The commit is a follow-up of commit 8491e30.
In file MpService.c line 786:
Pte[Index] = (UINT64)((UINTN)PageTable + EFI_PAGE_SIZE * (Index + 1)) |
mAddressEncMask ...
(Where PageTable is of type VOID*, Index is of type UINTN, mAddressEncMask
is of type UINT64 and Pte[Index] is of type UINT64.)
Since in this case, the code logic ensures that the expression will not
exceed the range of UINTN, the commit will remove the explicit type cast
'(UINT64)'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
The mask is applied when page tables entries are created or modified.
CC: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
There are cases that the operands of an expression are all with rank less
than UINT64/INT64 and the result of the expression is explicitly cast to
UINT64/INT64 to fit the target size.
An example will be:
UINT32 a,b;
// a and b can be any unsigned int type with rank less than UINT64, like
// UINT8, UINT16, etc.
UINT64 c;
c = (UINT64) (a + b);
Some static code checkers may warn that the expression result might
overflow within the rank of "int" (integer promotions) and the result is
then cast to a bigger size.
The commit refines codes by the following rules:
1). When the expression is possible to overflow the range of unsigned int/
int:
c = (UINT64)a + b;
2). When the expression will not overflow within the rank of "int", remove
the explicit type casts:
c = a + b;
3). When the expression will be cast to pointer of possible greater size:
UINT32 a,b;
VOID *c;
c = (VOID *)(UINTN)(a + b); --> c = (VOID *)((UINTN)a + b);
4). When one side of a comparison expression contains only operands with
rank less than UINT32:
UINT8 a;
UINT16 b;
UINTN c;
if ((UINTN)(a + b) > c) {...} --> if (((UINT32)a + b) > c) {...}
For rule 4), if we remove the 'UINTN' type cast like:
if (a + b > c) {...}
The VS compiler will complain with warning C4018 (signed/unsigned
mismatch, level 3 warning) due to promoting 'a + b' to type 'int'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
The mask is applied when page tables entriees are created or modified.
CC: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
The mask is applied when page tables are created (S3Resume.c).
CC: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Platform PEI may add LOCAL APIC memory mapped space into
EFI_HOB_MEMORY_ALLOCATION. Or platform may allocate this range before.
So, we skip AllocateMemorySpace()'s return status checking. Instead, we add one
DEBUG message for possible trace.
https://bugzilla.tianocore.org/show_bug.cgi?id=390
This updating is suggested by Ersek's comments at
https://www.mail-archive.com/edk2-devel@lists.01.org/msg22585.html
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Current CpuGetTimerValue() implementation return hard code TimerPeriod value. We
could calculate the actual TimerPeriod value over period of time (100us) at the
first time invoking CpuGetTimerValue() and save the TimerPeriod value into one
global variable to avoid delay at the next CpuGetTimerValue() invoking.
https://bugzilla.tianocore.org/show_bug.cgi?id=382
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Local APIC memory mapped space should be added into GCD and be allocated.
Otherwise, UEFI firmware cannot get correct memory map for it. For example,
SMM profile feature needs to get the completed MMIO map to protect them.
v2:
Consume AddMemoryMappedIoSpace() to handle the case that Local APIC
memory space has already been added before.
https://bugzilla.tianocore.org/show_bug.cgi?id=390
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Add memory attribute setting in CpuArch protocol.
Previous SetMemoryAttributes() API only supports cache attribute setting.
This patch updated SetMemoryAttributes() API to support memory attribute
setting by updating CPU page table.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
X64\ExceptionHandlerAsm.S define MARCO to set up 32 IDT entries header.
It assume GCC compiler will generate the same code length on the following
instrction for each IDT entry.
jmp ASM_PFX(CommonInterruptEntry)
It works with GCC 4.x. However, GCC 5.4 will generate different code size of IDT
entry code per the offset value from CommonInterruptEntry address. We should use
DB to make sure each IDT entry header has the same size whatever compiler
version.
.ASM and .nasm used the different solution and do not have this issue.
https://bugzilla.tianocore.org/show_bug.cgi?id=389
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The IO_PPI supports Fifo types by invoking the Fifo routines in the
new BaseIoLibIntrinsic (IoLib class) library.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The Fifo routines from the UefiCpuPkg/CpuIo2Dxe driver have been
moved to the new BaseIoLibIntrinsic (IoLib class) library.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
This fix is to pass VS2010/VS2012 build.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
We need to set new AP to idle state if it is expected to be waken up by new BSP
later.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
We need to disable system timer interrup to avoid generating the pending
interrupt on the old BSP.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
We need to swap local APIC timer interrupt state between old BSP and new BSP.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
During switching BSP phase, we need to disable CPU interruput to prevent stack
crashed by Timer interrupt handle. But when we enabled source debugging feature,
debug timer interrupt handler (existing on both PEI and DXE) also could crash
the stack used during switching BSP. So,we need to move save/restore interrupt
to SwitchBSPWorker().
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If APs are waken up by INIT-SIPI-SIPI command, they will lose original local
APIC timer setting. As a result, the timer library instance based on local APIC
timer cannot work on APs function.
This fix is to save BSP's local APIC timer settings before waking up APs and
to sync to APs when APs wakeup by INIT-SIPI-SIPI command.
Setting BSP's current counter to AP's initial counter could make sure BSP and
APs have same counter value across BSP switching.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The current DxeDebugAgentLib supports source debugging on AP function. This
update is to update DxeMpInitLib to consume Debug Agent Library by
DEBUG_AGENT_INIT_DXE_AP flag. Thus, we could source debugging AP function
invoked by CPU MP Protocol.
However, current SecPeiDebugAgentLib does not support source debugging on AP
function invoked by CPU MP PPI. I have submitted one bugzilla to add this
support at https://bugzilla.tianocore.org/show_bug.cgi?id=308.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Support the case that BSP and AP are using different Microcode.
The previous logic validates new MCU on BSP only.
The enhanced logic will validate MCU on every BSP and AP.
As long as one processor loads the MCU successfully, it will be updated.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The patch updated MicrocodeWrite() to move the Microcode replacement logic
to a standalone function - UpdateMicrocodeFlashRegion().
More detail description is added in UpdateMicrocodeFlashRegion()
to improve readability.
The Microcode information is collected in InitializeMicrocodeDescriptor(),
so that FmpGetImage() can get the info directly.
MicrocodeRead() is not needed any more.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Add PcdCpuSmmStmExceptionStackSize/PcdCpuMsegSize prompt and help
string to uni file.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
This patch sets the normal OS buffer EfiLoaderCode/Data,
EfiBootServicesCode/Data, EfiConventionalMemory, EfiACPIReclaimMemory
to be not present after SmmReadyToLock.
To access these region in OS runtime phase is not a good solution.
Previously, we did similar check in SmmMemLib to help SMI handler
do the check. But if SMI handler forgets the check, it can still
access these OS region and bring risk.
So here we enforce the policy to prevent it happening.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Add a new instances of the SmmCpuFeaturesLib that is used by
platforms to enable the SMI Transfer Monitor(STM) feature.
