Update XHCI driver to consume IOMMU_PPI to allocate DMA buffer.
If no IOMMU_PPI exists, this driver still calls PEI service
to allocate DMA buffer, with assumption that DRAM==DMA.
This is a compatible change.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=653
Correct description of Timeout param in XhciReg.h to be matched with
XhciReg.c.
Cc: Alexei Fedorov <Alexei.Fedorov@arm.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
We found there are loops of *2* Maps and only *1* Unmap and
the DMA buffer address is decreasing.
It is caused by the below code flow.
XhcAsyncInterruptTransfer ->
XhcCreateUrb ->
XhcCreateTransferTrb ->
Map Urb->DataMap (1)
Timer: loops of *2* Maps and only *1* Unmap
XhcMonitorAsyncRequests ->
XhcFlushAsyncIntMap ->
Unmap and Map Urb->DataMap (2)
XhcUpdateAsyncRequest ->
XhcCreateTransferTrb ->
Map Urb->DataMap (3)
This patch is to eliminate (3).
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Per NVM Express Spec, software should notify NVME HW when shutdown
occurs.
The NVME controller requires notification for shutdown as part of
its management of internal structures. Even with FUA, failing to
notify the NVME controller to shutdown power off causes the NVME
controller to take quite some time to organize its tables on the
next power on. This time exceeds the normal timeout, so we would
fail to boot the NVME disk.
The host should set the Shutdown Notification (CC.SHN) field to 01b
to indicate a normal shutdown operation. The controller indicates
when shutdown processing is completed by updating the Shutdown Status
(CSTS.SHST) field to 10b.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
PciScanBus() assumes the GetResourcePadding() puts BUS descriptor
in the very beginning, if it's not, the Descriptors will be updated
to point to middle of the pool buffer, which can cause
FreePool(Descriptors) hang in DEBUG image.
No functionality impact to RELEASE image.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=644
According to XHCI spec:
4.10.2.1 Stall Error
4.10.2.4 Babble Detected Error
When a device transmits more data on the USB than the host controller
is expecting for a transaction, it is defined to be babbling.
In general, this is called a Babble Error. When a device sends more
data than the TD Transfer Size bytes (TD Babble), unexpected activity
that persists beyond a specified point in a (micro)frame (Frame Babble),
or a packet greater than Max Packet Size (Packet Babble), the host
controller shall set the Babble Detected Error in the Completion Code
field of the TRB, generate an Error Event, and halt the endpoint
(refer to Section 4.10.2.1).
This patch is to also check for EFI_USB_ERR_BABBLE error returned as
a TransferResult and then proceed to XhcRecoverhaltedEndPoint.
Cc: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=433
When a blocking NVMe PassThru request experiences timeout, the current
codes in function NvmExpressPassThru() do not abort the timeout request
while advancing synchronous Submission Queue tail. Therefore, it is
possible to submit a new blocking PassThru request when the synchronous
Submission Queue is full.
The commit adds logic to abort the timeout request by resetting the NVMe
controller when a timeout occurs for a blocking PassThru request.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This fixes BULK data loss when transfer is detected as timeout but
finished just before stopping endpoint.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
The patch separates the common logic in XhcControlTransfer,
XhcBulkTransfer and XhcSyncIntTransfer to a sub-routine
XhcTransfer. It doesn't have functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Current implementation of IsTransferRingTrb only checks whether
the TRB is in the RING of the URB.
The patch enhanced the logic to check that whether the TRB belongs
to the transaction of URB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Some USB devices don't report data periodically through Int
Transfer. They report data only when be asked. If the TRB
is not removed from the XHCI HW, when next time HOST asks
data again, the data is reported but consumed by the previous
TRB, which results the HOST thinks data never comes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=510
The commit fills the 'Interval' field of the Endpoint Context data for
isochronous endpoints. It will resolve the error when a Configure
Endpoint Command is sent to an isochronous endpoint.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
If IOMMU protocol is installed, PciBus need call IOMMU
to set access attribute for the PCI device in Map/Ummap.
Only after the access attribute is set, the PCI device can
access the DMA memory.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Previous patch Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Previous patch Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
If IOMMU protocol is installed, PciHostBridge just calls
IOMMU AllocateBuffer/FreeBuffer/Map/Unmap.
PciHostBridge does not set IOMMU access attribute,
because it does not know which device request the DMA.
This work is done by PciBus driver.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Previous patch Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Previous patch Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
In function UfsHcDriverBindingStart(), the return value 'Status' may be
overridden during the original PCI attributes restore process.
This commit refines the logic to avoid such override.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit removes the unused field 'EFI_HANDLE Handle' in Ufs host
controller private data structure 'UFS_HOST_CONTROLLER_PRIVATE_DATA'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In case of an async command if updating the submission queue tail
doorbell fails then the command will not be picked up by device and
no completion response will be created. This scenario has to be handled.
Also if we create an AsyncRequest element and insert in the async queue,
it will never receive a completion so in the timer routine this element
won't be freed, resulting in memory leak. Also in case of blocking calls
we should capture the status of updating completion queue head doorbell
register and return it to caller of PassThru.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Suman Prakash <suman.p@samsung.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
In function ReadCapacity(), the following expression:
MediaInfo->LastBlock = (Data.LastLba3 << 24) |
(Data.LastLba2 << 16) |
(Data.LastLba1 << 8) |
Data.LastLba0;
(There is also a similar case in this function.)
will involve undefined behavior in signed left shift operations.
Since Data.LastLbaX is of type UINT8, and MediaInfo->LastBlock is of type
UINTN. Therefore, Data.LastLbaX will be promoted to int (32 bits, signed)
first, and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Data.LastLba3 is 1, (Data.LastLba3 << 24) will be out of
the range within int type. The undefined behavior of the signed left shift
will lead to a potential of setting the high 32 bits of
MediaInfo->LastBlock to 1 during the cast from type int to type UINT64
for X64 builds.
