When both the PEI and DXE phases operate in the same execution
mode(32-bit/64-bit), the BSP send a special start-up signal during
the DXE phase to awaken the Application APs.
To eliminate the need for the INIT-SIPI-SIPI sequence at the beginning
of the DXE phase, the BSP call the SwitchApContext function to trigger
the special start-up signal. By writing the specified
StartupSignalValue to the designated StartupSignalAddress, the BSP
wakes up the APs from mwait mode. Once the APs receive the
MP_HAND_OFF_SIGNAL value, they are awakened and proceed to execute the
SwitchContextPerAp procedure. They enter another while loop,
transitioning their context from the PEI phase to the DXE phase.
The original state transitions for an AP during the procedure are as
follows:
Idle ----> Ready ----> Busy ----> Idle
[BSP] [AP] [AP]
Instead of init-sipi-sipi sequence, we make use of a
start-up signal to awaken the APs and transfer their context from
PEI to DXE. Consequently, APs, rather than the BSP, to set their state
to CpuStateReady.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
In the original design, once the APs finished executing their assembly
code and switched to executing C code, they would enter a continuous
loop within a function. In this function, they would collect CpuMpData
using the MP_CPU_EXCHANGE_INFO mechanism. However, in the updated
approach, CpuMpData can now be passed directly to the ApWakeUpFunction,
bypassing the need for MP_CPU_EXCHANGE_INFO. This modification is made
in preparation for eliminating the requirement of a second
INIT-SIPI-SIPI sequence in the DXE phase.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Initially, the purpose of the Hob was twofold: it served as a way to
transfer information from PEI to DXE. However, during the DXE phase,
only a few fields from the CPU_MP_DATA which collected in PEI phase were
needed. A new Hob was specifically created to transfer information
to the DXE phase. This new Hob contained only the essential fields
required for reuse in DXE. For instance, instead of directly including
the BspNumber in MpHandOff, the DXE phase introduced the use of
GetBspNumber() to collect the BspNumber from ApicID and CpuCount.
The SaveCpuMpData() function was updated to construct the MP_HAND_OFF
Hob. Additionally, the function introduced the MP_HAND_OFF_SIGNAL,
which solely served the purpose of awakening the APs
and transitioning their context from PEI to DXE. The
WaitLoopExecutionMode field indicated whether the bit mode of PEI
matched that of DXE. Both of them were filled only if the ApLoopMode
was not ApInHltLoop. In the case of ApInHltLoop, it remained necessary
to wake up the APs using the init-sipi-sipi sequence. This improvement
still allow INIT-SIPI-SIPI even APs are wait in Run/Mwait loop mode.
The function GetMpHandOffHob() was added to facilitate access to the
collected MpHandOff in the DXE phase. The CpuMpData in the DXE phase
was updated by gathering information from MpHandOff. Since MpHandOff
replaced the usage of OldCpuMpData and contained essential information
from the PEI phase to the DXE phase. AmdSevUpdateCpuMpData was included
to maintain the original implementation of AmdSev, ensuring that
OldCpuMpData->NewCpuMpData pointed to CpuMpData.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Refactor the logic for placing APs in
Mwait/Runloop into a separate function.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Refactor the logic for placing APs in HltLoop into a separate function.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
Removes SmmCpuFeaturesReadSaveStateRegister and
SmmCpuFeaturesWirteSaveStateRegister function from
SmmCpuFeaturesLib library.
MmSaveStateLib library replaces the functionality of the above
functions.
Platform old/new need to use MmSaveStateLib library to read/write save
state registers.
Current implementation supports Intel and AMD.
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: Abdul Lateef Attar <abdattar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
Implements MmSaveStateLib library interfaces
to read and write save state
registers for Intel processor family.
Moves Intel and AMD common functionality to common area.
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Abdul Lateef Attar <abdattar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
Implements interfaces to read and write save state
registers of AMD's processor family.
Initializes processor SMMADDR and MASK depends
on PcdSmrrEnable flag.
Program or corrects the IP once control returns from SMM.
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Abdul Lateef Attar <abdattar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
moves Intel-specific code to the arch-dependent file.
Other processor families might have different
implementation of these functions.
Hence, moving out of the common file.
Cc: Abner Chang <abner.chang@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Abdul Lateef Attar <AbdulLateef.Attar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The timer compare register is 64-bit so simplifying the delay
function.
Cc: Andrei Warkentin <andrei.warkentin@intel.com>
Signed-off-by: Tuan Phan <tphan@ventanamicro.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Update ProcTrace feature code to support enable collect performance
data by generating CYC and TSC packets. Add a new dynamic
PCD to indicate if enable performance collecting. In ProcTrace.c
code, if this new PCD is true, after check cpuid, CYC and TSC
packets will be generated by setting the corresponding MSR bits
feilds if supported.