This new instance is in the same directory as the default
SmmCpuFeaturesLib instance in order to share source files.
The DSC file is updated to build both SmmCpuFeatureLib
instances and to build two versions of the PiSmmCpuDxeSmm
module using each of the SmmCpuFeatureLib instances.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Split the default implementation of the SmmCpuFeaturesLib
into two files to prepare for the addition of the STM
specific SmmCpuFeaturesLib implementation. The STM
specific implementation installs a different SMI entry
handler and initialize the MSEG specific MSR at the end
of SmmCpuFeaturesInitializeProcessor().
This patch does not introduce any functional changes
to the default implementation of the SmmCpuFeaturesLib.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
* Add GUIDed HOB that described MSEG region in SMRAM
* Add SM Monitor Init Protocol
* Add PCD to configure size of SMM exception stack
* Add PCD to configure MSEG region size if it is not
described by the gMsegSmramGuid GUIDed HOB.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Add comments to describe fields of MSEG_HEADER and
add define values for the MonitorFeatures field.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=176
Update CPUID leaf and sub-leaf indexes and structures as described by
Intel(R) 64 and IA-32 Architectures Software Developer's Manual,
Volume 2A, September 2016, CPUID instruction.
Summary of incompatible changes:
1. Field name changes in CPUID_STRUCTURED_EXTENDED_FEATURE_FLAGS_EBX
Bit 12 has been renamed from 'PQM' to 'RDT_M' and bit 15 has been renamed
from 'PQE' to 'RDT_A'.
2. Stucture and filed name changes for 'CPUID Platform QoS Monitoring
Information' related definitions
Definition 'CPUID_PLATFORM_QOS_MONITORING' has been renamed to
'CPUID_INTEL_RDT_MONITORING'.
Definition 'CPUID_PLATFORM_QOS_MONITORING_ENUMERATION_SUB_LEAF' has been
renamed to 'CPUID_INTEL_RDT_MONITORING_ENUMERATION_SUB_LEAF'.
Definition 'CPUID_PLATFORM_QOS_MONITORING_CAPABILITY_SUB_LEAF' has been
renamed to 'CPUID_INTEL_RDT_MONITORING_L3_CACHE_SUB_LEAF'.
3. Stucture and filed name changes for 'CPUID Platform QoS Enforcement
Information' related definitions
Definition 'CPUID_PLATFORM_QOS_ENFORCEMENT' has been renamed to
'CPUID_INTEL_RDT_ALLOCATION'.
Definition 'CPUID_PLATFORM_QOS_ENFORCEMENT_MAIN_LEAF' has been renamed to
'CPUID_INTEL_RDT_ALLOCATION_ENUMERATION_SUB_LEAF'.
Definition 'CPUID_PLATFORM_QOS_ENFORCEMENT_RESID_SUB_LEAF' has been
renamed to 'CPUID_INTEL_RDT_ALLOCATION_L3_CACHE_SUB_LEAF'.
This commit also updates the relating codes in
UefiCpuPkg/Application/Cpuid to reflect the changes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=176
Update the MSR header file of Skylake processor according to Intel(R) 64
and IA-32 Architectures Software Developer's Manual, Volume 3, September
2016, Chapter 35 Model-Specific-Registers (MSR), Section 35.15.
Summary of incompatible changes:
1. MSR (address 38EH) IA32_PERF_GLOBAL_STAUS has been renamed to
IA32_PERF_GLOBAL_STATUS
Typo 'STAUS' has been fixed in SDM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=176
Update MSR header files of processors (excluding Goldmont and Skylake
processors) according to Intel(R) 64 and IA-32 Architectures Software
Developer's Manual, Volume 3, September 2016, Chapter 35
Model-Specific-Registers (MSR).
Summary of incompatible changes:
General:
1. MSR (address 38EH) IA32_PERF_GLOBAL_STAUS in processor-specific header
files has been removed or renamed to IA32_PERF_GLOBAL_STATUS
Typo 'STAUS' has been fixed in SDM.
If the MSR definition is the same with architectural MSR, we remove it.
Otherwise, we rename the MSR.
2. MSRs (address starting from 400H) MSR_MC{X}_{XXX} (like MSR_MC4_STATUS)
in processor-specific header files have been removed or renamed to
IA32_MC{X}_{XXX} (like IA32_MC4_STATUS)
Register name change from 'MSR_MC{X}_{XXX}' to 'IA32_MC{X}_{XXX}' in SDM.
If the MSR definition is the same with architectural MSR, we remove it.
Otherwise, we rename the MSR.
Please note that for those MSRs still have name like 'MSR_MC{X}_{XXX}' in
SDM are still kept in processor-specific header files.
HaswellMsr.h:
1. MSR (address C80H) IA32_DEBUG_FEATURE has been removed
Register name change from 'IA32_DEBUG_FEATURE' to 'IA32_DEBUG_INTERFACE'
in SDM.
Since the MSR definition is the same with architectural MSR, we remove it.
SandyBridgeMsr.h:
1. MSR (address 391H) MSR_UNC_PERF_GLOBAL_CTRL, name change for bit fields
0:3
Bit description change from 'Core {X} select' to 'Slice {X} select' for
bit 0:3 in SDM.
SilvermontMsr.h:
1. MSR (address 2AH) MSR_EBL_CR_POWERON, structure definition changed
Bit description for this MSR is totally changed in SDM, we modify the
structure definition to align with it.
XeonDMsr.h:
1. MSRs (address 630H to 632H) MSR_PKG_C8_RESIDENCY, MSR_PKG_C9_RESIDENCY
and MSR_PKG_C10_RESIDENCY have been removed
Those 3 MSRs are not defined for this processor in SDM, we remove them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
1. Add MicrocodeUpdate.h to the [Sources] section.
2. Fix the incorrect Guid/Protocol format issues.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=277
The MTRR field was removed from PROCESS_SMM_DESCRIPTOR
structure in commit:
26ab5ac362
However, the references to the MTRR field in assembly
files were not removed. Remove the extern reference
to gSmiMtrr and set the Reserved14 field
of PROCESS_SMM_DESCRIPTOR to 0.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The following commit moved the initialization of the
default PROCESSOR_SMM_DESCRIPTOR from MpService.c to
SmramSaveState.c and made this initialization
conditional on the value returned by the
SmmCpuFeaturesGetSmiHandlerSize() library function.
f12367a0b1
This changed the behavior of the PiSmmCpuDxeSmm module.
The initialization of the PROCESSOR_SMM_DESCRIPTOR is
moved before the call to SmmCpuFeaturesGetSmiHandlerSize()
to preserve the previous behavior.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch fixes https://bugzilla.tianocore.org/show_bug.cgi?id=246
Previously, when SMM exception happens after EndOfDxe,
with StackGuard enabled on IA32, the #double fault exception
is reported instead of #page fault.
Root cause is below:
Current EDKII SMM page protection will lock GDT.
If IA32 stack guard is enabled, the page fault handler will do task switch.
This task switch need write busy flag in GDT, and write TSS.
However, the GDT and TSS is locked at that time, so the
double fault happens.
