In AtaAtapiPassThruStop(), if the device has been operating in AHCI mode,
we unmap the DMA buffers and then disable the device (including bus master
DMA). The order of these actions is wrong; we shouldn't unmap DMA buffers
until bus master DMA is turned off. Reverse the steps.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Both AtaAtapiPassThruStart() and AtaAtapiPassThruStop() fetch the
supported attributes of the device, just so they can toggle the
IO+MMIO+BusMaster subset.
After we compute this bitmask in AtaAtapiPassThruStart(), we can cache it
for later, and save the fetch in AtaAtapiPassThruStop().
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
We found there are loops of *2* Maps and only *1* Unmap and
the DMA buffer address is decreasing.
It is caused by the below code flow.
XhcAsyncInterruptTransfer ->
XhcCreateUrb ->
XhcCreateTransferTrb ->
Map Urb->DataMap (1)
Timer: loops of *2* Maps and only *1* Unmap
XhcMonitorAsyncRequests ->
XhcFlushAsyncIntMap ->
Unmap and Map Urb->DataMap (2)
XhcUpdateAsyncRequest ->
XhcCreateTransferTrb ->
Map Urb->DataMap (3)
This patch is to eliminate (3).
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The SPC-4 says about INQUIRY,
> In response to an INQUIRY command received by an incorrect logical unit,
> the SCSI target device shall return the INQUIRY data with the peripheral
> qualifier set to the value defined in 6.4.2. The INQUIRY command shall
> return CHECK CONDITION status only when the device server is unable to
> return the requested INQUIRY data.
When a device server takes the second branch, and returns CHECK CONDITION
for a nonexistent LUN, the InquiryData structure in the
DiscoverScsiDevice() function remains filled with the original zeros.
DiscoverScsiDevice() then sees zero in both Peripheral_Qualifier and
Peripheral_Type, and therefore ScsiBusDxe produces a ScsiIo protocol
instance with device type zero, for the nonexistent LUN.
Device type zero is EFI_SCSI_TYPE_DISK. Thus ScsiDiskDxe binds the bogus
ScsiIo protocol interface, and produces a similarly bogus BlockIo
interface on top. This ripples up to BDS, where UefiBootManagerLib can
auto-generate bogus UEFI boot options for the nonexistent LUNs.
This has been encountered with QEMU, after commit ded6ddc5a7b9 ("scsi:
clarify sense codes for LUN0 emulation", 2017-08-04). QEMU now answers
INQUIRY commands that were directed to nonexistent LUNs with:
> DiscoverScsiDevice:1361: Lun=2 HostAdapterStatus=0 TargetStatus=2
> SenseDataLength=18 InquiryDataLength=96
> Sense {
> Sense 000000 70 00 05 00 00 00 00 0A 00 00 00 00 25 00 00 00
> Sense 000010 00 00
> Sense }
> Inquiry {
> Inquiry 000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> Inquiry 000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> Inquiry 000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> Inquiry 000030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> Inquiry 000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> Inquiry 000050 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> Inquiry }
The interesting fields are:
- HostAdapterStatus=0 (OK),
- TargetStatus=2 (CHECK CONDITION),
- Sense/Error_Code=0x70 (Current error, Fixed description)
- Sense/Sense_Key=0x05 (ILLEGAL REQUEST)
According to SPC-4 "Table 41 -- Sense key descriptions (part 2 of 2)",
ILLEGAL REQUEST is justified when "the command was addressed to an
incorrect logical unit number".
Thus, recognize this kind of answer for nonexistent LUNs.
(
Checking the status fields and the sense data is justified anyway,
according to the documentation of ScsiInquiryCommand():
> @retval EFI_SUCCESS The command was executed
> successfully. See
> HostAdapterStatus,
> TargetStatus, SenseDataLength,
> and SenseData in that order for
> additional status information.
)
Cc: Eric Dong <eric.dong@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The code after the "if" statement is only reachable if the first branch
with the "break" is not taken. Therefore we can move the "else" branch
after the "if" statement, simplifying the code.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The SPC-4 spec says about the INQUIRY data, in "Table 138 -- Peripheral
qualifier":
> Qualifier = 011b The device server is not capable of supporting a
> peripheral device on this logical unit. For this
> peripheral qualifier the peripheral device type shall
> be set to 1Fh. All other peripheral device type values
> are reserved for this peripheral qualifier.
Accordingly, the DiscoverScsiDevice() function returns FALSE if
Peripheral_Qualifier is 3 decimal, but Peripheral_Type differs from 1Fh.
This is a valid sanity check -- such combinations are reserved.
