REF: https://bugzilla.tianocore.org/show_bug.cgi?id=313
Add PcdPcieResizableBarSupport to enable/disable PCIe Resizable
BAR Capability fearture.
Program the Resizable BAR Register if the device suports PCIe Resizable
BAR Capability and PcdPcieResizableBarSupport is TRUE.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Heng Luo <heng.luo@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=3114
Add logic to flush all UART transmit buffers if there is a
config change from Reset(), SetAttributes() or SetControl().
Use a timeout in the flush operation, so the system can
continue to boot if the transmit buffers can not be
flushed for any reason.
This change prevents lost characters on serial debug logs
and serial consoles when a config change is made. It also
prevents a UART from getting into a bad state or reporting
error status due to characters being transmitted at the same
time registers are updated with new communications settings.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
With some super-speed USB mass storage devices it has been observed
that a USB transaction error may occur when attempting the set the
device address during enumeration.
According the the xHCI specification (section 4.6.5) ...
"A USB Transaction ErrorCompletion Code for an Address Device Command
may be due to a Stall response from a device. Software should issue a
Disable Slot Commandfor the Device Slot then an Enable Slot Command
to recover from this error."
To fix this, retry the device slot initialization if it fails due to a
device error.
Change was verified using a superspeed mass storage device that was
occasionally failing to enumerate in UEFI. With this change this failure
to enumerate was resolved. This failure was also only seen in UEFI and not
in the OS.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3007
Currently UsbDevContext is not cleaned up if USB slot initialization is
failed, the wrong context data will affect next USB devices and
the USB devices can not be enumerated.
Need to disable slot if USB slot initialization is failed.
Below test cases are passed on UpXtreme:
a. USB 3.0 thumb drives can be recognized in UEFI shell
b. SUT can boot to Puppylinux from USB3.0 mass storage,
the storage can be recognized in linux
c. Plug in a USB keyboard (hot plug) and enumeration is OK
in UEFI shell and linux
d. Plug in a USB mouse(hot plug) and enumeration is OK in linux.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Heng Luo <heng.luo@intel.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2948
Timeouts in the XhciDxe driver are taking longer than
expected due to the timeout loops not accounting for
code execution time. As en example, 5 second timeouts
have been observed to take around 36 seconds to complete.
Use SetTimer and Create/CheckEvent from Boot Services to
determine when timeout occurred.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Patrick Henz <patrick.henz@hpe.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Add check for NULL HostAddress in AllocateBuffer as required by UEFI
specification.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1959
Replaces usage of the linked list iteration macros defined in Xhci.h
with the common definition in BaseLib.h.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Guomin Jiang <guomin.jiang@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Bret Barkelew <bret.barkelew@microsoft.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1959
Replaces usage of the linked list iteration macros defined in EhcPeim.h
with the common definition in BaseLib.h.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Guomin Jiang <guomin.jiang@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Bret Barkelew <bret.barkelew@microsoft.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1959
Replaces usage of the linked list iteration macros defined in Ehci.h
with the common definition in BaseLib.h.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Guomin Jiang <guomin.jiang@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Bret Barkelew <bret.barkelew@microsoft.com>
NonDiscoverablePciDeviceDxe currently #defines the module-internal
PCI_MAX_BARS macro, with value 6 (and type "int").
Remove this private macro definition, and adopt PCI_MAX_BAR from
"MdePkg/Include/IndustryStandard/Pci22.h". Both the value and the type
remain unchanged (the standard PCI_MAX_BAR macro expands to 0x0006).
"NonDiscoverablePciDeviceIo.h" gets the definition of PCI_MAX_BAR via its
existent #include <IndustryStandard/Pci.h> directive.
Build-tested only.
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200409113017.18233-1-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
ASSERT in PollMem_Conf, CopyMem_Conf, SetBarAttributes_Conf
Conformance Test.
SCT Test expect return as Invalid Parameter or Unsupported.
Added Checks for Function Parameters.
return Invalid or Unsupported if Check fails.