This commit will add an explicit UINT32 type cast for Data.LastLba3 to
resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
For async commands, the buffer allocated for Prp list is
not getting freed, which will cause memory leak for async
read write command. For example testing async command flow
with custom application to send multiple read write commands
were resulting in decrease of available memory page in memmap,
which eventually resulted in system hang. Hence freeing
AsyncRequest->MapData, AsyncRequest->MapMeta, AsyncRequest->MapPrpList and
AsyncRequest->PrpListHost when async command is completed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Suman Prakash <suman.p@samsung.com.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
At worst case, OCR register may always not set BIT31. It will cause
original code enter to dead loop. Adding a break for such case.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
There are cases that the operands of an expression are all with rank less
than UINT64/INT64 and the result of the expression is explicitly cast to
UINT64/INT64 to fit the target size.
An example will be:
UINT32 a,b;
// a and b can be any unsigned int type with rank less than UINT64, like
// UINT8, UINT16, etc.
UINT64 c;
c = (UINT64) (a + b);
Some static code checkers may warn that the expression result might
overflow within the rank of "int" (integer promotions) and the result is
then cast to a bigger size.
The commit refines codes by the following rules:
1). When the expression is possible to overflow the range of unsigned int/
int:
c = (UINT64)a + b;
2). When the expression will not overflow within the rank of "int", remove
the explicit type casts:
c = a + b;
3). When the expression will be cast to pointer of possible greater size:
UINT32 a,b;
VOID *c;
c = (VOID *)(UINTN)(a + b); --> c = (VOID *)((UINTN)a + b);
4). When one side of a comparison expression contains only operands with
rank less than UINT32:
UINT8 a;
UINT16 b;
UINTN c;
if ((UINTN)(a + b) > c) {...} --> if (((UINT32)a + b) > c) {...}
For rule 4), if we remove the 'UINTN' type cast like:
if (a + b > c) {...}
The VS compiler will complain with warning C4018 (signed/unsigned
mismatch, level 3 warning) due to promoting 'a + b' to type 'int'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
For pointer subtraction, the result is of type "ptrdiff_t". According to
the C11 standard (Committee Draft - April 12, 2011):
"When two pointers are subtracted, both shall point to elements of the
same array object, or one past the last element of the array object; the
result is the difference of the subscripts of the two array elements. The
size of the result is implementation-defined, and its type (a signed
integer type) is ptrdiff_t defined in the <stddef.h> header. If the result
is not representable in an object of that type, the behavior is
undefined."
In our codes, there are cases that the pointer subtraction is not
performed by pointers to elements of the same array object. This might
lead to potential issues, since the behavior is undefined according to C11
standard.
Also, since the size of type "ptrdiff_t" is implementation-defined. Some
static code checkers may warn that the pointer subtraction might underflow
first and then being cast to a bigger size. For example:
UINT8 *Ptr1, *Ptr2;
UINTN PtrDiff;
...
PtrDiff = (UINTN) (Ptr1 - Ptr2);
The commit will refine the pointer subtraction expressions by casting each
pointer to UINTN first and then perform the subtraction:
PtrDiff = (UINTN) Ptr1 - (UINTN) Ptr2;
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Compiler calculates the PciBar[BarIndex] using
sizeof (PciBar[0]) * BarIndex, when BarIndex is type of UINT64,
the above calculation generates assembly code using _allmul.
Change BarIndex to UINTN to avoid the build failure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
When the VendorId/DeviceId/RevisionId/SubsystemVendorId
/SubsystemDeviceId is MAX_UINTN, IncompatiblePciDeviceSupport
driver doesn't use it to match any IDs.
The patch fixes this bug.
Since PciBus driver always calls IncompatiblePciDeviceSupport
using IDs read from HW, MAX_UINTN is never passed to this
driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The patch replaces the following macros:
DEVICE_ID_NOCARE (0xFF) --> MAX_UINT64
PCI_ACPI_UNUSED (0) --> 0
PCI_BAR_ALL (0xFF) --> MAX_UINT64
PCI_BAR_NOCHANGE (0) --> 0
PCI_BAR_EVEN_ALIGN --> EVEN_ALIGN (local definition)
Since the PciBus driver was updated to accept Spec defined values
in previous commit, the above replacements don't impact
functionality.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
PI spec IncompatiblePciSupport part defines (UINT64)-1 as all BARs
and 0 to use existing alignment. PciBus driver didn't accept these
values. It treated 0xFF as all BARs and 0xFFFFFFFFFFFFFFFFULL to use
existing alignment.
The patch changes the code to still accept old values while also
accept values defined in PI spec. So that the driver can provide
backward compatibility and follow spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When BarIndex equals to 0xFF, default value 0 is used as the BAR
index. Though PCI_BAR_ALL and MAX_UINT8 shares the same value,
using PCI_BAR_ALL is like to match any BAR not BAR 0, it's more
proper to use MAX_UINT8 here.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If the code eventually returns "Status" anyway, it does not make
sense to explicitly return "Status" in case of an error, too.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Refine the codes to compare the definition 'SIZE_4GB' with type
EFI_PHYSICAL_ADDRESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Add support for non-coherent DMA, either by performing explicit cache
maintenance when DMA mappings are aligned to the CPU's DMA buffer alignment,
or by bounce buffering via uncached mappings otherwise.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Fix switch/case statement type mismatch in functions PciIoMemRead &
PciIoMemWrite.
Parameter 'Width' is of enum type EFI_PCI_IO_PROTOCOL_WIDTH, but the enum
type provided in 'switch (Width)' block is of type
EFI_PCI_ROOT_BRIDGE_IO_PROTOCOL_WIDTH.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Add missing EFIAPI modifiers to the functions that are exposed via the
PCI I/O protocol.
At the same time, add a missing UINT8 cast which breaks the build on
Visual Studio.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
This implements support for non-discoverable PCI compatible devices, i.e,
devices that are not on a PCI bus but that can be controlled by generic PCI
drivers in EDK2.