When Peripheral_Qualifier is 3, and Peripheral_Type is 1Fh, then
DiscoverScsiDevice() returns TRUE. While this combination is not reserved,
returning TRUE for it is incorrect: Peripheral_Type 1Fh stands for
"Unknown or no device type", and this combination is returned in
particular when the INQUIRY command was directed to a nonexistent LUN.
Quoting the spec:
> In response to an INQUIRY command received by an incorrect logical unit,
> the SCSI target device shall return the INQUIRY data with the peripheral
> qualifier set to the value defined in 6.4.2. [...]
>
> [...]
>
> The PERIPHERAL QUALIFIER field and PERIPHERAL DEVICE TYPE field identify
> the peripheral device connected to the logical unit. If the SCSI target
> device is not capable of supporting a peripheral device connected to
> this logical unit, the device server shall set these fields to 7Fh
> (i.e., PERIPHERAL QUALIFIER field set to 011b and PERIPHERAL DEVICE TYPE
> field set to 1Fh).
The consequence of this bug is that for each nonexistent Target/LUN pair,
we produce a useless ScsiIo protocol interface. The internal
"ScsiIoDevice->ScsiDeviceType" field will be set to 0x1f, and it will be
returned to higher-level SCSI drivers when they call
ScsiIo->GetDeviceType().
Given that 0x1f means "Unknown or no device type", no higher-level driver
can ever support it, so these ScsiIo protocol interfaces are useless.
The fix is to return FALSE for the (Peripheral_Qualifier=3,
Peripheral_Type=0x1f) combination. With that however we reject the whole
Peripheral_Qualifier=3 space (justifiedly -- see the definition above),
which lets us simplify the code.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
V3 changes:
Add debug messages for new return path when successfully erase the
specified blocks. Refine logic for calculating the size for writing
zeros to device.
V2 changes:
The Trim command is not supported on all eMMC devices. For those devices
that do not support such command, add codes to handle the scenario.
Commit message:
The current implementation of the Erase Block Protocol service
EraseBlocks() uses the erase command. According to spec eMMC Electrical
Standard 5.1, Section 6.6.9:
The erasable unit of the eMMC is the "Erase Group"; Erase group is
measured in write blocks that are the basic writable units of the Device.
...
When the Erase is executed it will apply to all write blocks within an
erase group.
However, code logic in function EmmcEraseBlocks() does not check whether
the blocks to be erased form complete erase groups. Missing such checks
will lead to erasing extra data on the device.
This commit will:
a. If the device support the Trim command, use the Trim command to
perform the erase operations for eMMC devices.
According to the spec:
Unlike the Erase command, the Trim function applies the erase operation to
write blocks instead of erase groups.
b. If the device does not support the Trim command, use the Erase command
to erase the data in the erase groups. And write zeros to those blocks
that cannot form a complete erase group.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Per NVM Express Spec, software should notify NVME HW when shutdown
occurs.
The NVME controller requires notification for shutdown as part of
its management of internal structures. Even with FUA, failing to
notify the NVME controller to shutdown power off causes the NVME
controller to take quite some time to organize its tables on the
next power on. This time exceeds the normal timeout, so we would
fail to boot the NVME disk.
The host should set the Shutdown Notification (CC.SHN) field to 01b
to indicate a normal shutdown operation. The controller indicates
when shutdown processing is completed by updating the Shutdown Status
(CSTS.SHST) field to 10b.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
According to the Universal Flash Storage (UFS) Version 2.1 (JESD220C) spec
Section 10.7.8.5, the DATA SEGMENT LENGTH field of the UPIU shall also be
set to number of descriptor bytes to write.
The origin codes miss the above operation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
PciScanBus() assumes the GetResourcePadding() puts BUS descriptor
in the very beginning, if it's not, the Descriptors will be updated
to point to middle of the pool buffer, which can cause
FreePool(Descriptors) hang in DEBUG image.
No functionality impact to RELEASE image.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=644
According to XHCI spec:
4.10.2.1 Stall Error
4.10.2.4 Babble Detected Error
When a device transmits more data on the USB than the host controller
is expecting for a transaction, it is defined to be babbling.
In general, this is called a Babble Error. When a device sends more
data than the TD Transfer Size bytes (TD Babble), unexpected activity
that persists beyond a specified point in a (micro)frame (Frame Babble),
or a packet greater than Max Packet Size (Packet Babble), the host
controller shall set the Babble Detected Error in the Completion Code
field of the TRB, generate an Error Event, and halt the endpoint
(refer to Section 4.10.2.1).
This patch is to also check for EFI_USB_ERR_BABBLE error returned as
a TransferResult and then proceed to XhcRecoverhaltedEndPoint.