Added Checks in PciIoPollIo(), PciIoIoRead()
PciIoIoWrite()
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Current driver does not support PIO transfer mode for
commands other then tuning. This change adds the code
to transfer PIO data.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Driver code used to map memory for DMA transfer even if host doesn't
support DMA. This is causing memory corruption when driver transfers
data using PIO. This change refactors the code to skip call to
PciIo->Map for non DMA transfers.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
This patch refactors the way in which the driver will check
the data transfer completion. Data transfer related
functionalities have been moved to separate function.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
SdMmcPciHcDxe driver used to read response only after
command and data transfer completed. According to SDHCI
specification response data is ready after the command
complete status is set by the host controller. Getting
the response data early will help debugging the cases
when command completed but data transfer timed out.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
To allow for easier debug of failing commands we
have added a capability to print TRB and command
packet when we start execution of the TRB(on
DEBUG_VERBOSE level) and when the TRB failed to
execute correctly(on DEBUG_ERROR level). Additionally
we will also print error interrupt status and interrupt
status register on failed SD command.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1140
To avoid stability issues on some designs the driver
will now send SEND_STATUS at previous, lower, frequency
when upgrading the bus timing.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1989
The commit will avoid unmapping the same resource in error handling logic
for function BuildAdmaDescTable() and SdMmcCreateTrb().
For the error handling in BuildAdmaDescTable():
The error is directly related with the corresponding Map() operation
(mapped address beyond 4G, which is not supported in ADMA), so the Unmap()
operation is done in the error handling logic, and then setting
'Trb->AdmaMap' to NULL to avoid double Unmap.
For the error handling in SdMmcCreateTrb():
The error is not directly related with the corresponding Map() operation,
so the commit will update the code to left SdMmcFreeTrb() for the Unmap
operation to avoid double Unmap.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2515
Change the MdeModulePkg to match the ECC check rule
Signed-off-by: GuoMinJ <newexplorerj@gmail.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
This patch adds retries for async execution for commands that
failed due to the CRC errors.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1140
To increase the resiliency driver will now attempt to
retry the commands that failed due to the CRC error up
to 5 times. This should address the problems with the commands
that fail due to random condition on links. This should also
help the boards on which CMD13 is particularly unstable after
switching the link frequency.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1140
Error detection function will now check if the command
failure has been caused by one of the errors that can
appear randomly on link(CRC error + end bit error). If
such an error has been a cause of failure, function will
return EFI_CRC_ERROR instead of EFI_DEVICE_ERROR to indicate
to the higher level that command has a chance of succeeding if
resent.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Driver used to reset the DAT lane on a current error which
is not required according to SD specification(it's not going
to help). This patch will reset the DAT lane only on DAT
lane specific errors.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Changed @rtval to @retval in SdMmcHcStartSdClock
function description.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
In SD card voltage switch flow we used to redo the
entire internal clock setup after voltage switch.
Since internal clock has already been setup this
is wasting time on polling the internal clock stable.
This commit changes it to only start the SD clock.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
For eMMC modules we used to notify the platform about frequency
change only after sending CMD13 which meant that platform
might not get a chance to apply required post frequency
change fixes to get the clock stable. To fix this
notification has been moved to SdMmcHcClockSupply function
just after we start the SD clock. During first time setup
the notification won't be sent to avoid changing old behavior.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2118
When a packet is queued/completed for the asynchronous IO queue, the logic
to roll over to the front of the queue doesn't account for actual size of
the IO Submission/Completion queue.
This causes a device to hang due to doorbell being outside of visible
queue. An example would be if an NVMe drive only supported a queue size of
128 while the driver supports 256.
Cc: Jian J Wang <jian.j.wang@intel.com>
Signed-off-by: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Acked-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2303
Whenever a PCI device is discovered, PCI bus calls the
EDKII_DEVICE_SECURITY_PROTOCOL to authenticate it.
If the function returns success, the PCI bus allocates
the resource and installs the PCI_IO for the device.
If the function returns fail, the PCI bus skips the device.
It is similar to EFI_SECURITY_ARCH_PROTOCOL, which
is used to verify an EFI image.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Yun Lou <yun.lou@intel.com>
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
RequestMap is used but not Initialized.
RequestMap is called by UhciMapUserRequest, in which RequestMap(Map)
is called by IoMmuMap, and is finally called by IoMmu->Map.
We can not assume RequestMap is given an initial value at any step.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Map is used but not Initialized.
Map is called by IoMmuMap, in which Mapping(Map) is called by IoMmu->Map.
We can not assume Map is given an initial value at any step.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2312
This patch is for fixing unexpected system hang during S3 unlock process.
FatPei driver maintained and updated internal BlockIo devices list
when there is new BlockIo PPI has installed, and it relied on BlockIo PPI
service to get data from devices. Because BlockIo Ppi leverage
NvmExpressPei Ppi to transit Nvm command to device, we should make sure
NvmePassThruPpi installed before BlockIo PPI.