This is implemented as a UEFI driver, which means we take full advantage
of the UEFI driver model, and only instantiate those devices that are
necessary for booting.
Care is taken to deal with DMA addressing limitations: DMA mappings and
allocations are moved below 4 GB if the PCI driver has not informed us
that the device being driven is 64-bit DMA capable. DMA is implemented as
coherent, support for non-coherent DMA is implemented by a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Port status bits are clear in original code, so no enumeration
takes place.
Changing this to prevent the status bits from being cleared
allows enumeration to proceed normally.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Mike Turner <Michael.Turner@microsoft.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mike Turner <Michael.Turner@microsoft.com>
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit e27cca has a typo on DEBUG level macro. And this debug
message should be DEBUG_INFO rather than DEBUG_ERROR.
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
reviewed-by: Marcin Wojtas <mw@semihalf.com>
EFI_D_INFO, EFI_D_VERBOSE, EFI_D_WARN and EFI_D_ERROR are replaced
with currently recommended values.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
We send ADDRESS DEVICE CMD in XhcInitializeDeviceSlot(), which will
cause XHC issue a USB SET_ADDRESS request to the USB Device.
According to USB spec, there should have a 10ms delay before this
operation after resetting a given port.
But in original code, there is a possible path which may have no such
10ms delay:
UsbHubResetPort()->UsbHubSetPortFeature()->Stall(20)->UsbHubGetPortSt
atus()->XhcPollPortStatusChange()->(if RESET_C bit is set)->
XhcInitializeDeviceSlot()->(if RESET_C bit is set)->Stall(10)
So this patch is used to fix above issue.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Tested-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When PciSioSerial is firstly started with a non-NULL remaining
device path, the UART instance is created using the parameters
specified in the remaining device path. Later when the driver
is started again on the same UART controller with NULL remaining
device path, the correct logic is to directly return SUCCESS
instead of current buggy implementation which wrongly produces
another UART using the default parameters.
The bug causes two UARTs are created when the UART is configured
in 57600 baud rate.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Short Packet case is a normal case, we shouldn't print it as an error
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The 'universal' PCI bus driver in MdeModulePkg contains a quirk to
degrade 64-bit PCI MMIO BARs to 32-bit in the presence of an option
ROM on the same PCI controller.
This quirk is highly specific to not just the X64 architecture in general,
but to the PC platform in particular, given that only X64 platforms that
require legacy PC BIOS compatibility require it. However, making the
quirk dependent on the presence of the legacy BIOS protocol met with
resistance, due to the fact that it introduces a dependency on the
IntelFrameworkModulePkg package.
So instead, make the quirk configurable, by introducing a feature flag PCD
'PcdPciDegradeResourceForOptionRom' which defaults to TRUE only for X64.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Currently, the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute is completely
ignored by the PCI host bridge driver, which means that, on an implementation
that supports DMA above 4 GB, allocations above 4 GB may be provided to
devices that have not expressed support for it.
So in addition to checking 'RootBridge->DmaAbove4G' to establish whether the
root bridge itself supports DMA above 4 GB, we must also take into account
the operation type (EfiPciOperationBusMaster{Read|Write|CommonBuffer}64),
and the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute, when mapping and
allocating DMA memory, respectively.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Since current codes in NvmExpressDxe already support the non-blocking I/O
feature for EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL interface, the relative bit
in the 'Attributes' field of EFI_NVM_EXPRESS_PASS_THRU_MODE should be set
to reflect this.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit fixes the issue that the caller event passed to
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() will not be signaled for
NVME Admin commands.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru()
should return EFI_INVALID_PARAMETER if the input 'NamespaceId' is invalid
for the NVM Express controller. This commit adds check in PassThru() to
follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit adds serveral checks for the 'Packet' parameter passed to the
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() API:
The check for the 'TransferLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value will not
exceed the maximum data transfer size allowed by a controller.
The check for the 'TransferBuffer' and 'TransferLength' fields in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET when the Opcode of an NVME
command indicates a data transfer between controller and host.
The check for the 'MetadataLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value is not 0
when the corresponding 'MetadataBuffer' field has a non-NULL value.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to UEFI spec, an EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL with neither
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_LOGICAL nor
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_PHYSICAL set in the Attributes field
is an illegal configuration.
This commit adds this check in the PassThru API to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, the 'TransferBuffer' and 'MetadataBuffer' used
in a data transfer should be aligned on the boundary specified by the
IoAlign field in the EFI_NVM_EXPRESS_PASS_THRU_MODE structure.
This commit adds this check to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNextNamespace() should return
EFI_NOT_FOUND when the value pointed to by NamespaceId is the namespace ID
of the last namespace on the NVM Express controller. This commit modifies
the check for NamespaceId to follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNamespace() should return
EFI_NOT_FOUND when the input DevicePath is a device path node type that
the NVM Express Pass Thru driver supports, but there is not a valid
translation from DevicePath to a namespace ID. Current code will return
EFI_SUCCESS. This commit adds additional check in the GetNameSpace API to
make sure correct status is returned.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.BuildDevicePath() should return
EFI_NOT_FOUND when the input NamespaceId is not valid. However, current
code returns EFI_DEVICE_ERROR instead. This commit modifies the check for
input NamespaceId to return the correct status.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The gBS->OpenProtocol() calls to open EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL
in NvmExpress.c will crash the data in 'Mode' field of
'Private->Passthru'.
The third parameter of gBS->OpenProtocol() is an output parameter that
stores the address where a pointer to the corresponding Protocol
Interface. The current code mistakenly pass '&Private->Passthru' (a
pointer of the EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL) as the third
parameter. This will crash the data in 'Mode' filed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The last TRB in transfer ring is a LINK type TRB, which shouldn't
be accounted as a valid item in IsAsyncIntTrb().