Cc: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Adds the implementation of Disk Information Protocol for EMMC devices per
PI 1.6 spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Adds the implementation of Disk Information Protocol for SD devices per
PI 1.6 spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=433
When a blocking NVMe PassThru request experiences timeout, the current
codes in function NvmExpressPassThru() do not abort the timeout request
while advancing synchronous Submission Queue tail. Therefore, it is
possible to submit a new blocking PassThru request when the synchronous
Submission Queue is full.
The commit adds logic to abort the timeout request by resetting the NVMe
controller when a timeout occurs for a blocking PassThru request.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This fixes BULK data loss when transfer is detected as timeout but
finished just before stopping endpoint.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
The patch separates the common logic in XhcControlTransfer,
XhcBulkTransfer and XhcSyncIntTransfer to a sub-routine
XhcTransfer. It doesn't have functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Current implementation of IsTransferRingTrb only checks whether
the TRB is in the RING of the URB.
The patch enhanced the logic to check that whether the TRB belongs
to the transaction of URB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
The SATA spec mandates that link detection by the PHY completes within
10 ms after receiving a reset signal. However, there is no obligation
to uphold this requirement at the driver end as strictly as we do, and
as it turns out, some combinations of host and device (e.g., Samsung
850 EVO connected to a LeMaker Cello) are only borderline compliant,
which means the device is not detected reliably.
So let's allow for a bit of margin, and increase the PHY detect timeout
value to 15 ms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some USB devices don't report data periodically through Int
Transfer. They report data only when be asked. If the TRB
is not removed from the XHCI HW, when next time HOST asks
data again, the data is reported but consumed by the previous
TRB, which results the HOST thinks data never comes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When "reconnect -r" is typed in shell, UsbFreeInterface() is called
to uninstall the UsbIo and DevicePath. But When a UsbIo is opened
by a driver and that driver rejects to close the UsbIo in Stop(),
the uninstall doesn't succeed.
But UsbFreeInterface () frees the DevicePath memory without check
whether the uninstall succeeds.
It leads to the DXE core database contain a DevicePath instance but
that instance's memory is freed.
Assertion happens when someone calls InstallProtocol(DevicePath)
because the InstallProtocol() checks all DevicePath instance to
find whether the same one exits in database.
We haven't seen any USB device driver which rejects to close UsbIo
in Stop(), but it's very likely.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=510
The commit fills the 'Interval' field of the Endpoint Context data for
isochronous endpoints. It will resolve the error when a Configure
Endpoint Command is sent to an isochronous endpoint.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
If IOMMU protocol is installed, PciBus need call IOMMU
to set access attribute for the PCI device in Map/Ummap.
Only after the access attribute is set, the PCI device can
access the DMA memory.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Previous patch Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Previous patch Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
If IOMMU protocol is installed, PciHostBridge just calls
IOMMU AllocateBuffer/FreeBuffer/Map/Unmap.
PciHostBridge does not set IOMMU access attribute,
because it does not know which device request the DMA.
This work is done by PciBus driver.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Previous patch Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Previous patch Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
For function UfsPassThruGetTargetLun(), the length of the input device
node specified by 'DevicePath' should be compared with the size of
'UFS_DEVICE_PATH' rather than the size of 'SCSI_DEVICE_PATH'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In function UfsHcDriverBindingStart(), the return value 'Status' may be
overridden during the original PCI attributes restore process.
This commit refines the logic to avoid such override.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit removes the unused field 'EFI_HANDLE Handle' in Ufs host
controller private data structure 'UFS_HOST_CONTROLLER_PRIVATE_DATA'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In case of an async command if updating the submission queue tail
doorbell fails then the command will not be picked up by device and
no completion response will be created. This scenario has to be handled.
Also if we create an AsyncRequest element and insert in the async queue,
it will never receive a completion so in the timer routine this element
won't be freed, resulting in memory leak. Also in case of blocking calls
we should capture the status of updating completion queue head doorbell
register and return it to caller of PassThru.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Suman Prakash <suman.p@samsung.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
In the origin codes, the host sets the fDeviceInit flag to initiate device
initialization, but does not check whether the device resets this flag
to indicate the device initialization is completed.
Details can be referred at UFS 2.0 Spec Section 14.2 - Flags.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function PeiUsbReadCapacity(), the following expression:
LastBlock = (Data.LastLba3 << 24) |
(Data.LastLba2 << 16) |
(Data.LastLba1 << 8) |
Data.LastLba0;
(There is also a similar case in function PeiUsbReadFormattedCapacity().)
will involve undefined behavior in signed left shift operations.
Since Data.LastLbaX is of type UINT8, they will be promoted to int (32
bits, signed) first, and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Data.LastLba3 is 1, (Data.LastLba3 << 24) will be out of
the range within int type. The undefined behavior of the signed left shift
might incur potential issues.