Bugzila: https://bugzilla.tianocore.org/show_bug.cgi?id=4423
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Xiao X Chen <xiao.x.chen@intel.com>
Update code to support enable ProcTrace only on BSP. Add a new
dynamic PCD to indicate if enable ProcTrace only on BSP. In
ProcTrace.c code, if this new PCD is true, only allocate buffer
and set CtrlReg.Bits.TraceEn to 1 for BSP.
Bugzila: https://bugzilla.tianocore.org/show_bug.cgi?id=4423
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Xiao X Chen <xiao.x.chen@intel.com>
Because UefiCpuPkg/UefiCpuLib is merged to MdePkg/CpuLib and all modules
are updated to not depend on this library, remove it completely.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
__FUNCTION__ is a pre-standard extension that gcc and Visual C++ among
others support, while __func__ was standardized in C99.
Since it's more standard, replace __FUNCTION__ with __func__ throughout
UefiCpuPkg.
Signed-off-by: Rebecca Cran <rebecca@bsdio.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
The CPU exception handler library code was rewritten at some point to
populate the vector code templates with absolute references at runtime,
given that the XCODE linker does not permit absolute references in
executable code when creating PIE executables.
This is rather unfortunate, as this prevents us from using strict
permissions on the memory mappings, given that the .text section needs
to be writable at runtime for this arrangement to work.
So let's make this hack XCODE-only, by setting a preprocessor #define
from the command line when using the XCODE toolchain, and only including
the runtime fixup code when the macro is defined.
While at it, rename the Xcode5ExceptionHandlerAsm.nasm source file and
drop the Xcode5 prefix: this code is used by other toolchains too.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The PEI flavor of CpuExceptionHandlerLib never populates more than 32
IDT vectors, and there is no CET shadow stack support in the PEI phase.
So there is no need to use the generic ExceptionHandler NASM source,
which carries a 256-entry template and CET support, and writes to its
own .text section when built using XCODE, which is not permitted in the
PEI phase. So let's switch to the reduced SEC/PEI version of this
component, which is sufficient for PEI and doesn't suffer from the same
issue.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Currently, we use the non-Xcode5 version of ExceptionHandlerAsm.nasm
only for the SEC and PEI phases, and this version was not compatible
with the XCODE or LLD linkers, which do not permit absolute relocations
in read-only sections.
Given that SEC and PEI code typically executes in place from flash and
does not use page alignment for sections, we can simply emit the code
carrying the absolute symbol references into the .data segment instead.
This works around the linker's objections, and the resulting image will
be mapped executable in its entirety anyway. Since this is only needed
for XCODE, let's make this change conditionally using a preprocessor
macro.
Let's rename the .nasm file to reflect the fact that is used for the
SecPei flavor of this library only, and while at it, remove some
unnecessary absolute references.
Also update the Xcode specific version of this library, and use this
source file instead. This is necesessary, as the Xcode specific version
modifies its own code at runtime, which is not permitted in SEC or PEI.
Note that this also removes CET support from the Xcode5 specific build
of the SEC/PEI version of this library, but this is not needed this
early in any case, and this aligns it with other toolchains, which use
this version of the library, which does not have CET support either.
1. Change for non-XCODE SecPeiCpuExceptionHandlerLib:
. Use SecPeiExceptionHandlerAsm.nasm (renamed from
ExceptionHandlerAsm.nasm)
. Removed some unnecessary absolute references
(32 IDT stubs are still in .text.)
2. Change for XCODE SecPeiCpuExceptionHandlerLib:
. Use SecPeiExceptionHandlerAsm.nasm instead of
Xcode5ExceptionHandlerAsm.nasm
. CET logic is not in SecPeiExceptionHandlerAsm.nasm (but aligns to
non-XCODE lib instance)
. Fixed a bug that does runtime fixup in TEXT section in SPI flash.
. Emitted the code carrying the absolute symbol references into the
.data which XCODE or LLD linkers allow.
. Then fixup can be done by other build tools such as GenFv if the code
runs in SPI flash, or by PE coff loader if the code is loaded to
memory.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Drop MtrrLibIsPowerOfTwo function, use the new IS_POW2() macro instead.
The ASSERT() removed (inside MtrrLibIsPowerOfTwo) is superfluous,
another ASSERT() a few lines up in MtrrLibCalculateMtrrs() already
guarantees that Length can not be zero at this point.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4353
Due to AMD erratum #1467, an SEV-SNP VMSA should not be 2MB aligned. To
work around this issue, allocate two pages instead of one. Because of the
way that page allocation is implemented, always try to use the second
page. If the second page is not 2MB aligned, free the first page and use
the second page. If the second page is 2MB aligned, free the second page
and use the first page. Freeing in this way reduces holes in the memory
map.