Without this fix, the original algo will bring issue on those URBs
whose TRBs crosses the transfer ring.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
> cc1: warnings being treated as errors
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:
> In function 'GetProposedResources':
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:1388:
> error: integer constant is too large for 'long' type
Append a ULL suffix to the replacement text of PCI_RESOURCE_LESS that is
aligned with the style of the EFI_RESOURCE_SATISFIED and
EFI_RESOURCE_NOT_SATISFIED macros.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Section 7.8.2 of the PCI Express specification (r4.0 v0.3), entitled "PCI
Express Capabilities Register (Offset 02h)", and section 7.8.9 "Slot
Capabilities Register (Offset 14h)" of the same, describe the conditions
when a PCIe port should be considered "supporting hotplug":
- it should be a root complex port or a switch downstream port, and
- it should have the "Slot Implemented" bit set in the Express
Capabilities Register, and
- it should have the "Hot-Plug Capable" bit set in the Slot Capabilities
Register.
The first two sub-conditions are already implemented in at least two open
source projects I could find:
- in SeaBIOS by Marcel Apfelbaum: "hw/pci: reserve IO and mem for pci
express downstream ports with no devices attached"
<https://code.coreboot.org/p/seabios/source/commit/3aa31d7d6375>,
- in edk2 itself, in the implementation of the "PCI" UEFI Shell command:
see the "PcieExplainTypeSlot" case label in function
PciExplainPciExpress(), file
"ShellPkg/Library/UefiShellDebug1CommandsLib/Pci.c".
PciBusDxe recognizes such PCIe ports as bridges, but it doesn't realize
they support hotplug. In turn PciBusDxe omits getting any resource padding
information from the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL for these
bridges:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Implement a function called SupportsPcieHotplug() for identifying such
ports, and call it from IsPciHotPlugBus() (after the call to IsSHPC()).
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
The PCI Hot Plug capability register block is marked with capability ID
0x0C (EFI_PCI_CAPABILITY_ID_SHPC), not 0x06
(EFI_PCI_CAPABILITY_ID_HOTPLUG).
This bug prevents PciBusDxe from recognizing whether a PCI-to-PCI bridge
supports hotplug. In turn the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL is
not consulted for resource padding information:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
IsSHPC() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Look for the correct capability ID.
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
- abstrated to abstracted
- accessibla to accessible
- addres to address
- apropriate to appropriate
- arry to array
- availabe to available
- avaliable to available
- becasue to because
- correponding to corresponding
- etablished to established
- exeuction to execution
- extensiable to extensible
- fileds to fields
- loadding to loading
- ptototypes to prototypes
- prococol protocol
- requried to required
- resoruce to resource
- runing to running
- uild to build
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
We have to upgrade the TPL level used by SdMmc stack because the
following flow:
DiskIo2ReadWriteDisk() in logical partition -> PartitionReadBlocksEx()
in logical partition at TPL callback level -> ProbeMediaStatusEx()
with sync request -> DiskIo2ReadWriteDisk() in physical partition ->
waiting for async task completion.
if the low layer driver doesn't run at TPL_NOTIFY level, it will have
no time to trigger async task and cause system hang.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
This delay is necessary for eMMC reset to working properly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joe Zhou <shjzhou@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The Maximum Queue Entries Supported (MQES) field in the CAP (Controller
Capabilities) register for a NVMe controller restrict the maximum
individual queue size that the controller supports.
The origin code does not check this value and always uses a hardcode value
when creating I/O submission/completion queues for asynchronous
transmission. The hardcode value might be larger than the MQES field, this
will lead to an 'Invalid Queue Size' error when creating I/O
submission/completion queues.
The patch will add checks to make sure proper queue size is passed when
creating I/O submission/completion queues.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Move NvmExpressHci.h definitions to a public industry standard
header in MdePkg. The NvmExpressHci.h contains definitions based
on the NVMe v1.1 specification. These definitions should be in
a public header so that clients of the NVMe passthru protocol
can use them to execute NVMe commands.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Darbin Reyes <darbin.emm.reyes@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The driver entry point calls gDS->SetMemorySpaceAttributes().
This interface may return EFI_NOT_AVAILABLE_YET when CPU Arch
protocol is not available.
So we need to list CpuArch protocol in its INF dependency section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
PciBus driver originally always degrade (64->32) the MMIO resource
for PCI BAR when the PCI device contains option ROM.
But the degrade causes the PCI device can only use resource below 4GB
which makes the resource allocation fails when the PCI device wants
very big MMIO.
The patch follows the PI spec (ECR 1529) to honor the granularity
setting for PCI BAR from IncompatiblePciDeviceSupport so that even
for PCI device which contains option ROM, the degrade doesn't happen
if IncompatiblePciDeviceSupport returns 64 as granularity.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Remove "Efi" from gEfiIncompatiblePciDeviceSupport to shorten
the global variable name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Together with EFI_BLOCK_IO_PROTOCOL, EFI_BLOCK_IO2_PROTOCOL is also
produced on NVMe devices.
The following Block I/O 2 functions are implemented:
Reset
ReadBlocksEx
WriteBlocksEx
FlushBlocksEx
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When PcdPciDisableBusEnumeration is enabled, the PciBus driver
might get into a dead loop if the secondary bus register on PCI
bridge is not programmed or programmed improperly. Adding this
check to avoid any potential dead loop caused by this.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Lee Leahy <Leroy.p.leahy@intel.com>
Change PciHostBridgeDxe driver to not install the
PciHostBridgeResourceAllocation protocol and let
PciRootBridgeIo.Configuration() return the correct PCI resource
assignment information when the ResourceAssigned is TRUE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
When the aperture base equals to aperture limit, the old code treats
the aperture as non-existent. It's not correct because it indicates
a range starting with base and the length is 1.
The new code corrects the comparing bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The patch aligns to the IntelFrameworkModulePkg/Bus/Isa/IsaSerialDxe
driver not flush the UART in Reset() and SetAttributes() function.
