + IDTR.LIMIT + 1.
v2:
1. Add ALIGN_VALUE() on BufferSize.
2. Add ASSERT() to make sure no memory usage outside of the allocated buffer.
3. Add more comments in InitConfig path when restoring CpuData[0].VolatileRegisters.
Cc: Jeff Fan <vanjeff_919@hotmail.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Fish Andrew <afish@apple.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Removing rules for Ipf sources file:
* Remove the source file which path with "ipf" and also listed in
[Sources.IPF] section of INF file.
* Remove the source file which listed in [Components.IPF] section
of DSC file and not listed in any other [Components] section.
* Remove the embedded Ipf code for MDE_CPU_IPF.
Removing rules for Inf file:
* Remove IPF from VALID_ARCHITECTURES comments.
* Remove DXE_SAL_DRIVER from LIBRARY_CLASS in [Defines] section.
* Remove the INF which only listed in [Components.IPF] section in DSC.
* Remove statements from [BuildOptions] that provide IPF specific flags.
* Remove any IPF sepcific sections.
Removing rules for Dec file:
* Remove [Includes.IPF] section from Dec.
Removing rules for Dsc file:
* Remove IPF from SUPPORTED_ARCHITECTURES in [Defines] section of DSC.
* Remove any IPF specific sections.
* Remove statements from [BuildOptions] that provide IPF specific flags.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
1. Do not use tab characters
2. No trailing white space in one line
3. All files must end with CRLF
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
On AMD processors the second SendIpi in the SendInitSipiSipi and
SendInitSipiSipiAllExcludingSelf routines is not required, and may cause
undesired side-effects during MP initialization.
This patch leverages the StandardSignatureIsAuthenticAMD check to exclude
the second SendIpi and its associated MicroSecondDelay (200).
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Leo Duran <leo.duran@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
NASM has replaced ASM and S files.
1. Remove ASM from all modules expect for the ones in ResetVector directory.
The ones in ResetVector directory are included by Vtf0.nasmb. They are
also nasm style.
2. Remove S files from the drivers only.
3. https://bugzilla.tianocore.org/show_bug.cgi?id=881
After NASM is updated, S files can be removed from Library.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
According to IA manual:
"Before setting this bit (MSR_IA32_MISC_ENABLE[22]) , BIOS must
execute the CPUID.0H and examine the maximum value returned in
EAX[7:0]. If the maximum value is greater than 2, this bit is
supported."
We need to fix our current detection logic to compare against 2.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Ming Shao <ming.shao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Ray Ni
Laszlo Ersek
John E Lofgren
Donald Kuo
Dong, Eric
Star Zeng
Zhichao Gao
Joe Richey
Michael D Kinney
Shenglei Zhang
Chen A Chen
Jian J Wang
Jiewen Yao
Ruiyu Ni
Hao Wu
Mike Maslenkin
Marvin H?user
Liming Gao