This commit will add an explicit UINT32 type cast for Data.LastLba3 to
refine the codes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function UfsBlockIoPeimGetMediaInfo(), the following expression:
Private->Media[DeviceIndex].LastBlock = (Capacity16.LastLba3 << 24) |
(Capacity16.LastLba2 << 16) |
(Capacity16.LastLba1 << 8) |
Capacity16.LastLba0;
(There is also a similar case in this function.)
will involve undefined behavior in signed left shift operations.
Since Capacity16.LastLbaX is of type UINT8, and
Private->Media[DeviceIndex].LastBlock is of type UINT64. Therefore,
Capacity16.LastLbaX will be promoted to int (32 bits, signed) first, and
then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Capacity16.LastLba3 is 1, (Capacity16.LastLba3 << 24) will
be out of the range within int type. The undefined behavior of the signed
left shift will lead to a potential of setting the high 32 bits of
Private->Media[DeviceIndex].LastBlock to 1 during the cast from type int
to type UINT64.
This commit will add an explicit UINT32 type cast for Capacity16.LastLba3
to resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function ReadCapacity(), the following expression:
MediaInfo->LastBlock = (Data.LastLba3 << 24) |
(Data.LastLba2 << 16) |
(Data.LastLba1 << 8) |
Data.LastLba0;
(There is also a similar case in this function.)
will involve undefined behavior in signed left shift operations.
Since Data.LastLbaX is of type UINT8, and MediaInfo->LastBlock is of type
UINTN. Therefore, Data.LastLbaX will be promoted to int (32 bits, signed)
first, and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Data.LastLba3 is 1, (Data.LastLba3 << 24) will be out of
the range within int type. The undefined behavior of the signed left shift
will lead to a potential of setting the high 32 bits of
MediaInfo->LastBlock to 1 during the cast from type int to type UINT64
for X64 builds.
This commit will add an explicit UINT32 type cast for Data.LastLba3 to
resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In function GetMediaInfo(), the following expression:
ScsiDiskDevice->BlkIo.Media->LastBlock = (Capacity10->LastLba3 << 24) |
(Capacity10->LastLba2 << 16) |
(Capacity10->LastLba1 << 8) |
Capacity10->LastLba0;
will involve undefined behavior in signed left shift operations.
Since Capacity10->LastLbaX is of type UINT8, and
ScsiDiskDevice->BlkIo.Media->LastBlock is of type UINT64. Therefore,
Capacity10->LastLbaX will be promoted to int (32 bits, signed) first,
and then perform the left shift operation.
According to the C11 spec, Section 6.5.7:
4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
bits are filled with zeros. If E1 has an unsigned type, the value
of the result is E1 * 2^E2 , reduced modulo one more than the
maximum value representable in the result type. If E1 has a signed
type and nonnegative value, and E1 * 2^E2 is representable in the
result type, then that is the resulting value; otherwise, the
behavior is undefined.
So if bit 7 of Capacity10->LastLba3 is 1, (Capacity10->LastLba3 << 24)
will be out of the range within int type. The undefined behavior of the
signed left shift will lead to a potential of setting the high 32 bits
of ScsiDiskDevice->BlkIo.Media->LastBlock to 1 during the cast from type
int to type UINT64.
This commit will add an explicit UINT32 type cast for
Capacity10->LastLba3 to resolve this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
For async commands, the buffer allocated for Prp list is
not getting freed, which will cause memory leak for async
read write command. For example testing async command flow
with custom application to send multiple read write commands
were resulting in decrease of available memory page in memmap,
which eventually resulted in system hang. Hence freeing
AsyncRequest->MapData, AsyncRequest->MapMeta, AsyncRequest->MapPrpList and
AsyncRequest->PrpListHost when async command is completed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Suman Prakash <suman.p@samsung.com.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
At worst case, OCR register may always not set BIT31. It will cause
original code enter to dead loop. Adding a break for such case.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
There are cases that the operands of an expression are all with rank less
than UINT64/INT64 and the result of the expression is explicitly cast to
UINT64/INT64 to fit the target size.
An example will be:
UINT32 a,b;
// a and b can be any unsigned int type with rank less than UINT64, like
// UINT8, UINT16, etc.
UINT64 c;
c = (UINT64) (a + b);
Some static code checkers may warn that the expression result might
overflow within the rank of "int" (integer promotions) and the result is
then cast to a bigger size.