We decide to not lock GDT for IA32 StackGuard enabled.
This issue does not exist on X64, or IA32 without StackGuard.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=279
Add MSR_IA32_VMX_BASIC_REGISTER and IA32_VMX_MISC_REGISTER
structures with the bit fields for these two MSRs. Also
add MSEG_HEADER structure whose base address is in the
MsegBase field of MSR_IA32_SMM_MONITOR_CTL_REGISTER.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=277
Remove dependency on layout of PROCESSOR_SMM_DESCRIPTOR
everywhere possible. The only exception is the standard
SMI entry handler template that is included with the
PiSmmCpuDxeSmm module. This allows an instance of the
SmmCpuFeaturesLib to provide alternate
PROCESSOR_SMM_DESCRIPTOR structure layouts.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=277
All CPUs use the same MTRR settings. Move MTRR settings
from a field in the PROCESSOR_SMM_DESCRIPTOR structure into
a module global variable.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
mReservedVectors is not set, we could add parameter ExceptionHandlerData for
ArchRestoreExceptionContext() that could use it instead of mReservedVectors.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
mReservedVectors is not set, we could add parameter ExceptionHandlerData for
ArchSaveExceptionContext() that could use it instead of mReservedVectors.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Some semaphores are not cleared on S3 boot path. For example,
mSmmMpSyncData->CpuData[CpuIndex].Present. It may still keeps the value set at
SMM runtime during S3 resume. It may causes BSP have the wrong judgement on SMM
AP's present state.
We have one related fix at e78a2a49ee. But that is
not completed.
This fix is to clear Busy/Run/Present semaphores in InitializeMpSyncData().
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Current GetImage API forgets to return data to caller.
Add code to fix it.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
PiSmmCpu driver may split page for page attribute request.
Current logic not only propagates the super page attribute to
the leaf page attribut, but also to the directory page attribute.
However, the later might be wrong because we cannot clear protection
without touching directory page attribute.
The effective protection is the strictest combination
across the levels.
We should always clear protection on directory page and set
protection on leaf page for easy clearing later.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Sometimes a platform knows exactly how many CPUs it has at boot. It should
be able to
- set PcdCpuMaxLogicalProcessorNumber dynamically to this number,
- set PcdCpuApInitTimeOutInMicroSeconds to a very long time (for example
MAX_UINT32, approx. 71 minutes),
- and expect that MpInitLib wait exactly as long as necessary for all APs
to report in.
Other platforms should be able to continue setting a reasonably large
upper bound on supported CPUs, and waiting for a reasonable, fixed amount
of time for all APs to report in.
Add this functionality. The TimedWaitForApFinish() function will return
when all APs have reported in, or the timeout has expired -- whichever
happens first.
(Accessing these PCDs dynamically is safe. The PEI and DXE phase instances
of this library are restricted to PEIM and DXE_DRIVER client modules, thus
the PCD accesses cannot be linked into runtime code.)
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=116
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
"UefiCpuPkg/UefiCpuPkg.dec" already allows platforms to make
PcdCpuMaxLogicalProcessorNumber dynamic, however PiSmmCpuDxeSmm does not
take this into account everywhere. As soon as a platform turns the PCD
into a dynamic one, at least S3 fails. When the PCD is dynamic, all
PcdGet() calls translate into PCD DXE protocol calls, which are only
permitted at boot time, not at runtime or during S3 resume.
We already have a variable called mMaxNumberOfCpus; it is initialized in
the entry point function like this:
> //
> // If support CPU hot plug, we need to allocate resources for possibly
> // hot-added processors
> //
> if (FeaturePcdGet (PcdCpuHotPlugSupport)) {
> mMaxNumberOfCpus = PcdGet32 (PcdCpuMaxLogicalProcessorNumber);
> } else {
> mMaxNumberOfCpus = mNumberOfCpus;
> }
There's another use of the PCD a bit higher up, also in the entry point
function:
> //
> // Use MP Services Protocol to retrieve the number of processors and
> // number of enabled processors
> //
> Status = MpServices->GetNumberOfProcessors (MpServices, &mNumberOfCpus,
> &NumberOfEnabledProcessors);
> ASSERT_EFI_ERROR (Status);
> ASSERT (mNumberOfCpus <= PcdGet32 (PcdCpuMaxLogicalProcessorNumber));
Preserve these calls in the entry point function, and replace all other
uses of PcdCpuMaxLogicalProcessorNumber -- there are only reads -- with
mMaxNumberOfCpus.
For PcdCpuHotPlugSupport==TRUE, this is an unobservable change.
For PcdCpuHotPlugSupport==FALSE, we even save SMRAM, because we no longer
allocate resources needlessly for CPUs that can never appear in the
system.
PcdCpuMaxLogicalProcessorNumber is also retrieved in
"UefiCpuPkg/Library/SmmCpuFeaturesLib/SmmCpuFeaturesLib.c", but only in
the library instance constructor, which runs even before the entry point
function is called.
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=116
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
AP will get target C-State from eax[7:4]. We do shift in ebx firstly before set
to eax. It will lead ebx is incorrect in the next time.
The fix is to set ebx to eax firstly and does shift in eax. Thus, ebx could keep
original value.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Add one semaphore to make sure BSP to wait till all APs run in AP safe loop
code.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
For long mode DXE, we will disable paging on AP to protected mode to execute AP
safe loop code in reserved memory range under 4GB. But we forget to allocate
stack for AP under 4GB and AP still are using original AP stack. If original AP
stack is larger than 4GB, it cannot be used after AP is transferred to protected
mode. Besides MwaitSupport == TRUE, AP stack is still required during phase of
disabling paging in long mode DXE.
Moreover, even though AP stack is always under 4GB (a) in Ia32 DXE and (b) with
this patch, after transferring to protected mode from X64 DXE, AP stack
(in BootServiceData) maybe crashed by OS after Exit Boot Service event.
This fix is to allocate reserved memory range under 4GB together with AP safe
loop code. APs will switch to new stack in safe loop code.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
AP loop function is already saved into global variable, needn't to get it from
AP function parameter.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
This patch fixes the first part of
https://bugzilla.tianocore.org/show_bug.cgi?id=242
Previously, when SMM exception happens, "stack overflow" is misreported.
This patch checked the PF address to see it is stack overflow, or
it is caused by SMM page protection.
It dumps exception data, PF address and the module trigger the issue.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
According to the Intel SDM (325462-060US / September 2016),
> INPUT EAX = 0BH: Returns Extended Topology Information
>
> [...] Software must detect the presence of CPUID leaf 0BH by verifying
> (a) the highest leaf index supported by CPUID is >= 0BH, and
> (b) CPUID.0BH:EBX[15:0] reports a non-zero value. [...]
The "GetApicId" sections in the Ia32 and X64 "MpFuncs.nasm" files do not
perform check (b).
This causes an actual bug in the following OVMF setup:
- Intel W3550 host processor <http://ark.intel.com/products/39720/>,
- the QEMU/KVM guest's VCPU model is set to "host", that is, "the CPU
visible to the guest should be exactly the same as the host CPU".