Fixes: 06544455d0 ("UefiCpuPkg/MpInitLib: Use SEV-SNP AP Creation ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=4353
When parking the APs on exiting from UEFI, a new page allocation is made.
This allocation, however, does not end up being marked reserved in the
memory map supplied to the OS. To avoid this, re-use the VMSA by clearing
the VMSA RMP flag, updating the page contents and re-setting the VMSA RMP
flag.
Fixes: 06544455d0 ("UefiCpuPkg/MpInitLib: Use SEV-SNP AP Creation ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
When TME-MK is enabled, the MtrrLib should substract the TME-MK
reserved bits from the max PA returned from CPUID instruction.
The new test case guarantees such behavior in MtrrLib.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Ahmad Anadani <ahmad.anadani@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
CPUID enumeration of MAX_PA is unaffected by TME-MK activation and
will continue to report the maximum physical address bits available
for software to use, irrespective of the number of KeyID bits.
So, we need to check if TME is enabled and adjust the PA size
accordingly.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Ahmad Anadani <ahmad.anadani@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
MtrrLib code queries the CPUID leaf 7h result if support.
Update Test code temporary to claim the CPUID only
supports max leaf as 1 so MtrrLib skips to query CPUID leaf 7h.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Ahmad Anadani <ahmad.anadani@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
The random test cases just run for too long that may cause timeout
in CI test.
Disable them for now.
Co-authored-by: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Sean Brogan <sean.brogan@microsoft.com>
Reduce the number of random tests. In previous patch, non-1:1
mapping is enbaled and it may need more than an hour and a half
for the CI test, which may lead to CI timeout. Reduce the number
of random test count to pass the CI.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add RandomTest for PAE paging.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Modify CpuPageTableLib code to enable PAE paging.
In PageTableMap() API:
When creating new PAE page table, after creating page table,
set all MustBeZero fields of 4 PDPTE to 0. The MustBeZero
fields are treated as RW and other attributes by the common
map logic. So they might be set to 1.
When updating exsiting PAE page table, the special steps are:
1.Prepare 4K-aligned 32bytes memory in stack for 4 temp PDPTE.
2.Copy original 4 PDPTE to the 4 temp PDPTE and set the RW,
UserSupervisor to 1 and set Nx of 4 temp PDPTE to 0.
4.After updating the page table, set the MustBeZero fields of
4 temp PDPTE to 0.
5.Copy the temp PDPTE to original PDPTE.
In PageTableParse() API, also create 4 temp PDPTE in stack.
Copy original 4 PDPTE to the 4 temp PDPTE. Then set the RW,
UserSupervisor to 1 and set Nx of 4 temp PDPTE to 0. Finally
use the address of temp PDPTE as the page table address.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Combine 'if' condition branch for non-present and leaf Parent
Entry in PageTableLibMapInLevel. Most steps of these two condition
are the same. This commit doesn't change any functionality.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add code to compare ParentPagingEntry Attribute&Mask and input
Attribute&Mask to decide if new next level page table is needed
in non-present ParentPagingEntry condition. This can help avoid
unneccessary page table creation.
For example, there is a page table in which [0, 1G] is mapped(Lv4[0]
,Lv3[0,0], a non-leaf level4 entry and a leaf level3 entry).And we
only want to map [1G, 1G+2M] linear address still as non-present.
The expected behaviour should be nothing happens in the process.
However, previous code logic doesn't check if ParentPagingEntry
Attribute&Mask and input Attribute&Mask are the same in non-present
ParentPagingEntry condition. Then a new 4K memory is allocated for
Lv2 since 1G+2M is not 1G-aligned.
So when ParentPagingEntry is non-present, before allocate 4K memory
for next level paging, we also check if ParentPagingEntry Attribute&
Mask and input Attribute&Mask are the same.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Last commit changed the CpuPageTableLib API PageTableMap, unit
test code should also be modified.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The definition of IA32_MAP_ATTRIBUTE has 64 bits, and one of the bit
field PageTableBaseAddress is from bit 12 to bit 52. This means if the
compiler treats the 64bits value as two UINT32 value, the field
PageTableBaseAddress spans two UINT32 value. That's why when building in
NOOPT mode in IA32, the below issue is noticed:
unresolved external symbol __allshl
This patch fix the build failure by seperate field PageTableBaseAddress
into two fields, make sure no field spans two UINT32 value.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Modify RandomTest to check if parameter IsModified of
PageTableMap() correctlly indicates whether input page table
is modified or not.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Add OUTPUT IsModified parameter in PageTableMap() to indicate
if page table has been modified. With this parameter, caller
can know if need to call FlushTlb when the page table is in CR3.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Enable non-1:1 mapping in random test. In previous test, non-1:1
test will fail due to the non-1:1 mapping issue in CpuPageTableLib
and invalid Input Mask when creating new page table or mapping
not-present range. Now these issue have been fixed.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Modify RandomTest to check invalid input. When creating new page
table or updating exsiting page table:
1.If set [LinearAddress, LinearAddress+Length] to non-present, all
other attributes should not be provided.