The commit refines codes by the following rules:
1). When the expression is possible to overflow the range of unsigned int/
int:
c = (UINT64)a + b;
2). When the expression will not overflow within the rank of "int", remove
the explicit type casts:
c = a + b;
3). When the expression will be cast to pointer of possible greater size:
UINT32 a,b;
VOID *c;
c = (VOID *)(UINTN)(a + b); --> c = (VOID *)((UINTN)a + b);
4). When one side of a comparison expression contains only operands with
rank less than UINT32:
UINT8 a;
UINT16 b;
UINTN c;
if ((UINTN)(a + b) > c) {...} --> if (((UINT32)a + b) > c) {...}
For rule 4), if we remove the 'UINTN' type cast like:
if (a + b > c) {...}
The VS compiler will complain with warning C4018 (signed/unsigned
mismatch, level 3 warning) due to promoting 'a + b' to type 'int'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
For pointer subtraction, the result is of type "ptrdiff_t". According to
the C11 standard (Committee Draft - April 12, 2011):
"When two pointers are subtracted, both shall point to elements of the
same array object, or one past the last element of the array object; the
result is the difference of the subscripts of the two array elements. The
size of the result is implementation-defined, and its type (a signed
integer type) is ptrdiff_t defined in the <stddef.h> header. If the result
is not representable in an object of that type, the behavior is
undefined."
In our codes, there are cases that the pointer subtraction is not
performed by pointers to elements of the same array object. This might
lead to potential issues, since the behavior is undefined according to C11
standard.
Also, since the size of type "ptrdiff_t" is implementation-defined. Some
static code checkers may warn that the pointer subtraction might underflow
first and then being cast to a bigger size. For example:
UINT8 *Ptr1, *Ptr2;
UINTN PtrDiff;
...
PtrDiff = (UINTN) (Ptr1 - Ptr2);
The commit will refine the pointer subtraction expressions by casting each
pointer to UINTN first and then perform the subtraction:
PtrDiff = (UINTN) Ptr1 - (UINTN) Ptr2;
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Compiler calculates the PciBar[BarIndex] using
sizeof (PciBar[0]) * BarIndex, when BarIndex is type of UINT64,
the above calculation generates assembly code using _allmul.
Change BarIndex to UINTN to avoid the build failure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
When the VendorId/DeviceId/RevisionId/SubsystemVendorId
/SubsystemDeviceId is MAX_UINTN, IncompatiblePciDeviceSupport
driver doesn't use it to match any IDs.
The patch fixes this bug.
Since PciBus driver always calls IncompatiblePciDeviceSupport
using IDs read from HW, MAX_UINTN is never passed to this
driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The patch replaces the following macros:
DEVICE_ID_NOCARE (0xFF) --> MAX_UINT64
PCI_ACPI_UNUSED (0) --> 0
PCI_BAR_ALL (0xFF) --> MAX_UINT64
PCI_BAR_NOCHANGE (0) --> 0
PCI_BAR_EVEN_ALIGN --> EVEN_ALIGN (local definition)
Since the PciBus driver was updated to accept Spec defined values
in previous commit, the above replacements don't impact
functionality.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
PI spec IncompatiblePciSupport part defines (UINT64)-1 as all BARs
and 0 to use existing alignment. PciBus driver didn't accept these
values. It treated 0xFF as all BARs and 0xFFFFFFFFFFFFFFFFULL to use
existing alignment.
The patch changes the code to still accept old values while also
accept values defined in PI spec. So that the driver can provide
backward compatibility and follow spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When BarIndex equals to 0xFF, default value 0 is used as the BAR
index. Though PCI_BAR_ALL and MAX_UINT8 shares the same value,
using PCI_BAR_ALL is like to match any BAR not BAR 0, it's more
proper to use MAX_UINT8 here.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If the code eventually returns "Status" anyway, it does not make
sense to explicitly return "Status" in case of an error, too.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UPIU packet is sent, (BIT0 << Slot) should be set according
to context. But BIT0 is used without Slot when UfsWaitMemSet ()
is invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UPIU packet is sent, (BIT0 << Slot) should be set according
to context. But BIT0 is used without Slot when UfsWaitMemSet ()
is invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UFS_HC_CAP_64ADDR bit is set, it means 64-bit address,
not 32-bit address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Refine the codes to compare the definition 'SIZE_4GB' with type
EFI_PHYSICAL_ADDRESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Add support for non-coherent DMA, either by performing explicit cache
maintenance when DMA mappings are aligned to the CPU's DMA buffer alignment,
or by bounce buffering via uncached mappings otherwise.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Fix switch/case statement type mismatch in functions PciIoMemRead &
PciIoMemWrite.
Parameter 'Width' is of enum type EFI_PCI_IO_PROTOCOL_WIDTH, but the enum
type provided in 'switch (Width)' block is of type
EFI_PCI_ROOT_BRIDGE_IO_PROTOCOL_WIDTH.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Add missing EFIAPI modifiers to the functions that are exposed via the
PCI I/O protocol.