It was found the flush causes hang on certain PCI serial devices.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Jin <eric.jin@intel.com>
Before switch to a bus mode, we need check if the SD device supports
this bus mode.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code is using ADMA mode to do clock tuning procedure. It
may have problem on some SD/MMC host controllers as there is no way to
know when to send next tuning cmd.
Update it to PIO mode to strictly follow SD Host Controller Simplified
Specification 3.0 Figure 2-29. By this way, if the Buffer Read Ready
interrupt is set, we could know it's ok to send the next clock tuning
cmd.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code has a bug to calculate which clock freq should be
used when the target clock freq is larger than the BaseClock Freq
provided by the system.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Check if the card is identified/initialized correctly. if not, break
the following cmd execution through PassThru()/ResetDevice().
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The "IoAlign" field in EFI_BLOCK_IO_MEDIA of an NVMe device is not
initialized properly, leading to a zero value for this field.
It should be initialized from the "IoAlign" field in the
EFI_NVM_EXPRESS_PASS_THRU_MODE structure maintained by the NVMe
controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If the current PCI configuration requires no resources to be allocated at
all (i.e., unpopulated bus), the PCI enumeration code creates a single
ACPI_ADDRESS_SPACE_DESCRIPTOR memory descriptor with all fields cleared.
This is rejected by the SubmitResources() implementation of the generic
PciHostBridgeDxe in the following way:
PciHostBridge: SubmitResources for PcieRoot(0x0)
Mem: Granularity/SpecificFlag = 0 / 00
Length/Alignment = 0x0 / 0x0
PciBus: HostBridge->SubmitResources() - Invalid Parameter
ASSERT_EFI_ERROR (Status = Invalid Parameter)
ASSERT [PciBusDxe] .../PciBusDxe/PciLib.c(561): !EFI_ERROR (Status)
So instead, create the empty configuration as a single entry of type
EFI_ACPI_END_TAG_DESCRIPTOR.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Phase Tag, SqTdbl/CqHdbl and SqBuffer/CqBuffer should be cleared in
NvmeControllerInit() to make HC functionality work when user invokes
NvmeBlockIoReset().
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
In EnumerateNvmeDevNamespace(), when Private->ControllerData->Sn and/or
Private->ControllerData->Mn are NOT null-terminated strings,
UnicodeSPrintAsciiFormat(…) may generate unexpected (garbage) output
string.
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Memory pointed to by Private->ControllerData has not been freed up
correctly at error handling path.
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
According to SD Host Controller 3.0 spec figure 3-10, we have to wait
1ms before checking DAT[3:0] in voltage switch proc
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The original code doesn't reset the slot when there is device change.
It may bring issue on device identification procedure of some SD cards.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@Intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
If there is no card presented before power on, there would
have no card change interrupt generated. This is a corner
case which can't be handled by old logic.
The patch is used to move card present detection in the front
of card change interrupt detection.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The bcdUSB value of usb3.1 is 0x0310, we update the condition judgment
to get correct max packet size for usb3.1 dev.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Set the Force Unit Access (FUA) bit in NVMe Write - Command Dword 12 to
ensure write-through behavior.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This stack includes:
1. Dxe phase support by:
1) SdMmcPciHcDxe driver to consume PciIo and produce
SdMmcPassThru.
2) SdDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2.
3) EmmcDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2/SSP.
2. Pei phase support
1) SdBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
2) EmmcBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
3) SdMmcPciHcPei driver to produce SdMmcHostController
Ppi.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Remove variables that are declared, assigned but never referenced. This
fixes a warning emitted by GCC when -Wunused-but-set-variable is in effect.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
When there is no bridge before the HPC (hot plug controller),
the issue cannot be seen.
But when there are bridges before the HPC, the PciBus will only
use the value (= <CurrentBusNumber> + <ReservedBusNumber>) as the
sub-ordinary bus number for HPC.
The correct sub-ordinary bus number should be:
<CurrentBusNumber> + <OccupiedBusNumber>(by earlier bridges) +
<ReservedBusNumber>.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Failing to set EFI_MEMORY_UC to MMIO aperture is not a fatal error.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
The "pc" ("pc-i440fx-*") machine types of QEMU don't support extended
config space. Accordingly, OVMF will use the following library instances
in connection with the core PciHostBridgeDxe driver:
BasePciSegmentLibPci [class: PciSegmentLib]
BasePciLibCf8 [class: PciLib]
BasePciCf8Lib [class: PciCf8Lib]
Add a new field to the PCI_ROOT_BRIDGE structure so that
RootBridgeIoCheckParameter() can catch config space offsets above 0xFF on
such old (emulated) platforms.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
... in preparation for the next patch.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Some platform doesn't use CPU(HOST)/Device 1:1 mapping for PCI Bus.
But PCI IO doesn't have interface to tell caller (device driver)
whether the address returned by GetBarAttributes() is HOST address
or device address.
UEFI Spec 2.6 addresses this issue by clarifying the address returned
is HOST address and caller can use AddrTranslationOffset to calculate
the device address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The patch removes the assumption that the resources claimed by root
bridges should not exist. Because resources might have been added:
1. by platform modules either in PEI through resource HOB, or in DXE,
before the PCI host bridge driver runs.
2. Resources claimed by different root bridges may overlap so that
resource adding operation for latter root bridges may fail if
we assume the resource should not exist.
In real world, this patch is to fit OVMF platform needs because
different root bridges in OVMF platform shares the same resources.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
[lersek@redhat.com: intersection-based implementation]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
These workhorse functions are part of the BlockIo protocol that
NvmExpressDxe produces. For bulk data access, they are called very
frequently. Their debug messages should be therefore downgraded to
EFI_D_VERBOSE.