2.If [LinearAddress, LinearAddress+Length] contain non-present range,
the Returnstatus of PageTableMap() should be InvalidParameter when:
2.1Some of attributes are not provided when mapping non-present range
to present.
2.2Set any other attribute without setting the non-present range to
Present.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Add LastMapEntry pointer to replace MapEntrys->Maps[MapsIndex]
in SingleMapEntryTest () of RandomTest.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Add an input parameter to control the probability of returning
true. Change RandomBoolean() in RandomTest from 50% chance
returning true to returning true with the percentage of input
Probability.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add manual test case to check input Mask and Attribute. The check
steps are:
1.Create Page table to cover [0, 2G]. All fields of MapMask should
be set.
2.Update Page table to set [2G - 8K,2G] from present to non-present.
All fields of MapMask except present should not be set.
3.Still set [2G - 8K, 2G] as not present, this case is permitted.
But set [2G - 8K, 2G] as RW is not permitted.
4.Update Page table to set [2G - 8K, 2G] as present and RW. All
fields of MapMask should be set.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
For different usage, check if the combination for Mask and
Attr is valid when creating or updating page table.
1.For non-present range
1.1Mask.Present is 0 but some other attributes is provided.
This case is invalid.
1.2Mask.Present is 1 and Attr.Present is 0. In this case,all
other attributes should not be provided.
1.3Mask.Present is 1 and Attr.Present is 1. In this case,all
attributes should be provided to intialize the attribute.
2.For present range
2.1Mask.Present is 1 and Attr.Present is 0.In this case, all
other attributes should not be provided.
All other usage for present range is permitted.
In the mentioned cases, 1.2 and 2.1 can be merged into 1 check.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
In function CreatePageTable(), add code to initialize MapMask to
MAX_UINT64. When creating new page table or map non-present range
to present, all attributes should be provided.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
When splitting leaf parent entry to smaller granularity, create
child page table before modifing parent entry. In previous code
logic, when splitting a leaf parent entry, parent entry will
point to a null 4k memory before child page table is created in
this 4k memory. When the page table to be modified is the page
table in CR3, if the executed CpuPageTableLib code is in the
range mapped by the modified leaf parent entry, then issue will
happen.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Clear PageSize bit(Bit7) for non-leaf entry in PageTableLibSetPnle.
This function is used to set non-leaf entry attributes so it should
make sure that the PageSize bit of the entry should be 0.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
In previous code logic, when splitting a leaf parent entry to
smaller granularity child page table, if the parent entry
Attribute&Mask(without PageTableBaseAddress field) is equal to the
input attribute&mask(without PageTableBaseAddress field), the split
process won't happen. This may lead to failure in non-1:1 mapping.
For example, there is a page table in which [0, 1G] is mapped(Lv4[0]
,Lv3[0,0], a non-leaf level4 entry and a leaf level3 entry). And we
want to remap [0, 2M] linear address range to [1G, 1G + 2M] with the
same attibute. The expected behaviour should be: split Lv3[0,0]
entry into 512 level2 entries and remap the first level2 entry to
cover [0, 2M]. But the split won't happen in previous code since
PageTableBaseAddress of input Attribute is not checked.
So, when checking if a leaf parent entry needs to be splitted, we
should also check if PageTableBaseAddress calculated by parent entry
is equal to the value caculated by input attribute.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Move some local variable initialization to the beginning of the
function. Also delete duplicated calculation for RegionLength.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add check for input Length in PageTableMap (). Return
RETURN_SUCCESS when input Length is 0.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Remove unneeded 'if' condition in CpuPageTableLib code.
The deleted code is in the code branch for present non-leaf parent
entry. So the 'if' check for (ParentPagingEntry->Pnle.Bits.Present
== 0) is always FALSE.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
For the case CPU logic index is 0, RSP points to the very top of all AP
stacks. That address is not mapped in page table.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Ted Kuo <ted.kuo@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Because UefiCpuPkg/UefiCpuLib is merged to MdePkg/CpuLib, remove the
dependency of UefiCpuLib.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
There are two libraries: MdePkg/CpuLib and UefiCpuPkg/UefiCpuLib. This
patch merges UefiCpuPkg/UefiCpuLib to MdePkg/CpuLib.