Under "GetApicId", check (a) passes: the CPUID level of the W3550 is
exactly 11 decimal. However, leaf 11 itself is not supported, therefore
EDX is set to zero:
> If a value entered for CPUID.EAX is less than or equal to the maximum
> input value and the leaf is not supported on that processor then 0 is
> returned in all the registers.
Because we don't check (b), the "GetProcessorNumber" section of the code
is reached with an initial APIC ID of 0 in EDX on all of the APs. Given
that "GetProcessorNumber" searches the
"MP_CPU_EXCHANGE_INFO.CpuInfo[*].InitialApicId" fields for a match, all
APs enter ApWakeupFunction() with an identical "NumApsExecuting"
parameter. This results in unpredictable guest behavior (crashes, reboots,
hangs etc).
Reorganize the "GetApicId" section and add the missing check in both
assembly files.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
According to the Intel SDM (325462-060US / September 2016),
> INPUT EAX = 0BH: Returns Extended Topology Information
>
> [...] Software must detect the presence of CPUID leaf 0BH by verifying
> (a) the highest leaf index supported by CPUID is >= 0BH, and
> (b) CPUID.0BH:EBX[15:0] reports a non-zero value. [...]
The LocalApicLib instances in UefiCpuPkg do not perform check (b).
This causes an actual bug in the following OVMF setup:
- Intel W3550 host processor <http://ark.intel.com/products/39720/>,
- the QEMU/KVM guest's VCPU model is set to "host", that is, "the CPU
visible to the guest should be exactly the same as the host CPU".
In the GetInitialApicId() function, check (a) passes: the CPUID level of
the W3550 is exactly 11 decimal. However, leaf 11 itself is not supported,
therefore EDX is set to zero:
> If a value entered for CPUID.EAX is less than or equal to the maximum
> input value and the leaf is not supported on that processor then 0 is
> returned in all the registers.
Because we don't check (b), we return 0 as initial APIC ID on the BSP and
on all of the APs as well.
Add the missing check.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Move the declaration of these PCDs from the
[PcdsFixedAtBuild, PcdsPatchableInModule]
section of "UefiCpuPkg/UefiCpuPkg.dec" to the
[PcdsFixedAtBuild, PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx]
section. Their types, default values, and token values remain unchanged.
Only UefiCpuPkg/PiSmmCpuDxeSmm consumes these PCDs, specifically on the
call stack of its entry point function, and it turns them into static or
dynamically allocated data in SMRAM:
PiCpuSmmEntry() [PiSmmCpuDxeSmm.c]
InitializeSmmTimer() [SyncTimer.c]
PcdCpuSmmApSyncTimeout
-> mTimeoutTicker
InitializeMpServiceData() [MpService.c]
InitializeMpSyncData() [MpService.c]
PcdCpuSmmSyncMode
-> mSmmMpSyncData->EffectiveSyncMode
However, there's another call path to fetching "PcdCpuSmmSyncMode", namely
SmmInitHandler() [PiSmmCpuDxeSmm.c]
InitializeMpSyncData() [MpService.c]
PcdCpuSmmSyncMode
-> mSmmMpSyncData->EffectiveSyncMode
and this path is exercised during S3 resume (as stated by the comment in
SmmInitHandler() too, "Initialize private data during S3 resume").
While we can call the PCD protocol (via PcdLib) for fetching dynamic PCDs
in the entry point function, we cannot do that at S3 resume. Therefore
pre-fetch PcdCpuSmmSyncMode into a new global variable (which lives in
SMRAM) in InitializeMpServiceData(), just before calling
InitializeMpSyncData(). This way InitializeMpSyncData() can retrieve the
stashed PCD value from SMRAM, regardless of the boot mode.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=230
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
When XD is not supported, the BIT63 is reserved.
We should not set BIT63 in the page table.
Test OVMF IA32/IA32X64 with XD enabled/disabled.
Analyzed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
v2:
Per Laszlo and Andrew's comments at
https://lists.01.org/pipermail/edk2-devel/2016-November/004759.html
SecCoreData->StackBase is VOID * type. We should use %p to dump VOID * type.
SecCoreData->StackSize is UINTN type, but %x only could print unsinged-int
type. We will cast it to UINT32 firstly and then use %x to print it.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Once platform selects the incorrect instance, the caller could know it from
return status and ASSERT().
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Add volatile qualifier to mNumberToFinish to prevent GCC 5.4
compiler from optimizing away required logic in ACPI S3 resume.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Update TransferApToSafeState() use UINTN params to reduce the
number of type casts required in these calls. Also change
the NumberToFinish parameter from UINT32* to UINTN
NumberToFinishAddress to resolve issues with conversion from
a volatile pointer to a non-volatile pointer. The assembly
code that receives the NumberToFinishAddress value must treat
that memory location as a volatile to track the number of APs.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The cached "CPU_INFO_IN_HOB.ApTopOfStack" field currently has type UINT32.
This is not ideal because the AP stacks are located within
"CpuMpData->Buffer", which is allocated with a plain AllocatePages() call
in MpInitLibInitialize():
platform CpuMpPei included PEI RAM > 4GB result
-------- ----------------- ------------- ------
Ia32 * n/a good
Ia32X64 no n/a BAD
Ia32X64 yes n/a good
X64 no * BAD
X64 yes no good
X64 yes yes BAD
- If we are on an Ia32X64 or X64 platform that does not include CpuMpPei,
then CpuDxe cannot reuse the CPU_INFO_IN_HOB structures preallocated by
CpuMpPei (through the CpuInitMpLib GUID HOB), and then AllocatePages()
-- invoked first in 64-bit DXE -- could return an address outside of
32-bit address space.
- If we are on an X64 platform where the permanent PEI RAM extends above
the 32-bit address space, then the same issue can surface even if
CpuMpPei is included: even the original allocation of the
CPU_INFO_IN_HOB structures, by CpuMpPei, could be satisfied from above
4GB.
The original "AP init" branch in "X64/MpFuncs.nasm" correctly considers a
64-bit stack start: the "MP_CPU_EXCHANGE_INFO.StackStart" field has type
UINTN, and the code uses QWORD addition and movement to set RSP from it.
Adapt the "GetApicId" branch of "X64/MpFuncs.nasm":
- change the type of "CPU_INFO_IN_HOB.ApTopOfStack" to UINT64,
- remove the explicit truncation to UINT32 in InitializeApData(),
- update the "GetNextProcNumber" iteration size to the new size of
"CPU_INFO_IN_HOB",
- set RSP with a QWORD movement from "CPU_INFO_IN_HOB.ApTopOfStack".
Because the same CPU_INFO_IN_HOB structure is used by "Ia32/MpFuncs.nasm",
we have to update the "GetNextProcNumber" iteration size there as well.
The ESP setting can be preserved as a DWORD movement from the original
offset (decimal 12), since our integers are little endian.