Signed-off-by: Maggie Chu <maggie.chu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Add support for allocating aligned pages at an alignment higher
than 4K. The new function allocated memory taking into account
the padding required and then frees up unused pages before mapping
it.
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
While allocating pages aligned at an alignment higher than
4K, allocate memory taking into consideration the padding
required for that alignment. The calls to free pages takes
care of this already.
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Unlike the InstallMultipleProtocolInterfaces() boot service, which takes
an (EFI_HANDLE*) as first parameter, the
UninstallMultipleProtocolInterfaces() boot service takes an EFI_HANDLE as
first parameter.
These are actual bugs. They must have remained hidden until now because
they are on error paths. Fix the UninstallMultipleProtocolInterfaces()
calls.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2218
There is a bug in current driver code that makes
it impossible for it to work with devices that
only work in legacy speed mode since the function
EmmcSwitchToHighSpeed will return with EFI_INVALID_PARAMETER
for such bus mode. Since the logic in that function will
work well for SdMmcMmcLegacy this patch just allows
to call this function with SdMmcMmcLegacy bus mode.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2218
SD specification recommends switching card bus timing before
switching bus timing in controller. Emmc driver used to do
this switch other way around. This commit adds controller
timing switch in EmmcSwitchBusTiming function to enforce this
order and removes all controller timing programming from
EmmcSwitchToXXX functions.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2218
Stopping the SD clock before switching host controller
bus timing is only necessary if preset value enable is
set in host controller. Code that performs switch to
HS200 doesn't check this condition right now and we also
don't do the SD clock stop before any other bus timing switch
in host controller. Since the driver is generally not ready to support
host controller with preset value enable set we removed this
code.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=1796
Bug fixed in PciBusDxe\PciLib.c.
Removed the redundant second call to PciSearchDevice sub-routine when the
PCD for the Hot-Plug support is disabled.
Signed-off-by: Ashraf Javeed <Ashraf.javeed@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=1882
Implement support for GetOperatingParamters notify phase
in SdMmcHcDxe driver. GetOperatingParameters notify phase
is signaled before we start card detection and initialization.
Code has been updated for both eMMC and SD card controllers to
take into consideration those new parameters. Initialization process
has been divided into 2 steps. In the first step we bring the link
up to the point where we can get card identification data(Extended
CSD in eMMC case and SWITCH command response in SD card case). This
data is later used along with controller capabilities and operating
parameters passed in GetOperatingParameters phase to choose preferred
bus settings in GetTargetBusSettings function. Those settings are later
on to start bus training to high speeds. If user passes incompatible
setting with selected bus timing driver will assume it's standard behavior
with respect to that setting. For instance if HS400 has been selected as a
target bus timing due to card and controller support bus width setting of
4 and 1 bit won't be respected and 8 bit setting will be chosen instead.
Tests on Marvell boards were also performed by Marcin Wojtas
<mw@semihalf.com>:
https://edk2.groups.io/g/devel/message/42999
Board 1 (out of tree): SD - OK, MMC - OK
Board 2: (Armada80x0McBin): SD - OK, MMC - OK
Board 3: (Armada70x0Db): SD - problems, MMC - OK
Please note that the problem on Armada70x0Db SD devices are introduced by
adding new types of SD bus modes, a subsequent patch within edk2-platforms
repository will be proposed to address it.
(More details can be referred from the above link.)
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Regression-tested-by: Sumit Garg <sumit.garg@linaro.org>
https://bugzilla.tianocore.org/show_bug.cgi?id=1879
This commit will add codes to produce the NVM Express PassThru PPI.
Signed-off-by: Maggie Chu <maggie.chu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
When assigning a physical PCIe device to a QEMU/KVM guest, PciBusDxe may
find that the extended config space is not (fully) implemented. In
LocatePciExpressCapabilityRegBlock(), "CapabilityEntry" may be read as
0xFFFF_FFFF at a given config space offset, after which the loop gets
stuck spinning on offset 0xFFC (the read at offset 0xFFC returns
0xFFFF_FFFF most likely as well).