At the same time, add a missing UINT8 cast which breaks the build on
Visual Studio.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
This implements support for non-discoverable PCI compatible devices, i.e,
devices that are not on a PCI bus but that can be controlled by generic PCI
drivers in EDK2.
This is implemented as a UEFI driver, which means we take full advantage
of the UEFI driver model, and only instantiate those devices that are
necessary for booting.
Care is taken to deal with DMA addressing limitations: DMA mappings and
allocations are moved below 4 GB if the PCI driver has not informed us
that the device being driven is 64-bit DMA capable. DMA is implemented as
coherent, support for non-coherent DMA is implemented by a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Port status bits are clear in original code, so no enumeration
takes place.
Changing this to prevent the status bits from being cleared
allows enumeration to proceed normally.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Mike Turner <Michael.Turner@microsoft.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mike Turner <Michael.Turner@microsoft.com>
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit e27cca has a typo on DEBUG level macro. And this debug
message should be DEBUG_INFO rather than DEBUG_ERROR.
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
reviewed-by: Marcin Wojtas <mw@semihalf.com>
EFI_D_INFO, EFI_D_VERBOSE, EFI_D_WARN and EFI_D_ERROR are replaced
with currently recommended values.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to AHCI Spec 1.3 GHC.AE bit description:
"The implementation of this bit is dependent upon the value of the
CAP.SAM bit. If CAP.SAM is '0', then GHC.AE shall be read-write and shall
have a reset value of '0'. If CAP.SAM is '1', then AE shall be read-only
and shall have a reset value of '1'."
Being in AhciMode, for proper operation it is required, that GHC.AE bit
is always set, before any other AHCI registers are written to. Current
AhciMode implementation, both in AhciReset() and AhciModeInitialization()
functions, set GHC.AE bit only depending on 'CAP.SAM == 0' condition,
assuming (according to the AHCI spec), that otherwise it has to be set
anyway. It may however happen, that even if 'CAP.SAM == 1', GHC.AE
requires updating by software.
This patch enables in AhciMode setting GHC.AE in case its initial value
is '0'. It fixes AHCI support for Marvell Armada 70x0 and 80x0 SoC
families. The change is transparent to all other platforms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
We send ADDRESS DEVICE CMD in XhcInitializeDeviceSlot(), which will
cause XHC issue a USB SET_ADDRESS request to the USB Device.
According to USB spec, there should have a 10ms delay before this
operation after resetting a given port.
But in original code, there is a possible path which may have no such
10ms delay:
UsbHubResetPort()->UsbHubSetPortFeature()->Stall(20)->UsbHubGetPortSt
atus()->XhcPollPortStatusChange()->(if RESET_C bit is set)->
XhcInitializeDeviceSlot()->(if RESET_C bit is set)->Stall(10)
So this patch is used to fix above issue.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Tested-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch is used to revert changes done in commit 17f3e942
bc527fbd75068d2d5752b6af54917487 - "MdeModulePkg/UsbMass: Not
retry if usb bot transfer execution fail"
It's because Usb Floppy will report DEVICE_ERROR for the first
several cmds when it need spin up. so retry logic makes sense.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When PciSioSerial is firstly started with a non-NULL remaining
device path, the UART instance is created using the parameters
specified in the remaining device path. Later when the driver
is started again on the same UART controller with NULL remaining
device path, the correct logic is to directly return SUCCESS
instead of current buggy implementation which wrongly produces
another UART using the default parameters.
The bug causes two UARTs are created when the UART is configured
in 57600 baud rate.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
According to UFS Host Controller Spec(JESD223), the bits 1:0 of this
DataByteCount field shall be 11b to indicate Dword granularity.
But the size of UFS Request Sense Data Response defined in UFS Spec
(JESD220C) is 18 which is not Dword aligned, we would have to round
down to the multiple of 4 to fill the DBC field to avoid bring issue
on some UFS HCs.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Short Packet case is a normal case, we shouldn't print it as an error
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
AhciDumpPortStatus doesn't fully populate all the fields of
AtaStatusBlock after completing command execution, which may bring
issue if someone depends on the return status.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The 'universal' PCI bus driver in MdeModulePkg contains a quirk to
degrade 64-bit PCI MMIO BARs to 32-bit in the presence of an option
ROM on the same PCI controller.
This quirk is highly specific to not just the X64 architecture in general,
but to the PC platform in particular, given that only X64 platforms that
require legacy PC BIOS compatibility require it. However, making the
quirk dependent on the presence of the legacy BIOS protocol met with
resistance, due to the fact that it introduces a dependency on the
IntelFrameworkModulePkg package.