Cc: Jeff Fan <jeff.fan@intel.com>
Fixes: 845c5be1fd
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The recent patch "UefiCpuPkg/MpInitLib: Program AP stack in fixed address"
inadvertently broke the first startup of APs during X64 PEI, because in
the TestLock section of the code, it replaced the access to the
NumApsExecuting counter with an access to the unrelated InitFlag field.
Cc: Jeff Fan <jeff.fan@intel.com>
Fixes: 845c5be1fd
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
At this point, ESI still has the value from EBX.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
PiSmmCpuDxeSmm consumes SmmAttributesTable and setup page table:
1) Code region is marked as read-only and Data region is non-executable,
if the PE image is 4K aligned.
2) Important data structure is set to RO, such as GDT/IDT.
3) SmmSaveState is set to non-executable,
and SmmEntrypoint is set to read-only.
4) If static page is supported, page table is read-only.
We use page table to protect other components, and itself.
If we use dynamic paging, we can still provide *partial* protection.
And hope page table is not modified by other components.
The XD enabling code is moved to SmiEntry to let NX take effect.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
If enabled, SMM will not use on-demand paging.
SMM will build static page table for all memory.
The page table size depend on 2 things:
1) The 1G paging capability.
2) The whole system memory/MMIO addressing capability.
A) If the system only supports 2M paging,
When the whole memory/MMIO is 32bit, we only need 1+1+4=6 pages for 4G.
When the whole memory/MMIO is 39bit, we need 1+1+256 pages (~ 1M)
When the whole memory/MMIO is 48bit, we need 1+256+256*256 pages (~ 257M)
B) If the system supports 1G paging.
When the whole memory/MMIO is 32bit, we only need 1+1+4=6 pages for 4G.
(We still generate 2M page for maintenance consideration.)
When the whole memory/MMIO is 39bit, we still need 6 pages.
(We setup 1G paging for >1G.)
When the whole memory/MMIO is 48bit, we need 1+256 pages (~ 1M).
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
When BSP switched, we need to update some AP information. For example,
ApStartupSignalBuffer and ApTopOfStack.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Currently, MpInitLib will program AP stack in dynamic address. Each processor
will calculate its stack address by adding stack size based on the last stack
address. That means AP may have the different stack address everytime it is
wakeup by INIT-SIPI-SIPI.
When all APs have wakeup to execute AP task, each each has been assigned one
stack address. Once the timeout happened on some of APs, BSP will send INIT-
SIPI-SIPI to wake up APs. We need to re-assign stack for APs. Based on the
current implementation, we might assign one stack address used by other APs.
It will cause the unexpected stack overlapped issue.
This fix changed the stack assignment policy. We will record the stack address
assigned to AP at first time AP wakeup. When AP failed on AP task, BSP could
reassigned the same stack for it.
Getting initial APIC ID in assembly code could help AP to get saved its stack
address.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Some CPU information (InitialApicId/ApicId/Health) are duplicated in CPU_AP_DATA
and CPU_INFO_IN_HOB.
This update is to remove the ones from CPU_AP_DATA and update MpInitLib to
consume the ones from CPU_INFO_IN_HOB.
V2:
Fixed potential un-initialized variable issue.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If BSP found APs timeout happened when AP executing AP task, BSP will reset APs
by WakeUpAP(). However, if ApLoopMode is ApMwaitLoop or ApRunLoop, WakeUpAp()
will try to write semaphore in memory to wake up AP. It cannot wake up APs
actually if APs still executing AP task.
This fix is to set ApInitReconfig flag to force BSP to send INIT-SIPI-SIPI to
wake up APs.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Cr3Location offset value should be 0x34 not 0x3C.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Zeng Star <star.zeng@intel.com>
We will put APs into hlt-loop in safe code. But we decrease mNumberToFinish
before APs enter into the safe code. Paolo pointed out this gap.
This patch is to move mNumberToFinish decreasing to the safe code. It could
make sure BSP could wait for all APs are running in safe code.
https://bugzilla.tianocore.org/show_bug.cgi?id=216
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
On S3 path, we may transfer to long mode (if DXE is long mode) to restore CPU
contexts with CR3 = SmmS3Cr3 (in SMM). AP will execute hlt-loop after CPU
contexts restoration. Once one NMI or SMI happens, APs may exit from hlt state
and execute the instruction after HLT instruction. If APs are running on long
mode, page table is required to fetch the instruction. However, CR3 pointer to
page table in SMM. APs will crash.
This fix is to disable long mode on APs and transfer to 32bit protected mode to
execute hlt-loop. Then CR3 and page table will no longer be required.
https://bugzilla.tianocore.org/show_bug.cgi?id=216
Reported-by: Laszlo Ersek <lersek@redhat.com>
Analyzed-by: Paolo Bonzini <pbonzini@redhat.com>
Analyzed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
On S3 path, we will wake up APs to restore CPU context in PiSmmCpuDxeSmm
driver. However, we place AP in hlt-loop under 1MB space borrowed after CPU
restoring CPU contexts.
In case, one NMI or SMI happens, APs may exit from hlt state and execute the
instruction after HLT instruction. But the code under 1MB is no longer safe at
that time.
This fix is to allocate one ACPI NVS range to place the AP hlt-loop code. When
CPU finished restoration CPU contexts, AP will execute in this ACPI NVS range.
https://bugzilla.tianocore.org/show_bug.cgi?id=216
v2:
1. Make stack alignment per Laszlo's comment.
2. Trim whitespace at end of end.
3. Update year mark in file header.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Analyzed-by: Paolo Bonzini <pbonzini@redhat.com>
Analyzed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Currently, DxeMpLib only places APs into specified c-state in Exit Boot Service
callback function for UEFI OS boot. We need to put APs into specified c-state
for legacy OS boot also.
https://bugzilla.tianocore.org/show_bug.cgi?id=210
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Rename MpInitExitBootServicesCallback() to MpInitChangeApLoopCallback() because
it will not only be invoked on Exit Boot Service Event, but also will be invoked
on Legacy Ready To Boot Event.
https://bugzilla.tianocore.org/show_bug.cgi?id=210
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Current implementation just allocates reserve memory for AsmRelocateApLoopFunc.
It not be safe because APs will be placed into 32bit protected mode on long mode
DXE. This reserve memory must be located below 4GB memory.
This fix is to allocate < 4GB memory for AsmRelocateApLoopFunc.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
[lersek@redhat.com: strip whitespace at EOL]
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
If MaxLogicalProcessorNumber is only 1, we needn't to wake up APs at all
and needn't to register callback functions.
It could improve boot performance on single supported system.
https://bugzilla.tianocore.org/show_bug.cgi?id=204
Cc: Feng Tian <feng.tian@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Dump new stack base and size information could help developer to narrow down
stack crash issue.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This folder provides the sample build for Microcode FMP.
The DSC/FDF is to convert the Microcode binary/text to Microcode FMP.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
MicrocodeUpdate supports update Microcode region via UEFI FMP capsule.
MicrocodeUpdate SetImage() will perform the Microcode version,
ProcessorSignature/ProcessorFlag, and try to load microcode.
If and only if the Microcode is loaded successfully, and new Microcode
will be updated to system flash region.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Add NULL instance to pass build.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
This library is used to abstract microcode flash region access.