Another scenario (not related to virtualization) for triggering the above
is when a Conventional PCI bus -- exposed by a PCIe-to-PCI bridge in the
topology -- intervenes between a PCI Express Root Port and a PCI Express
Endpoint. The Conventional PCI bus limits the accessible config space of
the PCI Express Endpoint, even though the endpoint advertizes the PCI
Express capability. Here's a diagram, courtesy of Alex Williamson:
[PCIe Root Port]--[PCIe-to-PCI]--[PCI-to-PCIe]--[PCIe EP]
->| |<- Conventional PCI bus
Catch reads of 0xFFFF_FFFF in LocatePciExpressCapabilityRegBlock(), and
break out of the scan with a warning message. The function will return
EFI_NOT_FOUND.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
DEPEX from PEI storage stack.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1777
BootInRecoveryMode Ppi dependency should be removed from PEI storage stack
drivers. Besides recovery, more features are using the storage stack.
Platform can apply Ppi dependency in Recovery FV which contains full
storage driver stack. Platform storage stack modules, such as host
controller init PEI module, should also remove this dependency.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1460
Refer to Uefi spec 2.8, the ResetData is valid while ResetStatus
is EFI_SUCCESS regardless of the ResetType is EfiResetPlatformSpecific
or not. So change the comments of NvmeShutdownAllControllers.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Michael Turner <Michael.Turner@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Delete the explicit machine type check for option ROM images, and instead,
rely on the LoadImage() boot service to decide whether an option ROM can
be dispatched or not. This permits platforms to ship with emulators to
execute option ROMs that are not native to the processor architecture.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Driver was supporting only 32b DMA support for V3 controllers. Add
support for 64b DMA as well for completeness.
For V4.0 64b support, driver was looking at incorrect capability
register bit. Fix for that is present as well.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1583
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Tested-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
For the NvmExpressPei driver, this commit will update the driver to
consume the S3StorageDeviceInitList LockBox in S3 phase. The purpose is to
perform an on-demand (partial) NVM Express device
enumeration/initialization to benefit the S3 resume performance.
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
For the NvmExpressPei driver, this commit will add codes to produce the
Storage Security Command PPI if the underlying NVM Express controller
supports the Security Send and Security Receive commands.
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This commit is out of the scope for BZ-1409. The commit will remove the
call of RegisterForShadow() at the entry point of the driver. By doing so,
the driver is now possible to be executed without being re-loaded into
permanent memory.
Thus, this commit will update the NvmExpressPei driver to avoid updating
the content of a global variable.
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1537
Use 16-bit and 32-bit IO widths for SDMMC MMIO to prevent all register
accesses from being split up into 8-bit accesses.
The SDHCI specification states that the registers shall be accessible in
byte, word, and double word accesses. (SD Host Controller Simplified
Specification 4.20 Section 1.2)
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1140
In eMMC HS400 switch sequence flow eMMC driver attempted
to execute SEND_STATUS just after switching bus timing to high
speed and before downgrading clock frequency to 52MHz. Since link
was at that time in incorrect state SEND_STATUS was failing which
made driver think switch to HS400 failed.
This change makes driver always change clock frequency after
switching bus timing and before executing SEND_STATUS.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Albecki Mateusz <mateusz.albecki@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1505
When a device under PPB contains option ROM but doesn't require 32bit
MMIO, ProgrameUpstreamBridgeForRom() cannot correctly restore the
PPB MEM32 RANGE BAR. It causes the 32bit MMIO conflict which may
cause system hangs in boot.
The root cause is when ProgrameUpstreamBridgeForRom() calls
ProgramPpbApperture() to restore the PPB MEM32 RANGE BAR, the
ProgramPpbApperture() skips to program the BAR when the resource
length is 0.
This patch fixes this issue by not calling ProgramPpbApperture().
Instead, it directly programs the PPB MEM32 RANGE BAR.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Per PCI Spec, the option ROM BAR is 32bit so the maximum option ROM
size can be hold by UINT32 type.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1408
According to the information of the above BZ-1408 and other platform
owners, NVM Express devices are becoming more likely to be a critical
part during the boot process.
This commit will add the calls to 'REPORT_STATUS_CODE' when there is a
failure happens during the NVM Express controller/device initialization
process.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bret Barkelew <brbarkel@microsoft.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1441
This commit will update the file-level comments within the SdMmcPciHcDxe
to reflect the latest specification compliance status of the driver.
Cc: Ray Ni <ray.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1422
if (Attributes) {
if ((Attributes & (~(DEV_SUPPORTED_ATTRIBUTES))) != 0) {
return EFI_UNSUPPORTED;
}
}
In above code block,
"If ((Attributes & (~(DEV_SUPPORTED_ATTRIBUTES))) != 0)" is TRUE,
the Attributes must be not 0. So we can remove the redundant
check "if (Attributes)".