Change-Id: Ic26f4c2614ed6bd9840f817d50e47ac1de4bd013
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
RegisterCpuInterruptHandler did not allow setting
exception handlers for anything beyond the timer IRQ.
Beyond that, it didn't meet the spec around handling
of inputs.
RiscVSupervisorModeTrapHandler now will invoke
set handlers for both exceptions and interrupts.
Two arrays of handlers are maintained - one for exceptions
and one for interrupts.
For unhandled traps, RiscVSupervisorModeTrapHandler dumps
state using the now implemented DumpCpuContext.
For EFI_SYSTEM_CONTEXT_RISCV64, extend this with the trapped
PC address (SEPC), just like on AArch64 (ELR). This is
necessary for X86EmulatorPkg to work as it allows a trap
handler to return execution to a different place. Add
SSTATUS/STVAL as well, at least for debugging purposes. There
is no value in hiding this.
Fix nested exception handling. Handler code should not
be saving SIE (the value is saved in SSTATUS.SPIE) or
directly restored (that's done by SRET). Save and
restore the entire SSTATUS and STVAL, too.
Cc: Daniel Schaefer <git@danielschaefer.me>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Signed-off-by: Andrei Warkentin <andrei.warkentin@intel.com>
Rename AsmRelocateApLoopStart to AsmRelocateApLoopStartAmdSev
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add the 'AsmRelocateApLoopStartGeneric' for X64 processors except 64-bit
AMD processors with SEV-ES.
Remove the unused arguments of AsmRelocateApLoopStartGeneric, updated
the stack offset.
Create PageTable for the allocated reserved memory.
Only keep 4GB limitation of memory allocation for the case APs still
need to be transferred to 32-bit mode before OS.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add the union RELOCATE_AP_LOOP_ENTRY, split the path in RelocateApLoop
into two:
1. 64-bit AMD processors with SEV-ES
2. Intel processors (32-bit or 64-bit), 32-bit AMD processors, or
64-bit AMD processors without SEV-ES.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Check if AP_SAFE_STACK_SIZE is aligned with CPU_STACK_ALIGNMENT
during build time.
No functional or structural changes.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4337
This patch is to avoid configure SMBASE if SmBase relocation has been
done. If gSmmBaseHobGuid found, means SmBase info has been relocated
and recorded in the SmBase array. No need to do the relocation in
SmmCpuFeaturesInitializeProcessor().
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4076
Add the RISC-V instance of the TimerLib.
This is mostly copied from
edk2-platforms/Silicon/RISC-V/ProcessorPkg/Library/RiscVTimerLib
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Daniel Schaefer <git@danielschaefer.me>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Andrei Warkentin <andrei.warkentin@intel.com>
Acked-by: Ray Ni <ray.ni@Intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4076
Add Cpu Exception Handler library for RISC-V. This is copied
from edk2-platforms/Silicon/RISC-V/ProcessorPkg/Library/RiscVExceptionLib
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Daniel Schaefer <git@danielschaefer.me>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Andrei Warkentin <andrei.warkentin@intel.com>
Acked-by: Ray Ni <ray.ni@Intel.com>
This reverts commit 73ccde8f6d since it
results in a hang of the IA32 processor and needs further clean-up.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=4234
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Commit 0426115b67 ("UefiCpuPkg: Remove unused API in
SmmCpuFeaturesLib.h", 2022-12-21) removed the declaration of the function
SmmCpuFeaturesAllocatePageTableMemory() from the "SmmCpuFeaturesLib.h"
library class header.
Remove the API's (null-)implementation from UefiCpuPkg/SmmCpuFeaturesLib
as well.
Build-tested with:
build -a IA32 -a X64 -b NOOPT -p UefiCpuPkg/UefiCpuPkg.dsc -t GCC5
Cc: Eric Dong <eric.dong@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=4235
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Dun Tan <dun.tan@intel.com>
During the finalization of Mp initialization before booting into the OS,
depending on whether Mwait is supported or not, AsmRelocateApLoop
places Aps in MWAIT-loop or HLT-loop.
Since paging is necessary for long mode, the original implementation of
moving APs to 32-bit was to disable paging to ensure that the booting
does not crash.
The current modification creates a page table in reserved memory,
avoiding switching modes and reclaiming memory by OS. This modification
is only for 64 bit mode.
More specifically, we keep the AMD logic as the original code flow,
extract and update the Intel-related code, where the APs would stay
in 64-bit, and run in a Mwait or Hlt loop until the OS wake them up.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
AsmRelocateApLoop is replicated for future Intel Logic Extraction,
further brings AP into 64-bit, and enables paging.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4123
APIs which are defined in CcExitLib.h are added with the CcExit prefix.