This library is consumed by a microcode capsule update module.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
It defined ImageTypeId for Microcode.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Add Microcode capsule related component to check build.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
All CpuExceptionHandlerLib library instances use nasm source files.
Cc: Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
We need to add EFIAPI for all interface service including library API.
Contributed-under: TianoCore Contribution Agreement 1.0
Cc: Leo Duran <leo.duran@amd.com>
Cc: Michael Kinney <Michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
GetProcessorLocation() is too generic and will conflict with the API defined in
Galileo Board Software Package v1.0.0.
This update is just to rename GetProcessorLocation() to one specific name
GetProcessorLocationByApicId().
Contributed-under: TianoCore Contribution Agreement 1.0
Cc: Leo Duran <leo.duran@amd.com>
Cc: Michael Kinney <Michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
1) Remove SmmGetProcessorLocation() from PiSmmCpuDxeSmm driver.
2) Remove ExtractProcessorLocation() from MpInitLib library.
3) Add GetProcessorLocation() to BaseXApicLib and BaseXApicX2ApicLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Signed-off-by: Michael Kinney <Michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
while-loop check should not co-exist with for-loop. This should be typo when we
check-in the original code. We should keep one loop only.
This issue caused CLANG38 build failure reported by
https://tianocore.acgmultimedia.com/show_bug.cgi?id=148
Contributed-under: TianoCore Contribution Agreement 1.0
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Currently, this is ASSERT() if neither SecPlatformInformation2 nor
SecPlatformInformation PPIs are found. This is not correct. Per PI specification
both of them are optional PPI. Platform may not install them.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Revert SecPlatformInformation2 and SecPlatformInformation in two comment blocks.
And correct the words.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
In SecTemporaryRamDone(), we will build one privated GUIDed-HOB to save CPU BIST
Data and re-install SEC platform information(2) PPI. Then other PEI drivers
could get CPU BIST data from the private GUIDed-HOB by new installed PPI.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Abstract one worker function to get CPU BIST from the GUIDed-HOB. Add
SecPlatformInformationBist() and SecPlatformInformation2Bist() to invoke
GetBistFromHob(). Add in/out for parameter in function header.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Add SecBist.c and copy GetBistInfoFromPpi() and SecPlatformInformation2() from
UefiCpuPkg/CpuMpPei/CpuBist.c. And update SecMain.c, SecMain.inf and
UefiCpuPkg.dsc accordinlgy to pass build.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Build gEfiSecPlatformInformation2PpiGuid GUIDed-HOB to store all CPU BIST data
that could be used not only by SecPlatformInformation2(), but also by CPU MP Dxe
driver to get CPU BIST data.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
ProcessorInfo.ProcessorId is UINT64 type even it's valid value is UINT32. Use %x
only output the low 4 bytes and keep the high 4 bytes in stack that will be
output as the second parameter BistData. Typecast ProcessorInfo.ProcessorId to
UINT32 could make BistData output correctly.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
If CPU Bist data is not zero, we will report Status code. But there is one bug
that will report each processor's status code duplicated with NumberOfData
times. This fix is to exchange the loop order on NumberOfData and
mNumberOfProcessors. It could make sure the report status code only once for
each processor.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
if PcdAcpiS3Enable is disabled, then skip S3 related logic.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
If PcdAcpiS3Enable is disabled, then return an EFI_UNSUPPORTED
error which forces the module to be unloaded.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
In Exit Boot Services callback function, we cannot use allocate memory services
because it may change the memory map that has been gotten by OS.
This fix is not to allocate reset vector buffer after SaveRestoreFlag is set to
TRUE in MpInitExitBootServicesCallback(). Instead AllocateResetVector() will use
the previous allocated buffer address and save the contents before copying reset
vector code. At the same time, FreeResetVector() will restore original contents
after if SaveRestoreFlag is TRUE.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Just move BackupAndPrepareWakeupBuffer() and RestoreWakeupBuffer() from
PeiMpLib.c to MpLib.c.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
It will be used by DxePeiLib also.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In Exit Boot Services callback function, we cannot use allocate memory services
because it may change the memory map that has been gotten by OS.
This fix is to move allocating reserved memory for AP loop code to
InitMpGlobalData() and save the memory address in one global variable.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
After sending the 1st broadcast INIT-SIPI-SIPI, BSP will collect APs count after
one specified timeout delay. However, WakupAp() will restore reset vector
immediately after sending 1st broadcast INIT-SIPI-SIPI. Some processors may not
complete executing reset vector code.
This fix is to move MicroSecondDelay() from CollectProcessorCount() to the place
that is after sending 1st broadcast INIT-SIPI-SIPI and before FreeResetVector()
in WakupAp().
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
PiSmmCpuDxeSmm driver's entry point will get some PCDs supported dynamic type.
In case those PCDs are set as DynamicHii type in platform DSC File, it implies
that EFI Variable Arch protocol is required.
This fix is to add gEfiVariableArchProtocolGuid dependency on PiSmmCpuDxeSmm
driver to make sure those DynamicHii PCDs could be read correctly.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v5:
If PcdCpuMaxLogicalProcessorNumber is set to 1 on UP system,
MpInitLibInitialize() will be invoked. This is one bug, we need to
call MpInitLibInitialize() always and get the BSP information.
Just to remove PcdCpuMaxLogicalProcessorNumber() consuming from this
driver.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Consume MP Initialize library to produce CPU MP Protocol services to simply the
code.
v4:
1. Update CpuDxe.c file header to mention it produces CPU Arch protocol.
2. Update BistData type from UINT32 to EFI_HEALTH_FLAG.
3. Move some header location from CpuMp.h to CpuDxe.h.
v3:
1. Move the code Consume MpInitLib APIs to produce CPU MP Protocol from patch
#40 to this patch.
2. Add DxeMpInitLib.inf in DSC file
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Consume MP initialize library to produce CPU MP PPI, it could simply the code.
Add STATIC for some internal functions to avoid build issue with the same
functions name in PeiMpInit instance. They will be removed by the next patch.
v4:
1. Update BistData type from UINT32 to EFI_HEALTH_FLAGS.
v3:
1. Rename MpInitLibSwitchBSP to MpInitLibSwitchBSP
2. Add PeiMpInitLib.inf in DSC file
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Register Exit Boot Service callback function MpInitExitBootServicesCallback() to
place AP one safe loop before hand-off to OS.
Allocated one reserved memory and copy the AsmRellocateApLoop() code into it. It
could avoid the CPU Dxe driver (located in Boot Service data range) crashed
after Exit Boot Service event.
Place AP into the target Cx-State (specified by PcdCpuApTargetCstate) could save
power if Monitor-mwait feature supported.