Cc: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1425
This commit will resolve the VS2015 IA32 NOOPT build failure within
SdMmcPciHcDxe.
More specifically, this commit will use BaseLib API RShiftU64() to perform
right-shift operations for UINT64 type operators.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Bi Dandan <dandan.bi@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Add SDMA, ADMA2 and 26b data length support.
If V4 64 bit address mode is supported in capabilities register,
program controller to enable V4 host mode and use appropriate
SDMA registers supporting 64 bit addresses.
If V4 64 bit address mode is supported in capabilities register,
program controller to enable V4 host mode and use appropriate
ADMA descriptors supporting 64 bit addresses.
If host controller version is above V4.0, enable ADMA2 with 26b data
length support for better performance. HC 2 register is configured to
use 26 bit data lengths and ADMA2 descriptors are configured appropriately.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1359
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1394
When there is no PCI option ROM exists, today's logic still creates
virtual BAR for option ROM using Length = 0, Alignment = (-1).
It causes the final MEM32 alignment requirement is as big as
0xFFFFFFFF_FFFFFFFF.
The patch fixes this issue by only creating virtual BAR for option
ROM when there is PCI option ROM.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chiu Chasel <chasel.chiu@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Chasel Chiu <chasel.chiu@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
UEFI SCT crashed and failed in NonDiscoverablePciDeviceDxe becase
required checks were not performed. Perform parameters validation in
NonDiscoverablePciDeviceDxe.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel at linaro.org>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1376
Today's implementation reuses the 32bit MMIO resource requested by
all PCI devices MMIO BARs when shadowing the option ROM.
Take a simple example, a system has only one PCI device. It requires
8MB 32bit MMIO and contains a 4MB option ROM. Today's implementation
only requests 8MB (max of 4M and 8M) 32bit MMIO from
PciHostBridgeResourceAllocation protocol. Let's assume the MMIO range
[3GB, 3GB+8MB) is allocated. The 3GB base address is firstly
programmed to the option ROM BAR for option ROM shadow. Then the
option ROM decoding is turned off and 3GB base address is programmed
to the 32bit MMIO BAR.
It doesn't cause issues when the device doesn't request too much
MMIO.
But when the device contains a 64bit MMIO BAR which requests 4GB MMIO
and a 4MB option ROM. Let's assume [3GB, 3GB+8MB) 32bit MMIO range is
allocated for the option ROM. When the option ROM is being shadowed,
64bit MMIO BAR is programmed to value 0, which means [0, 4GB) MMIO is
given to the 64bit BAR.
The range overlaps with the option ROM range which may cause the
device malfunction (e.g.: option ROM cannot be read out) when the
device has two separate decoders: one for MMIO BAR, the other for
option ROM.
The patch requests dedicated MEM32 resource for Option ROMs and
moves the Option ROM shadow logic after all MMIO BARs are programmed.
The MMIO BAR setting to 0 when shadowing Option ROM is also skipped
because the MMIO BAR already contains the correct value.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Some SdMmc host controllers are run by clocks with different
frequency than it is reflected in Capabilities Register 1.
It is allowed by SDHCI specification ver. 4.2 - if BaseClkFreq
field value of the Capability Register 1 is zero, the clock
frequency must be obtained via another method.
Because the bitfield is only 8 bits wide, a maximum value
that could be obtained from hardware is 255MHz.
In case the actual frequency exceeds 255MHz, the 8-bit BaseClkFreq
member of SD_MMC_HC_SLOT_CAP structure occurs to be not sufficient
to be used for setting the clock speed in SdMmcHcClockSupply
function.
This patch adds new UINT32 array ('BaseClkFreq[]') to
SD_MMC_HC_PRIVATE_DATA structure for specifying
the input clock speed for each slot of the host controller.
All routines that are used for clock configuration are
updated accordingly.
This patch also adds new IN OUT BaseClockFreq field
in the Capability callback of the SdMmcOverride,
protocol which allows to update BaseClkFreq value.
The patch reuses original commit from edk2-platforms:
20f6f144d3a8 ("Marvell/Drivers: XenonDxe: Allow overriding base clock
frequency")
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Some SD Host Controlers need to do additional operations after clock
frequency switch.