In addition, the following DEBUG() warts are cleaned up:
- The function name should be printed with %a / __FUNCTION__, so that
renaming the function, or copying the DEBUG() elsewhere, be reflected in
the debug output automatically. (In fact, after this patch, the DEBUG()
calls become identical.)
- "Lba" is of type UINT64, therefore it should be printed with %Lx, not
%x.
- "OrginalBlocks" and "Blocks" are both UINTN. The only portable way to
print UINTN is to convert it to UINT64 manually, then format it with the
%Lx (or %Lu) conversion specifier.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19763 6f19259b-4bc3-4df7-8a09-765794883524
This driver links to PciHostBridgeLib provided by platform/silicon to
produce PciRootBridgeIo and PciHostBridgeResourceAllocation protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19658 6f19259b-4bc3-4df7-8a09-765794883524
Operands in a bitwise operation have different size. Update code to fix it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19309 6f19259b-4bc3-4df7-8a09-765794883524
Add missing braces in module global mControllerDevicePathTemplate.
Initialize ControllerNumber and ContainsControllerNode in
SerialControllerDriverStart() to address warning for potential use
before initialization warning.
Move initialization of local SerialIo earlier in
SerialControllerDriverStart() to address warning for potential use
before initialization warning.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19232 6f19259b-4bc3-4df7-8a09-765794883524
PciSioSerialDxe driver can manages UARTs on a SIO chip or a PCI/PCIE
card.
It manages the SIO instance whose last device path node is a ACPI
device path and the HID in the ACPI device path node equals to
EISA_PNP_ID (0x501).
It also manages the PCI IO instance whose class code is 7/0/2 (16550
UART). But when proper value is set to PcdPciSerialParameters, the
driver can also manage non-standard PCI serial cards by matching
the Vendor ID and Device ID specified in PcdPciSerialParameters.
The PCI BAR index, IO/MMIO offset, register stride, clock rate can
also be specified through the same PCD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19179 6f19259b-4bc3-4df7-8a09-765794883524
For a hot plug bridge with device attached, PciBusDxe driver reserves
the resources which equal to the total amount of padding resource
returned from HotPlug->GetResourcePadding() and the actual occupied
resource by the attached device. The behavior is incorrect.
Correct behavior is to reserve the bigger one between the padding
resource and the actual occupied resource.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18719 6f19259b-4bc3-4df7-8a09-765794883524
The resource dumping logic contains a bug which cannot dump the
resource for hot plug controller correctly. The patch fixes this
bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18718 6f19259b-4bc3-4df7-8a09-765794883524
Leif suggested to split the big patch to smaller ones.
This reverts commit 73b7f115c653c807b9d0be97bf516871d8aff7ba.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18717 6f19259b-4bc3-4df7-8a09-765794883524
Add a check for ResourcePaddingDescriptors being a valid pointer in
DumpPpbPaddingResource() to prevent looping on memory not owned by
PciBusDxe. The ResourcePaddingDescriptors is initialized to NULL
when the PCI_IO_DEVICE structure is allocated and remains NULL if
no PCI hot plug controllers are present. This issue is only
observed when DEBUG_CODE() macros are enabled and was introduced
by the following patch:
[edk2] [Patch] MdeModulePkg: Fix a PciBusDxe hot plug bug
SVN revsion 18658
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Kinney Michael <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18696 6f19259b-4bc3-4df7-8a09-765794883524
For a hot plug bridge with device attached, PciBusDxe driver reserves
the resources which equal to the total amount of padding resource
returned from HotPlug->GetResourcePadding() and the actual occupied
resource by the attached device. The behavior is incorrect.
Correct behavior is to reserve the bigger one between the padding
resource and the actual occupied resource.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18658 6f19259b-4bc3-4df7-8a09-765794883524
When looping through all PCI functions, code should not look for functions
1-7 if function 0 is not present or if function 0 indicates the device is
not multifunction. Prior to this fix the code would use stale data in a
buffer to determine if a device is multifunction even if function 0 is not
present. This fixes a code bug and provides very small performance
improvements.
PCI 2.3 Specification states: They [multifunction devices] are also
required to always implement function 0 in the device. Implementing other
functions is optional and may be assigned in any order.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joseph Shifflett <joseph.shifflett@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18574 6f19259b-4bc3-4df7-8a09-765794883524
Certain PCI device may have capability pointing to itself.
Update LocateCapabilityRegBlock() to break when detecting such loop.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18473 6f19259b-4bc3-4df7-8a09-765794883524
The error handling for timeout case is enhanced to remove TDs from
transfer ring. The original code only removed s/w URB, but the h/w
transfer descriptor TDs didn't get removed. It would cause data lost
for data stream peripheral, such as usb-to-serial device, from the
s/w perspective.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18313 6f19259b-4bc3-4df7-8a09-765794883524
In the original code, there exists some mismatches between the real
waiting time and the corresponding timeout comments. For example, the
XHC_GENERIC_TIMEOUT comment says it's 10ms timeout value, but the real
code in fact waits 10s.
So the code is refined to be consistent in code logic and comments.
Note XHC_POLL_DELAY macro also be removed and the polling interval in
XhcWaitOpRegBit() is changed from 1ms to 1us to keep same code style
with other code. It has no real functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18235 6f19259b-4bc3-4df7-8a09-765794883524
EDKII usb stack is using a TPL_CALLBACK timer to monitor async transfer
request and signal event if it's done. As usb enumeration and usb mass
storage block i/o read/write runs on TPL_CALLBACK and TPL_NOTIFY level
respectively, It blocks usb async transfer requests, usually usb mouse
/use kb, getting time to run.
Without this change, user couldn't get usb mouse/kb state in time (will
show a little lag from UI view) when there is other usb transactions, such
as a new usb device inserted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18169 6f19259b-4bc3-4df7-8a09-765794883524
According to the PCI spec, when software writes all-one to BAR for size probing,
the value read back should be 0b1...10...0 after masking the BAR type bits.