So instead, make the quirk configurable, by introducing a feature flag PCD
'PcdPciDegradeResourceForOptionRom' which defaults to TRUE only for X64.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Currently, the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute is completely
ignored by the PCI host bridge driver, which means that, on an implementation
that supports DMA above 4 GB, allocations above 4 GB may be provided to
devices that have not expressed support for it.
So in addition to checking 'RootBridge->DmaAbove4G' to establish whether the
root bridge itself supports DMA above 4 GB, we must also take into account
the operation type (EfiPciOperationBusMaster{Read|Write|CommonBuffer}64),
and the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute, when mapping and
allocating DMA memory, respectively.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Since current codes in NvmExpressDxe already support the non-blocking I/O
feature for EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL interface, the relative bit
in the 'Attributes' field of EFI_NVM_EXPRESS_PASS_THRU_MODE should be set
to reflect this.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit fixes the issue that the caller event passed to
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() will not be signaled for
NVME Admin commands.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru()
should return EFI_INVALID_PARAMETER if the input 'NamespaceId' is invalid
for the NVM Express controller. This commit adds check in PassThru() to
follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit adds serveral checks for the 'Packet' parameter passed to the
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() API:
The check for the 'TransferLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value will not
exceed the maximum data transfer size allowed by a controller.
The check for the 'TransferBuffer' and 'TransferLength' fields in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET when the Opcode of an NVME
command indicates a data transfer between controller and host.
The check for the 'MetadataLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value is not 0
when the corresponding 'MetadataBuffer' field has a non-NULL value.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to UEFI spec, an EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL with neither
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_LOGICAL nor
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_PHYSICAL set in the Attributes field
is an illegal configuration.
This commit adds this check in the PassThru API to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, the 'TransferBuffer' and 'MetadataBuffer' used
in a data transfer should be aligned on the boundary specified by the
IoAlign field in the EFI_NVM_EXPRESS_PASS_THRU_MODE structure.
This commit adds this check to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNextNamespace() should return
EFI_NOT_FOUND when the value pointed to by NamespaceId is the namespace ID
of the last namespace on the NVM Express controller. This commit modifies
the check for NamespaceId to follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNamespace() should return
EFI_NOT_FOUND when the input DevicePath is a device path node type that
the NVM Express Pass Thru driver supports, but there is not a valid
translation from DevicePath to a namespace ID. Current code will return
EFI_SUCCESS. This commit adds additional check in the GetNameSpace API to
make sure correct status is returned.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.BuildDevicePath() should return
EFI_NOT_FOUND when the input NamespaceId is not valid. However, current
code returns EFI_DEVICE_ERROR instead. This commit modifies the check for
input NamespaceId to return the correct status.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The gBS->OpenProtocol() calls to open EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL
in NvmExpress.c will crash the data in 'Mode' field of
'Private->Passthru'.
The third parameter of gBS->OpenProtocol() is an output parameter that
stores the address where a pointer to the corresponding Protocol
Interface. The current code mistakenly pass '&Private->Passthru' (a
pointer of the EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL) as the third
parameter. This will crash the data in 'Mode' filed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The retry mechanism will bring issue if the usb device is unplugged
from XHCI HC but s/w is trying to access it through BlockIo. The
current cmd will get device error return status, but the sequential
cmds will be timeout. This behavior will cause system unresponsive
for a long while and bring bad user experience.
So we break the retry loop if found device error.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The last TRB in transfer ring is a LINK type TRB, which shouldn't
be accounted as a valid item in IsAsyncIntTrb().
Without this fix, the original algo will bring issue on those URBs
whose TRBs crosses the transfer ring.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This change is used to remove the port status polling in port reset
functions.
Why it's needed is because:
1) The same polling on same port has taken place prior to this removed
one. See UsbEnumeratePort()->GetPortStatus(). So this polling in
UsbEnumerateNewDev()->ResetPort() is redundant.
2) EDKII Xhci driver hooks all GetPortStatus() operations. If we don't
remove this one, XHCI driver's XhcPollPortStatusChange() may enter twice
in reset process and wrongly think the device is unplugged.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The Host Controller reset has been done at EDKII UHCI/EHCI/XHCI, The
original code will do twice host controller initialization which is
unnecessary. It also bring issues on some USB HCs.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
> cc1: warnings being treated as errors
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:
> In function 'GetProposedResources':
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:1388:
> error: integer constant is too large for 'long' type
Append a ULL suffix to the replacement text of PCI_RESOURCE_LESS that is
aligned with the style of the EFI_RESOURCE_SATISFIED and
EFI_RESOURCE_NOT_SATISFIED macros.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Section 7.8.2 of the PCI Express specification (r4.0 v0.3), entitled "PCI
Express Capabilities Register (Offset 02h)", and section 7.8.9 "Slot
Capabilities Register (Offset 14h)" of the same, describe the conditions
when a PCIe port should be considered "supporting hotplug":
- it should be a root complex port or a switch downstream port, and
- it should have the "Slot Implemented" bit set in the Express
Capabilities Register, and
- it should have the "Hot-Plug Capable" bit set in the Slot Capabilities
Register.