This is to make the APIs' name more meaningful.
This change impacts OvmfPkg/UefiCpuPkg.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4123
VmgExitLib once was designed to provide interfaces to support #VC handler
and issue VMGEXIT instruction. After TDVF (enable TDX feature in OVMF) is
introduced, this library is updated to support #VE as well. Now the name
of VmgExitLib cannot reflect what the lib does.
This patch renames VmgExitLib to CcExitLib (Cc means Confidential
Computing). This is a simple renaming and there is no logic changes.
After renaming all the VmgExitLib related codes are updated with
CcExitLib. These changes are in OvmfPkg/UefiCpuPkg/UefiPayloadPkg.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: James Lu <james.lu@intel.com>
Reviewed-by: Gua Guo <gua.guo@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
BZ# 4093: Abstract SmmCpuFeaturesLib for sharing common code
Remove the header files those are already included in
CpuFeatureLib.h.
Signed-off-by: Abner Chang <abner.chang@amd.com>
Cc: Abdul Lateef Attar <abdattar@amd.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ# 4093: Abstract SmmCpuFeaturesLib for sharing common code
This change stripped away the code that can be
shared with other archs or vendors from Intel
implementation and put in to the common file,
leaves the Intel X86 implementation in the
IntelSmmCpuFeatureLib. Also updates the header
file and INF file.
Signed-off-by: Abner Chang <abner.chang@amd.com>
Cc: Abdul Lateef Attar <abdattar@amd.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ# 4093: Abstract SmmCpuFeaturesLib for sharing common code
Rename SmmCpuFeaturesLiCommon.c to
IntelSmmCpuFeaturesLib, because it was developed
specifically for Intel implementation. The code
that can be shared by other archs or vendors
will be stripped away and put in the common
file in the next patch.
Signed-off-by: Abner Chang <abner.chang@amd.com>
Cc: Abdul Lateef Attar <abdattar@amd.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Disable/Restore HpetTimer before and after running the Dxe
CpuExceptionHandlerLib unit test module. During the UnitTest, a
new Idt is initialized for the test. There is no handler for timer
intrrupt in this new idt. After the test module, HpetTimer does
not work any more since the comparator value register and main
counter value register for timer does not match. To fix this issue,
disable/restore HpetTimer before and after Unit Test if HpetTimer
driver has been dispatched. We don't need to send Apic Eoi in this
unit test module.When disabling timer, after RaiseTPL(), if there
is a pending timer interrupt, bit64 of Interrupt Request Register
(IRR) will be set to 1 to indicate there is a pending timer
interrupt. After RestoreTPL(), CPU will handle the pending
interrupt in IRR.Then TimerInterruptHandler calls SendApicEoi().
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
The previous change adds unit test for DxeCpuExeptionHandlerLib
in 64bit mode. This change create a PEIM to add unit test for
PeiCpuExceptionHandlerLib based on previous change.It can run
in both 32bit and 64bit modes.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Add target based unit tests for the DxeCpuExceptionHandlerLib.
A DXE driver is created to test DxeCpuExceptionHandlerLib.
Four test cases are created in this Unit Test module:
a.Test if exception handler can be registered/unregistered
for no error code exception.In the test case, only no error
code exception is triggered and tested by INTn instruction.
b.Test if exception handler can be registered/unregistered
for GP and PF. In the test case, GP exception is triggered
and tested by setting CR4_RESERVED_BIT to 1. PF exception
is triggered by writting to not-present or RO address.
c.Test if CpuContext is consistent before and after exception.
In this test case:
1.Set Cpu register to mExpectedContextInHandler before
exception. 2.Trigger exception specified by ExceptionType.
3.Store SystemContext in mActualContextInHandler and set
SystemContext to mExpectedContextAfterException in handler.
4.After return from exception, store Cpu registers in
mActualContextAfterException.
The expectation is:
1.Register values in mActualContextInHandler are the same
with register values in mExpectedContextInHandler.
2.Register values in mActualContextAfterException are the
same with register values mActualContextAfterException.
d.Test if stack overflow can be captured by CpuStackGuard
in both Bsp and AP. In this test case, stack overflow is
triggered by a funtion which calls itself continuously.
This test case triggers stack overflow in both BSP and AP.
All AP use same Idt with Bsp. The expectation is:
1. PF exception is triggered (leading to a DF if sepereated
stack is not prepared for PF) when Rsp<=StackBase+SIZE_4KB
since [StackBase, StackBase + SIZE_4KB] is marked as not
present in page table when PcdCpuStackGuard is TRUE.