But in real world, it's possible that certain device returns 0b0...01...10...0
for MEM64 BAR size probing: some bits in the high 32bit may be 0.
PciBus driver has the code to handle such case. However, it doesn't handle the
case that the high 32bit is totally 0. The patch is to handle the special case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18114 6f19259b-4bc3-4df7-8a09-765794883524
The logic in an if statement in PciIo is too complex and hard to understand
and make VS2015 build failure. The fix simplifies the logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18109 6f19259b-4bc3-4df7-8a09-765794883524
Produce this protocol for each namespace at NVMe controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17638 6f19259b-4bc3-4df7-8a09-765794883524
Open NVM_EXPRESS_PASS_THRU rather than PCI_IO to create parent-child
relationship.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17636 6f19259b-4bc3-4df7-8a09-765794883524
The initialization of Cc.Iosqes and Cc.Iocqes should not be removed
before any I/O operation as it would impact Qemu-NVMe functionality
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17559 6f19259b-4bc3-4df7-8a09-765794883524
LocatePciExpressCapabilityRegBlock () doesn't check the return status of Pci.Read().
Certain platform's PciRootBridge.Pci.Read() doesn't support PCIE access causing the CapabilityEntry not updated.
If the uninitialized CapabilityEntry equals to a big enough initial value, the while-loop will never end.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17513 6f19259b-4bc3-4df7-8a09-765794883524
This patch produces a EFI_NVM_EXPRESS_PASS_THRU protocol instance
on device handle to provide upper user a way to send cmd to NVMe
device.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17286 6f19259b-4bc3-4df7-8a09-765794883524
It includes 4 drivers:
1. UfsPassThruDxe, which is a UEFI driver and consumes EFI_UFS_HOST_CONTROLLER_PROTOCOL and produces EFI_EXT_SCSI_PASS_THRU_PROTOCOL
2. UfsPciHcDxe, which is specific for pci-based UFS HC implementation and is a UEFI driver to produce EFI_UFS_HOST_CONTROLLER_PROTOCOL.
3. UfsBlockIoPei, which is a PEI driver and consumes EFI_UFS_HOST_CONTROLLER_PPI and produces EFI_PEI_VIRTUAL_BLOCK_IO_PPI.
4. UfsPciHcPei, which is specific for pci-based UFS HC implementation and is a PEI driver to produce EFI_UFS_HOST_CONTROLLER_PPI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17246 6f19259b-4bc3-4df7-8a09-765794883524
The number of the Prp lists and the number of the entries in last Prp list may be calculated wrongly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Baban Devkate <baban.devkate@seagate.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17208 6f19259b-4bc3-4df7-8a09-765794883524
The restriction of UsbHc2.SyncInterruptTransfer() on interrupt transfer direction is removed. This interface could support Interrupt IN/OUT now.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17041 6f19259b-4bc3-4df7-8a09-765794883524
- Fix EFI_IPv4_ADDRESS usages to use a macro to copy the structure
instead of direct assignment, to avoid runtime alignment errors.
- Fix a EFI_INPUT_KEY usage in TerminalDxe to use CopyMem() to copy the
structure instead of direct assignment, to avoid runtime alignment error.
- Delete excess local variables that are initialized but otherwise unused.
- CompilerIntrinsicsLib library now imported for AARCH64, as well as ARM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Randy Pawell <randy_pawell@hp.com>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16471 6f19259b-4bc3-4df7-8a09-765794883524
1. Add delay after set device address and get configuration descriptor.
2. Sync the change at R15876 in XhciDxe to do not access transfer ring when endpoint is isochronous type or control type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16105 6f19259b-4bc3-4df7-8a09-765794883524
1. Module UNI and Package UNI files are not DOS format. Convert them to DOS format.
2. Remove unused SectionExtractionDxeModStrs.uni and SectionExtractionPeiModStrs.uni
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16044 6f19259b-4bc3-4df7-8a09-765794883524
2. Add MODULE_UNI_FILE file that contains the localized Abstract and Description of a module.
a. Addresses an information gap between INF files and the UEFI Distribution Packaging Specification XML schema
b. There will be an associated update to UPT in BaseTools to consume MODULE_UNI_FILE and associated UNI file during UDP creation that performs the INF -> XML conversion.
c. There will be an associated update to UPT in BaseTools to produce MODULE_UNI_FILE and associated UNI file during UDP installation that performs the XML -> INF conversion.
3. Add Module Extra UNI file that provides the localized Name of a module.
a. [UserExtensions.TianoCore."ExtraFiles"] provides an easy method for a module to specify extra files not listed in [Sources] or [Binaries] sections to be added to a UDP without having to list the files in the UPT package information data file.
b. There will be an associated update to UPT in BaseTools to package up files listed in [UserExtensions.TianoCore."ExtraFiles"] during UDP creation.
c. UNI file contains localized name of a module to go along with the localized Abstract and Description from the MODULE_UNI_FILE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15963 6f19259b-4bc3-4df7-8a09-765794883524
1. Usage information in INF file comment blocks are either incomplete or incorrect.
This includes usage information for Protocols/PPIs/GUIDs/PCDs/HOBs/Events/BootModes.
The syntax for usage information in comment blocks is defined in the EDK II Module Information (INF) Specification
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15962 6f19259b-4bc3-4df7-8a09-765794883524
creation) of PciIoDevice->DevicePath. The bug can be triggered when
PciBusDxe is built into OVMF, with qemu/KVM device assignment of
a PCI-express device on the default 440FX machine type. OVMF
correctly discovers that the device is PCIe and begins probing
extended configuration space for the device. The root bridge
has no way to access extended config space and correctly errors,
sending us into the error reporting chain seen below. It's
possible that this error path could also be reproduced on physical
hardware when a PCI-to-PCIe bridge is present.