In long mode, switch AP into protected mode could let AP not require page table
when executing this safe loop. Page Table (located in Boot Service data range)
may crashed after Exit Boot Service event.
v3:
1. Rename *RellocateAp* to *RelocateAp*
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v4:
1. Simply the internal function StartupAllAPsWorker()'s function
header due to it is duplicated with MpInitLibStartupAllAPs().
v3:
1. Use CamelCase for mStopCheckAllApsStatus and
CheckAndUpdateApsStatus()
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v4:
1. Simply the internal function StartupThisAPWorker()'s comment
header due to it is duplicated with MpInitLibStartupThisAP().
v3:
1. Use CamelCase for mStopCheckAllApsStatus and
CheckAndUpdateApsStatus().
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v4:
1. Simply the internal function MpInitLibEnableDisableAP()'s function
header due to it is duplicated with MpInitLibEnableDisableAP().
v3:
1. Use CamelCase for mCheckAllAPsEvent, mStopCheckAllApsStatus.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v4:
1. Simply the internal function SwitchBSPWorker()'s comment header
due to it is duplicated with MpInitLibSwitchBSP().
v3:
1. Rename MpInitLibSwitchBsp to MpInitLibSwitchBSP.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v5:
1. Remove (-1) and use the clean code to calculate the Location->Thread
and Location->Core.
v4:
1. Update HealthData type from UINT32 to EFI_HEALTH_FLAGS
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
If GUIDed HOB mCpuInitMpLibHobGuid exists, we could get the processor count and
processor APICID and Initial APICID from CPU_INFO_IN_HOB. We needn't to delay
for broadcast INIT-SIPI-SIPI results and could improve performance.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
If x2APIC flag is set, enable x2APIC mode on all APs and BSP. Before we wakeup
APs to enable x2APIC mode, we should wait all APs have finished initialization.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
CollectProcessorCount() will send the 1st INIT-SIPI-SIPI to get processor count
in system.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
WakeUpAP() is used to wakeup APs per current ApLoopMode and make sure APs wake
up successfully.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
FillExchangeInfoData() is used to fill MP_CPU_EXCHANGE_INFO date exchanged
between C code and assembly code of AP reset vector.
v5:
1. Reference ApWakeupFunction instead of ApCFunction.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
ApWakeupFunction() is the first C function executed from AP reset vector. When
APs waken up at the first time, it will sync BSP's MTRR setting and load
microcode on APs and collect APs' BIST information.
When AP tasked finished, it will place APs it one loop specified by ApLoopMode.
v5:
1. Rename ApCFunction to ApWakeupFunction to meet naming convention.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
In PeiMpInitLib, searching unallocated memory under in
EFI_HOB_TYPE_RESOURCE_DESCRIPTOR hobs to find the memory under 1MB for AP reset
vector. After End of PEI event triggered, we need to restore original the buffer
contents to avoid crash the OS on S3 boot.
In DxeMpInitLib, allocate the memory under 1MB for AP reset vector.
Add helper functions AllocateResetVector()/FreeResetVector() used by WakeupAp().
v3:
1. Move SetTimer() from Patch #17 to Patch 16.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
In DxeMpInitLib, register one period event callback function CheckAPsStatus()
used to check AP Status.
v5:
1. Introduce AP_CHECK_INTERVAL for adjust AP check timer interval potential.
v3:
1. Use CamelCase for mCheckAllAPsEvent, mStopCheckAllApsStatus and
CheckAndUpdateApsStatus().
2. Move SetTimer() from Patch #17 to Patch 16.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
In PeiMpInitLib, register End of PEI callback function CpuMpEndOfPeiCallback().
v5:
1. Add comment block for mMpInitLibNotifyList.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
In PeiMpInitLib, save CPU MP Data pointer into one local Guided HOB.
In DxeMpInitLib, save CPU MP Data pointer into one global variable.
Add helper functions GetCpuMpData()/SaveCpuMpData().
v5:
1. Move CPU_INIT_MP_LIB_HOB_GUID from MpLib.c to MpLib.h to make
all C files visible.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Add CPU_VOLATILE_REGISTERS definitions for CRx and DRx required to be restored
after APs received INIT IPI.
Add worker functions SaveVolatileRegisters()/RestoreVolatileRegisters() used to
save/restore CRx and DRx. It also check if Debugging Extensions supported or
not.
v5:
1. Add comment block for structure CPU_VOLATILE_REGISTERS.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Initialize CPU_AP_DATA for CPU APs and add GetApState()/SetApState() helper
functions to get/set AP state.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
v5:
1. Add comment block for enum AP_INIT_STATE and structure CPU_AP_DATA.
2. Add more comment for structure CPU_INFO_IN_HOB.
3. Add more clarification in structure _CPU_MP_DATA for those fields
pass from PEI to DXE.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Firstly, get ApLoopMode from PcdCpuApLoopMode. If MonitorMwait feature is not
supported, update ApLoopMode to ApHltLoop. If MonitorMwait feature is supported,
get MointorFilter size by CPUID.[EAX=05H]:EBX.BIT0-15.
v5:
1. Add comment block for enum AP_LOOP_MODE.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
In MpInitLibInitialize(), invoke AsmGetAddress() to get get assembly functions'
entry addresses and the sizes from returned MP_ASSEMBLY_ADDRESS_MAP structure.
v5:
1. Add more detailed comments for structure MP_ASSEMBLY_ADDRESS_MAP.
v4:
1. Add AsmRelocateApLoop information return in AsmGetAddress().
v3:
1. Rename AsmRellocateApLoop to AsmRelocateApLoop.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
AsmRelocateApLoop() is used to place APs into MWAIT-loop if MonitorMwait
feature is supported before hand-off to OS, or place APs into HLT-loop if
MonitorMwait feature is not supported.
If the current mode is long mode, we will switch APs to protected mode
before placing APs in MWAIT-loop or HLT-loop. Thus, once APs wakeup from
loop, APs needn't the page table that may be crashed by OS.
v3:
1. Rename AsmRellocateApLoop to AsmRelocateApLoop.
2. Fix typo Proteced to Protected.
3. Fix typo segement to segment
4. Use word MONITOR instead of mwait-monitor.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
EnableExecuteDisable in MP_CPU_EXCHANGE_INFO is used to tell AP reset vector if
enable execute disable feature on APs. This feature should be enabled before CR3
is written.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Add assembly code for AP reset vector and the definition of MP_CPU_EXCHANGE_INFO
that are used to exchange the data between C code and assembly code when AP wake
up.
v4:
1. Copy MP_CPU_EXCHANGE_INFO from UefiCpuPkg/CpuMpPei/CpuMpPei.h
2. Copy MpEqu.inc and MpFuncs.nasm from UefiCpuPkg/CpuMpPei.
v3:
1. Rename NumApsExecutingLoction to NumApsExecutingLocation
2. Add whitespace after ; in .nasm file
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Add two MP Initialize Library instances PeiMpInitLib.inf and DxeMpInitLib.inf
with NULL implementation.
One PeiMpInitLib.inf is consumed by PEI MP driver. Another DxeMpInitLib.inf is
consumed by DXE MP driver.