2. Stack for PF/DF exception handler in both Bsp and AP is
succussfully switched by InitializeSeparateExceptionStacks.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Support PAE paging for PageTableParse API in CpuPageTableLib.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
The PEI instance of the CpuExceptionHandlerLib didn't implement the
RegisterCpuInterruptHandler() API. This patch adds the missing API.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
This commit is a code optimization to allow bigger seperate stack size in
ArchSetupExceptionStack. In previous code logic, CPU_STACK_ALIGNMENT bytes
will be wasted if StackTop is already CPU_STACK_ALIGNMENT aligned.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
To remove the dependency of CPU register, 4/8 byte at the top of the
stack is occupied for CpuMpData. BIST information is also taken care
here. This modification is only for PEI phase, since in DXE phase
CpuMpData is accessed via global variable.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
The API of InitializeSeparateExceptionStacks is just changed before, and
makes the struct CPU_EXCEPTION_INIT_DATA an internal definition.
Furthermore, we can even remove the struct to make core simpler.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
When switch bsp, old bsp and new bsp put CR0/CR4 into stack, and put IDT
and GDT register into a structure. After they exchange their stack, they
restore these registers. This logic is now implemented by assembly code.
This patch aims to reuse (Save/Restore)VolatileRegisters function to
replace such assembly code for better code readability.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3962
Two SMM variables (mSmrrSupported & mSmmFeatureControlSupported) are global
variables, they control whether the SMRR and SMM Feature Control MSR will
be restored respectively.
To avoid the TOCTOU, add PCD to control SMRR & SmmFeatureControl enable.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Currently, when waking up AP, IDT table of AP will be set in 16 bit code,
and assume the IDT table base is 32 bit. However, the IDT table is created
by BSP. Issue will happen if the BSP allocates memory above 4G for BSP's
IDT table. Moreover, even the IDT table location is below 4G, the handler
function inside the IDT table is 64 bit, and it won't take effect until
CPU transfers to 64 bit long mode. There is no benefit to set IDT table in
such an early phase.
To avoid such issue, this patch moves the LIDT instruction into 64 bit
code.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Add host based unit tests for the CpuPageTableLib services.
Unit test focuses on PageTableMap function, containing two kinds of test
cases: manual test case and random test case.
Manual test case creates some corner case to test function PageTableMap.
Random test case generates multiple random memory entries (with random
attribute) as the input of function PageTableMap to get the output
pagetable. Output pagetable will be validated and be parsed to get output
memory entries, and then the input and output memory entries will be
compared to verify the functionality.
The unit test is not perfect yet. There are options for random test, and
some of them control the test coverage, and some option are not ready.
Will enhance in the future.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
This reverts commit 2812668bfc for tag202208.
This feature will be merged after stable tag 202208 is created.
Signed-off-by: Liming Gao <gaoliming@byosoft.com.cn>
Reviewed-by: Zhiguang Liu <zhiguang.liu@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Add host based unit tests for the CpuPageTableLib services.
Unit test focuses on PageTableMap function, containing two kinds of test
cases: manual test case and random test case.
Manual test case creates some corner case to test function PageTableMap.
Random test case generates multiple random memory entries (with random
attribute) as the input of function PageTableMap to get the output
pagetable. Output pagetable will be validated and be parsed to get output
memory entries, and then the input and output memory entries will be
compared to verify the functionality.
The unit test is not perfect yet. There are options for random test, and
some of them control the test coverage, and some option are not ready.
Will enhance in the future.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The change doesn't change functionality behavior.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
With following paging structure to map
[2M-4K, 2M] as P = 1, RW = 0,
[2M, 4M] as P = 1, RW = 1:
PML4[0] -> PDPTE[0] -> PDE[0](RW = 0) -> PTE[255](P = 0, RW = 0)
-> PDE[1](RW = 1)
When a new request to map [2M-4K, 2M+4K] as P = 1, RW = 1,
CpuPageTableMap() wrongly requests 4K buffer size for the new mapping
request.
But in fact, for [2M-4K, 2M] request, PTE[255] can be changed in place,
for [2M, 2M+4K], no change is needed because PDE[1].RW = 1 already.
The change fixes the bug.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
With the following paging structure that maps [0, 2G] with ReadWrite
bit set.
PML4[0] --> PDPTE[0] --> PDE[0-255]
\-> PDPTE[1] --> PDE[0-255]
If ReadWrite bit is cleared in PML4[0] and PageTableMap() is called
to change [0, 2M] as read-only, today's logic unnecessarily changes
the paging structure in 2 aspects:
1. When setting PageTableBaseAddress in the entry, the code clears
all attributes.
2. Even the ReadWrite bit in parent entry is not set, the code clears
the ReadWrite bit in the leaf entry.