GatherDeviceInfo() | GatherPpbInfo() | GatherP2CInfo() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
CreatePciIoDevice() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
AllocateZeroPool()
LocateCapabilityRegBlock() [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoDevice->IsPciExp = TRUE
LocatePciExpressCapabilityRegBlock() [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoConfigRead() via funcptr [MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c]
RootBridgeIoPciRead() via funcptr [PcAtChipsetPkg/PciHostBridgeDxe/PciRootBridgeIo.c]
FAILS
REPORT_STATUS_CODE_WITH_DEVICE_PATH() [MdePkg/Include/Library/ReportStatusCodeLib.h]
ReportStatusCodeWithDevicePath() [MdeModulePkg/Library/DxeReportStatusCodeLib/ReportStatusCodeLib.c]
ASSERT (DevicePath != NULL) <--+
CreatePciDevicePath() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
sets PciIoDevice->DevicePath ----------+
In English:
- CreatePciIoDevice() allocates a zeroed out PCI_IO_DEVICE structure.
- PciIoConfigRead() tries to access the (extended) config space, and
fails.
- PciIoConfigRead() wants to report a status code (read error) for the
device path.
- Unfortuantely, PciIoDevice->DevicePath is still NULL at that point.
- The ASSERT() in ReportStatusCodeWithDevicePath() fires.
Fix it by moving CreatePciDevicePath() into CreatePciIoDevice(),
allowing PciIoDevice->DevicePath to be initialized before we
begin probing the device capabilities:
GatherDeviceInfo() | GatherPpbInfo() | GatherP2CInfo() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
CreatePciIoDevice() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
AllocateZeroPool()
CreatePciDevicePath() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
sets PciIoDevice->DevicePath -----------+
LocateCapabilityRegBlock() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoDevice->IsPciExp = TRUE |
LocatePciExpressCapabilityRegBlock() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoConfigRead() via funcptr | [MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c]
RootBridgeIoPciRead() via funcptr | [PcAtChipsetPkg/PciHostBridgeDxe/PciRootBridgeIo.c]
FAILS |
REPORT_STATUS_CODE_WITH_DEVICE_PATH() | [MdePkg/Include/Library/ReportStatusCodeLib.h]
ReportStatusCodeWithDevicePath() | [MdeModulePkg/Library/DxeReportStatusCodeLib/ReportStatusCodeLib.c]
ASSERT (DevicePath != NULL) <-----+
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15567 6f19259b-4bc3-4df7-8a09-765794883524
Platforms such as Xen already enumerates PCI bridges and devices. Use
this PCD to control EDK2 behavior.
PcdPciDisableBusEnumeration is placed under [PcdsFixedAtBuild,
PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx], so that it is
possible to alter it during runtime.
The default setting of this PCD is false (allow full PCI enumeration) to
preserve the same behavior before this change.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14940 6f19259b-4bc3-4df7-8a09-765794883524
1.Port reset process may not be proper for some vendor's SS hubs. If the corresponding port shows the reset has been done by C_RESET bit we have to skip the whole reset process for attached devices.
2.Clean C_BH_RESET bit immediately to avoid usb timer entering too many times when 5 tiers hubs are connected.
3.Stop checking URB if there is an error happened.
4.Better error handling for fast hot-plug.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14889 6f19259b-4bc3-4df7-8a09-765794883524
1) The Queue size field in create I/O submission/completion queue cmds is 0-based. the current code is 1-based.
2) a typo on allocated memory page size. it's inconsistent that some places is using 4 pages, but a place is using 6 pages.
3) a typo on PRP/SGL mechanism judgment. should directly use Psdt field rather than Opc field.
4) some platforms may not support UINT64 width access on MMIO register. Fix it to use two 32-bit width access.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Kinney Michael <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14657 6f19259b-4bc3-4df7-8a09-765794883524
the PCI Bus driver through the function call NotifyPhase().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14483 6f19259b-4bc3-4df7-8a09-765794883524
1.Fix the bug in interface parser logic for usb camera device. Reserve device address if the device doesn’t get disconnected.
2.Some usb 1.1 devices require the context evaluation immediately with actual max packet size after detecting the device max packet size.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14226 6f19259b-4bc3-4df7-8a09-765794883524
Signed-off-by: Sun Rui <rui.sun@intel.com>
Reviewed-by: Fan Jeff <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13189 6f19259b-4bc3-4df7-8a09-765794883524
1) Fix a bug on missing hub context evaluation operation.
2) If the usb keyboard device configuration has been set successfully, then don’t set configuration again.
Signed-off-by: erictian
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13087 6f19259b-4bc3-4df7-8a09-765794883524
1) XHCI host controller hw always provides more than 5 interrupters.
Now using interrupter 0 to accommodate all received events.
2) XHCI host controller hw always provides 32bytes context size.
Now it dynamically detect context size and construct it.
also solved several issues:
1) Divides 64byte width register access to two 32bit registers access because some XHCI chipsets cannot support a single 64bit access.
2) Remove halt host controller statement in UsbBusDriverBindingStop(). It has been done by host controller’s DriverBindingStop(). And XhciDriverBindingStop() need XHCI host controller is in running state because it need execute DISABLE_SLOT cmd to release h/w resource.
signed-off-by: erictian
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12785 6f19259b-4bc3-4df7-8a09-765794883524
Jiewen Yao
Star Zeng
Ruiyu Ni
Bi, Dandan
Hao Wu
Dandan Bi
Suman Prakash
Feng Tian
Thomas Huth
Ard Biesheuvel
Laszlo Ersek
Gary Lin
Giri P Mudusuru
Joe Zhou
Darbin Reyes
Ma, Maurice
Jordan Justen
Michael Kinney
Anbazhagan, Baraneedharan
Joseph Shifflett
Olivier Martin
Shumin Qiu
Randy Pawell
Samer El-Haj-Mahmoud
Gao, Liming
Elvin Li
Chen Fan
Eric Dong
Alex Williamson
Tian, Hot
Wei Liu
Sergey Isakov
erictian
niruiyu
li-elvin
rsun3
lgao4