This patch add new callback type to NotifyPhase of the SdMmcOverride
protocol. It is called after SdMmcHcClockSupply.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Some SD Host Controllers use different values in Host Control 2 Register
to select UHS Mode. This patch adds a new UhsSignaling type routine to
the NotifyPhase of the SdMmcOverride protocol.
UHS signaling configuration is moved to a common, default routine
(SdMmcHcUhsSignaling). After it is executed, the protocol producer
can override the values if needed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
In order to ensure bigger flexibility in the NotifyPhase
routine of the SdMmcOverride protocol, enable using an
optional phase-specific data. This will allow to exchange
more information between the protocol producer driver
and SdMmcPciHcDxe in the newly added callbacks.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1142
The fix is similar to commit ebb6c7633b.
We found that a similar fix should be applied to the NVMe PEI driver as
well. Hence, this one is for the PEI counterpart driver.
According to the the NVM Express spec Revision 1.1, for some commands
(like Get/Set Feature Command, Figure 89 & 90 of the spec), the Memory
Buffer maybe optional although the command opcode indicates there is a
data transfer between host & controller (Get/Set Feature Command, Figure
38 of the spec).
Hence, this commit refine the checks for the 'TransferLength' and
'TransferBuffer' field of the
EDKII_PEI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET structure to address this
issue.
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <Jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
There is concern at the thread
https://lists.01.org/pipermail/edk2-devel/2018-November/031951.html.
And the time point is a little sensitive as it is near edk2-stable201811.
This reverts commit 7779209971.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
There is concern at the thread
https://lists.01.org/pipermail/edk2-devel/2018-November/031951.html.
And the time point is a little sensitive as it is near edk2-stable201811.
This reverts commit 0cd6452503.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1274
In current code, EhcMonitorAsyncRequests (timer handler) will do
unmap and map operations for AsyncIntTransfers to "Flush data from
PCI controller specific address to mapped system memory address".
EhcMonitorAsyncRequests
EhcFlushAsyncIntMap
PciIo->Unmap
IoMmu->SetAttribute
PciIo->Map
IoMmu->SetAttribute
This may impact the boot performance.
Since the data buffer for EhcMonitorAsyncRequests is internal
buffer, we can allocate common buffer by PciIo->AllocateBuffer
and map the buffer with EfiPciIoOperationBusMasterCommonBuffer,
then the unmap and map operations can be removed.
///
/// Provides both read and write access to system memory by
/// both the processor and a bus master. The buffer is coherent
/// from both the processor's and the bus master's point of view.
///
EfiPciIoOperationBusMasterCommonBuffer,
Test done:
USB KB works normally.
USB disk read/write works normally.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
V3:
Call XhcFreeUrb after XhcCreateTransferTrb fails in XhcCreateTrb.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1274
In current code, XhcMonitorAsyncRequests (timer handler) will do
unmap and map operations for AsyncIntTransfers to "Flush data from
PCI controller specific address to mapped system memory address".
XhcMonitorAsyncRequests
XhcFlushAsyncIntMap
PciIo->Unmap
IoMmu->SetAttribute
PciIo->Map
IoMmu->SetAttribute
This may impact the boot performance.
Since the data buffer for XhcMonitorAsyncRequests is internal
buffer, we can allocate common buffer by PciIo->AllocateBuffer
and map the buffer with EfiPciIoOperationBusMasterCommonBuffer,
then the unmap and map operations can be removed.
///
/// Provides both read and write access to system memory by
/// both the processor and a bus master. The buffer is coherent
/// from both the processor's and the bus master's point of view.
///
EfiPciIoOperationBusMasterCommonBuffer,
Test done:
USB KB works normally.
USB disk read/write works normally.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
V3:
Match function parameter name and description between
EhciSched.c and EhciSched.h.
V2:
Add the missing "gBS->FreePool (Data);".
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1274
Extract new EhciInsertAsyncIntTransfer function from
EhcAsyncInterruptTransfer.
It is code preparation for following patch,
no essential functional change.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
V3:
Match function parameter name and description between
XhciSched.c and XhciSched.h.
V2:
Add the missing "FreePool (Data);".
Remove the unnecessary indentation change.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1274
Extract new XhciInsertAsyncIntTransfer function from
XhcAsyncInterruptTransfer.