First change is wrong. It should not change other attributes when
setting the PA.
Second change is unnecessary. Because the parent entry already
declares the whole region as read-only, there is no need to clear
ReadWrite bit in the leaf entry again.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
With the following paging structure that maps [0, 2G] with ReadWrite
bit set.
PML4[0] --> PDPTE[0] --> PDE[0-255]
\-> PDPTE[1] --> PDE[0-255]
If ReadWrite bit is cleared in PML4[0] and PageTableMap() is called
to change [0, 2M] as writable, today's logic doesn't inherit the
parent entry's attributes when determining the child entry's
attributes. It just sets the PDPTE[0].PDE[0].ReadWrite bit.
But since the PML4[0].ReadWrite is 0, [0, 2M] is still read-only.
The change fixes the bug.
If the inheritable attributes in ParentPagingEntry conflicts with the
requested attributes, let the child entries take the parent attributes
and loosen the attribute in the parent entry.
E.g.: when PDPTE[0].ReadWrite = 0 but caller wants to map [0-2MB as
ReadWrite = 1 (PDE[0].ReadWrite = 1), we need to change
PDPTE[0].ReadWrite = 1 and let all PDE[0-255].ReadWrite = 0 first.
Then change PDE[0].ReadWrite = 1.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's logic wrongly treats the non-leaf entry as leaf entry and
updates its paging attributes.
The patch fixes the bug to only update paging attributes for
non-present entries or leaf entries.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When PageTableMap() is called to create non 1:1 mapping
such as [0, 1G) to [8K, 1G+8K), it should split the page entry to the
4K page level, but old logic has a bug that it just uses 1G page
entry.
The patch fixes the bug.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch replaces
LinearAddress + Offset == RegionStart
with
((LinearAddress + Offset) & RegionMask) == 0
The replace should not cause any behavior change.
Because:
1. In first loop of while when LinearAddress + Offset == RegionStart,
because the lower "BitStart" bits of RegionStart are all-zero,
all lower "BitStart" bits of (LinearAddress + Offset) are all-zero.
Because all lower "BitStart" bits of RegionMask is all-one and
bits are all-zero, ((LinearAddress + Offset) & RegionMask) == 0.
2. In following loops of the while, even RegionStart is increased
by RegionLength, the lower "BitStart" bits are still all-zero.
So the two expressions still semantically equal to each other.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When LinearAddress or Length is not aligned on 4KB, PageTableMap()
should return Invalid Parameter.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The lib includes two APIs:
* PageTableMap
It creates/updates mapping from LA to PA.
The implementation only supports paging structures used in 64bit
mode now. PAE paging structure support will be added in future.
* PageTableParse
It parses the page table and returns the mapping relations in an
array of IA32_MAP_ENTRY.
It passed some stress tests. These test code will be upstreamed in
other patches following edk2 Unit Test framework.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
CPU_EXCEPTION_INIT_DATA is now an internal implementation of
CpuExceptionHandlerLib. Union can be removed since Ia32 and X64 have the
same definition. Also, two fields (Revision and InitDefaultHandlers)are
useless, can be removed.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Since the API InitializeSeparateExceptionStacks is simplified and does't
use the struct CPU_EXCEPTION_INIT_DATA, CPU_EXCEPTION_INIT_DATA become
a inner implementation of CpuExcetionHandlerLib.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Jian J Wang <jian.j.wang@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Hide the Exception implementation details in CpuExcetionHandlerLib and
caller only need to provide buffer
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Currently, "push byte %[Vector]" causes nasm warning when Vector is larger
than 0x7F. This is because push accepts a signed value, and byte means
signed int8. Maximum signed int8 is 0x7F.
When Vector is larger the 0x7F, for example, when Vector is 255, byte 255
turns to -1, and causes the warning "signed byte value exceeds".
To avoid such warning, use dword instead of byte, this will increase 3 bytes
for each IdtVector.
For IA32, the size of IdtVector will increase from 10 bytes to 13 bytes.
For X64, the size of IdtVector will increase from 15 bytes to 18 bytes.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Debkumar De <debkumar.de@intel.com>
Cc: Harry Han <harry.han@intel.com>
Cc: Catharine West <catharine.west@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Xie, Yuanhao
Abdul Lateef Attar
Abdul Lateef Attar
Tuan Phan
Dun Tan
Yu Pu
Rebecca Cran
Ard Biesheuvel
Gerd Hoffmann
Lendacky, Thomas via groups.io
Ray Ni
Zhiguang Liu
Andrei Warkentin
Wu, Jiaxin
Sunil V L
Laszlo Ersek
Min M Xu
Abner Chang
Liming Gao