Place MpInitLibStartupAllAPs()/MpInitLibStartupThisAp()/MpInitLibSwitchBSP()/
MpInitLibEnableDisableAP() into PeiMpLib.c and DxeMpLib.c, because they have
the different implementations and will be updated in latter patches.
v5:
1. Add back PeiExceptionHandlerLib.inf in UefiCpuPkg.dsc. It is removed
incorrectly.
v4:
1. Return EFI_UNSUPPORTED instead of EFI_SUCCESS for NULL implementation of
all Functions.
2. Sync MpInitLibxxx functions header updating described in v4 part of Patch
#4.
v3:
1. Rename MpInitLibSwitchBsp to MpInitLibSwitchBSP to match PI spec
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
MP Initialize library provides basic functionalities to do APs initialization,
to manage MP information and to wakeup APs to execute AP task.
It could be consumed by CPU MP PEI or DXE drivers to provide CPU MP PPI/Protocol
services.
v4:
1. MpInitLibGetProcessorInfo():
Update HealthData type from UINT32 to EFI_HEALTH_FLAGS.
Add #include <Ppi/SecPlatformInformation.h>
2. MpInitLibSwitchBSP():
Return EFI_DEVICE_ERROR instead of EFI_SUCCESS if the calling processor is
an AP.
3. MpInitLibStartupThisAP():
Fix several incorrect references to "APs" to match PI spec.
4. MpInitLibSwitchBSP() and MpInitLibEnableDisableAP():
Fix incorrect description on ProcessorNumber.
5. Trim whitespace at end of line.
v3:
1. Add whitespace after MpInitLibInitialize
2. Rename MpInitLibSwitchBsp to MpInitLibSwitchBSP to match PI spec
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Currently, we will allocate StartupVector buffer under 1MB at entry point
function. But some modules may allocate some hard code address under 1MB.
For example, LegacyBiosDxe driver tries to manage some legacy range under
640KB.
To avoid the conflicts, we move StartupVector buffer allocation to End Of
DXE event callback function.
v4:
Update the Context parameter is used as a pointer to AcpiCpuDataEx, then
we needn't to add the global variable.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Add microcode definitions defined in Intel(R) 64 and IA-32 Architectures
Software Developer's Manual Volume 3A, Section 9.11.
v4:
1. ProcessorSignature type changed to CPU_MICROCODE_PROCESSOR_SIGNATURE
2. Add pack(1) for structure CPU_MICROCODE_HEADER and
CPU_MICROCODE_EXTENDED_TABLE.
v3:
1. Update SDM date to June, 2016
2. Mention BCD format in CPU_MICROCODE_DATE
3. Rename ProcessorChecksum to Checksum to match SDM.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
#define MSR_IA32_APIC_BASE_ADDRESS is duplicated with #define MSR_IA32_APIC_BASE
defined in UefiCpuPkg/Include/Register/ArchitecturalMsr.h, so we could remove it
and update the modules to use MSR_IA32_APIC_BASE from ArchitecturalMsr.h.
Structure MSR_IA32_APIC_BASE conflicts with #define MSR_IA32_APIC_BASE defined
in UefiCpuPkg/Include/Register/ArchitecturalMsr.h, so we could remove it and
update the modules to use structure MSR_IA32_APIC_BASE_REGISTER from
ArchitecturalMsr.h.
v5:
1. Update SourceLevelDebugPkg to use APIC Base MSR from ArchitecturalMsr.h.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Add the following definition in the [BuildOptions] section in package DSC
files to disable APIs that are deprecated:
[BuildOptions]
*_*_*_CC_FLAGS = -D DISABLE_NEW_DEPRECATED_INTERFACES
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
The commit 8b9311 changed the zeroing of mSmmMpSyncData of type
SMM_DISPATCHER_MP_SYNC_DATA by the following patch.
- ZeroMem (mSmmMpSyncData, mSmmMpSyncDataSize);
+ mSmmMpSyncData->SwitchBsp = FALSE;
mSmmMpSyncDataSize not only includes SMM_DISPATCHER_MP_SYNC_DATA, but
also includes the SMM_CPU_DATA_BLOCK array and one BOOLEAN variable
array as shown here:
mSmmMpSyncDataSize = sizeof (SMM_DISPATCHER_MP_SYNC_DATA) +
(sizeof (SMM_CPU_DATA_BLOCK) + sizeof (BOOLEAN)) *
gSmmCpuPrivate->SmmCoreEntryContext.NumberOfCpus;
This patch restores the original ZeroMem() to clear all CPU Sync data.
The commit 8b9311 may cause unexpected behavior.
v2:
Mentioned CandidateBsp array in comments to make it more accurate.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
SetMemoryAttributes() will sync BSP's MTRRs settings to all APs by StartupAllAPs
service in serial mode. It may caused much performance impact if there are too
much processors in system. This update is to invoke StartupAllAps in parallel
mode. IA32 SDM does suggest to program MTRRs in parallel mode.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Except for MtrrSetAllMtrrs(), others services are not suggested to be invoked by
APs because they are not necessary and may invoke DEBUG() to dump MTRR setting.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed: Laszlo Ersek <lersek@redhat.com>
MtrrSetAllMtrrs() maybe used by APs to sync BSP's MTRR settings. BSP's MTRR
setting should be displayed if EFI_D_CACHE flag is set when MTRR updated. In
MtrrSetAllMtrrs(), it's not necessary to display MTRR setting again due to the
MTRR settings should be always same among BSP/APs. This updating could avoid
APs output MTRR setting at the same time and make display message corrupted.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Commits 28ee581646 and 246cd9085f added these ENDs as part of the
manual conversion from *.asm files. However, the ENDs makes no sense for
NASM. Although they don't break the build, NASM complains about them:
label alone on a line without a colon might be in error
(This NASM warning category dates back to NASM 0.95, commit
6768eb71d8deb.)
Remove the ENDs.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
CheckProcessorFeature() invokes MpService->StartupAllAps() to detect
XD/BTS features on normal boot path. It's not necessary and may cause
performance impact, because INIT-SIPI-SIPI must be sent to APs if APs
are in hlt-loop mode. XD/BTS feature detection is moved to
SmmInitHandler() in SMM relocation during normal boot path.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
It will be set to TRUE during S3 resume.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
REGISTER_TYPE in UefiCpuPkg/Include/AcpiCpuData.h defines a MemoryMapped
enum value. However support for the MemoryMapped enum is missing from
the implementation of SetProcessorRegister(). This patch adds support
for MemoryMapped type SetProcessorRegister().
One spin lock is added to avoid potential conflict when multiple processor
update the same memory space.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
InitializeMpSyncData() invokes InitializeSmmCpuSemaphores() to allocate an
aligned buffer for all locks and semaphores. However, this function is
invoked on S3 resume path again to reset mSmmMpSyncData. It causes
an additional aligned buffer to be allocated.
This update moves InitializeSmmCpuSemaphores() into
InitializeMpServiceData() that is only invoked on normal boot.
InitializeMpSyncData() is updated to reset the locks/semaphore in
mSmmMpSyncData.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Hao Wu
Leo Duran
Jeff Fan
Jiewen Yao
Dandan Bi
Michael Kinney
Feng Tian
Laszlo Ersek
Liming Gao
Gary Lin
Star Zeng
Ruiyu Ni