It is code preparation for following patch,
no essential functional change.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1260
For the PassThru() service of NVM Express Pass Through Protocol, the
current implementation (function NvmExpressPassThru()) will only use the
IO Completion/Submission queues created internally by this driver during
the controller initialization process. Any other IO queues created will
not be consumed.
So the value is little to accept external IO Completion/Submission queue
creation request. This commit will refine the behavior of function
NvmExpressPassThru(), it will only accept driver internal IO queue
creation commands and will return "EFI_UNSUPPORTED" for external ones.
Cc: Jiewen Yao <Jiewen.yao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1259
According to the the NVM Express spec Revision 1.1, for some commands,
command-related information will be stored in the Dword 0 of the
completion queue entry.
One case is for the Get Features Command (Section 5.9.2 of the spec),
Dword 0 of the completion queue entry may contain feature information.
Hence, this commit will always copy the content of completion queue entry
to the PassThru packet regardless of the execution result of the command.
Cc: Liangcheng Tang <liangcheng.tang@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1142
According to the the NVM Express spec Revision 1.1, for some commands
(like Get/Set Feature Command, Figure 89 & 90 of the spec), the Memory
Buffer maybe optional although the command opcode indicates there is a
data transfer between host & controller (Get/Set Feature Command, Figure
38 of the spec).
Hence, this commit refine the checks for the 'TransferLength' and
'TransferBuffer' field of the EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET
structure to address this issue.
Cc: Liangcheng Tang <liangcheng.tang@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1267
The value 5 Port Speed field of PORTSC is new defined in
XHCI 1.1 spec November 2017.
This patch updates XhciDxe and XhciPei to handle it, otherwise
the USB 3.1 device may not be recognized with the XHCI controller
following XHCI 1.1 spec November 2017.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Current hard code Usb2Hc.XXXRevision may be not accurate.
This patch updates code to assign Usb2Hc.XXXRevision based on
SBRN (Serial Bus Release Number, PCI configuration space offset
0x60) although there is no code consuming them.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Clock control is similar in SDHCI versions greater then version 2. Add
support for more recent versions of the controller specification.
SD card support for 1.8V is also present in controller versions 3 and
greater.
https://bugzilla.tianocore.org/show_bug.cgi?id=1233
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Add SDHCI controller defines, this is useful as the version in the
register does not explictly map to a specification version. For example
vesion 4.10 of the specification is version 0x04.
https://bugzilla.tianocore.org/show_bug.cgi?id=1233
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Currently, the implementation of EFI_PCI_IO_PROTOCOL::GetLocation()
in NonDiscoverablePciDeviceDxe returns the same set of dummy values
for each instance of the NON_DISCOVERABLE_DEVICE protocol that it
attaches itself to. However, this turns out to be causing problems
in cases where software (such as the ARM Compliance Test Suite [ACS])
attempts to use these values to uniquely identify controllers, since
the collisions create ambiguity in this regard.
So let's modify GetLocation() to return an arbitrary bus/device tuple
on segment 0xff instead. This is guaranteed not to clash with other
non-discoverable PCI devices, and highly unlikely to clash with real
PCIe devices.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The change doesn't have functionality impact.
It just renames the mIoMmuProtocol to mIoMmu and moves the
declaration from PciRootBridgeIo.c to PciHostBridge.h.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Suggested-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1196
RootBridgeIoCheckParameter() verifies that the requested MMIO access
can fit in any of the MEM/PMEM 32/64 ranges. But today's logic
somehow only checks the requested access against MEM 32/64 ranges.
It should also check the requested access against PMEM 32/64 ranges.
The patch fixes this issue.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1182
Some devices can be non removable (such as eMMC) and checking
Present State Register on host controller may falsely return
an information that device is not present. Execute this
check conditionally on the SloType field value.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1185
SdMmcHcReset used to set all bits of Software Reset Register to 1
including reserved ones, which on some controllers may result in
timeout.
Now only first bit is set, which means "Software Reset for All".
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1167
When the HSEE in the USBCMD bit is a ‘1’ and the HSE bit in the
USBSTS register is a ‘1’, the xHC shall assert out-of-band error
signaling to the host and assert the SERR# pin.
To prevent masking any potential issues with SERR, this patch is
to set USBCMD Host System Error Enable(HSEE) Bit if PCICMD SERR#
Enable Bit is set.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Fei1 Wang <fei1.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The EhcReset(), EhcGetRootHubPortStatus() and EhcDriverBindingStart()
functions need to see whether the host controller (or a specific port on
the host controller) can be accessed, dependent on the controller having
(or the specific port being) an in-use debug port. Because the condition
isn't simple, extract it to a separate function.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Suggested-by: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Removing rules for Ipf sources file:
* Remove the source file which path with "ipf" and also listed in
[Sources.IPF] section of INF file.
* Remove the source file which listed in [Components.IPF] section
of DSC file and not listed in any other [Components] section.
* Remove the embedded Ipf code for MDE_CPU_IPF.
Removing rules for Inf file:
* Remove IPF from VALID_ARCHITECTURES comments.
* Remove DXE_SAL_DRIVER from LIBRARY_CLASS in [Defines] section.
* Remove the INF which only listed in [Components.IPF] section in DSC.
* Remove statements from [BuildOptions] that provide IPF specific flags.
* Remove any IPF sepcific sections.
Removing rules for Dec file:
* Remove [Includes.IPF] section from Dec.
Removing rules for Dsc file:
* Remove IPF from SUPPORTED_ARCHITECTURES in [Defines] section of DSC.
* Remove any IPF specific sections.
* Remove statements from [BuildOptions] that provide IPF specific flags.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Commit 09943f5ecc ("MdeModulePkg: Skip to manage usb debug port in EDKII
EHCI driver if it's used by usb debug port driver", 2012-04-28) made the
host controller reset in EhcDriverBindingStart() conditional. The intent
was to avoid the reset when
- one of the USB ports on the host controller was a Debug Port, AND
- the Debug Port was in use.
This translates to the following positive condition: reset the controller
only if:
- no USB port on the host controller is a Debug Port, OR
- the Debug Port is not in use.
Commit 09943f5ecc failed to implement the first subcondition, and thus
the result is too strict now (for resetting the host controller). Relax it
to the correct condition.
This issue was found by Steven Shi on QEMU. QEMU's EHCI device model does
not have a Debug Port. In repeated disconnect / connect cycles, the
controller is never reset in EhcDriverBindingStart(), therefore the
devices on the controller are never re-enumerated after a disconnect.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Steven Shi <steven.shi@intel.com>
Reported-by: Steven Shi <steven.shi@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1129
Fixes: 09943f5ecc
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Tested-by: Steven Shi <steven.shi@intel.com>
The function UsbHcUnlinkMemBlock that is never called
and its related comments have been removed.
It is missed in the patch series according to the log in
https://bugzilla.tianocore.org/show_bug.cgi?id=1062
v2:Update the title.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: shenglei <shenglei.zhang@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1109
Today's restriction of VGA device is to have only one VGA device
enabled per PCI segment. It's not correct because several segments
may share one IO / MMIO address space.
We should restrict to have one VGA per Host Bridge because each
Host Bridge has its only IO / MMIO address space.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1109
The patch doesn't change any behavior of this function.
It just renames the function to LocateVgaDevice() and renames
some parameters and local variables.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The functions that are never called have been removed.
They are XhcPeiReadDoorBellReg and UsbHcUnlinkMemBlock.
https://bugzilla.tianocore.org/show_bug.cgi?id=1062
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: shenglei <shenglei.zhang@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The functions that are never called have been removed.
They are XhcReadDoorBellReg and XhcWriteOpReg16.
https://bugzilla.tianocore.org/show_bug.cgi?id=1062
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: shenglei <shenglei.zhang@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The functions that are never called have been removed.
They are IoMmuFreeBuffer,DelinkMemoryBlock,IsMemoryBlockEmptied
,IsTDLinkPtrQHOrTD,GetCurrentFrameNumber,GetQHHorizontalLinkPtr
and GetQHHorizontalValidorInvalid.
https://bugzilla.tianocore.org/show_bug.cgi?id=1062
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: shenglei <shenglei.zhang@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Luo, Heng
Michael D Kinney
Jon Hunter
Patrick Henz
Jeff Brasen
Michael Kubacki
Laszlo Ersek
Gaurav Jain
Albecki, Mateusz
Hao A Wu
GuoMinJ
Sean Brogan
Jiewen Yao
Shenglei Zhang
Maggie Chu
Ashish Singhal
Javeed, Ashraf
xuwei6
Zhichao Gao
Ard Biesheuvel
Edgar Handal
Albecki, Mateusz
Ray Ni
Dandan Bi
Ruiyu Ni
Vladimir Olovyannikov
Marcin Wojtas
Tomasz Michalec
Star Zeng
Chen A Chen