The first two sub-conditions are already implemented in at least two open
source projects I could find:
- in SeaBIOS by Marcel Apfelbaum: "hw/pci: reserve IO and mem for pci
express downstream ports with no devices attached"
<https://code.coreboot.org/p/seabios/source/commit/3aa31d7d6375>,
- in edk2 itself, in the implementation of the "PCI" UEFI Shell command:
see the "PcieExplainTypeSlot" case label in function
PciExplainPciExpress(), file
"ShellPkg/Library/UefiShellDebug1CommandsLib/Pci.c".
PciBusDxe recognizes such PCIe ports as bridges, but it doesn't realize
they support hotplug. In turn PciBusDxe omits getting any resource padding
information from the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL for these
bridges:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Implement a function called SupportsPcieHotplug() for identifying such
ports, and call it from IsPciHotPlugBus() (after the call to IsSHPC()).
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
The PCI Hot Plug capability register block is marked with capability ID
0x0C (EFI_PCI_CAPABILITY_ID_SHPC), not 0x06
(EFI_PCI_CAPABILITY_ID_HOTPLUG).
This bug prevents PciBusDxe from recognizing whether a PCI-to-PCI bridge
supports hotplug. In turn the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL is
not consulted for resource padding information:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
IsSHPC() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Look for the correct capability ID.
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
If there is no port multiplier (PortMultiplierPort = 0xFFFF), current code
in functions TransferAtaDevice() and TrustTransferAtaDevice() will always
set the DEV bit of the ATA device register. It causes that ATA commands
cannot be sent to some ATA hard drives.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
- abstrated to abstracted
- accessibla to accessible
- addres to address
- apropriate to appropriate
- arry to array
- availabe to available
- avaliable to available
- becasue to because
- correponding to corresponding
- etablished to established
- exeuction to execution
- extensiable to extensible
- fileds to fields
- loadding to loading
- ptototypes to prototypes
- prococol protocol
- requried to required
- resoruce to resource
- runing to running
- uild to build
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The commit makes sure that the elements in array 'SwitchResp' get
initialized before being used.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This change is to avoid UEFI SCT failure as UEFI SCT has no knowledge
about how to accessing a EMMC RPMB partition.
The user needs to access RPMB partition should get access through
EFI_SD_MMC_PASS_THRU protocol with authentication key & mac.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
We have to upgrade the TPL level used by SdMmc stack because the
following flow:
DiskIo2ReadWriteDisk() in logical partition -> PartitionReadBlocksEx()
in logical partition at TPL callback level -> ProbeMediaStatusEx()
with sync request -> DiskIo2ReadWriteDisk() in physical partition ->
waiting for async task completion.
if the low layer driver doesn't run at TPL_NOTIFY level, it will have
no time to trigger async task and cause system hang.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
According to spec if the length of a descriptor is smaller than
what the specification defines, then the host shall ignore it.
However if the size is greater than expected the host will ignore
the extra bytes and start looking for the next descriptor
at the end of actual length returned. Original check did not
handle the latter case correctly and only allowed descriptors
with lengths exactly as defined in specification.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evgeny Yakovlev <insoreiges@gmail.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This delay is necessary for eMMC reset to working properly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joe Zhou <shjzhou@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
It is enough to set PxCMD.FRE bit, which cause HBA to post received FISes
into the FIS receive area. According to AHCI Specification, only polling on
PxCMD.FRE to be cleared is necessary, when it is needeed to stop FIS engine
(eg. in order to change PxCMD.FB address).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
It is the follow up of 3ab41b7a32
to replace UnicodeStrToAsciiStr/AsciiStrToUnicodeStr with
UnicodeStrToAsciiStrS/AsciiStrToUnicodeStrS.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
If there is no multiplier, the DEV bit of the ATA device register would
always be set. It causes that some ATA hard drives don't response the
ATA identity command sent to them.
Below is the description about DEV bit in ATA spec:
A device is selected when the DEV bit of the Device register is equal to
the device number assigned to the device by means of a Device 0/Device 1
jumper or switch, or use of the CSEL signal.
Below is the description about DEV bit in SATA spec:
When the DEV bit in the Device register is set to one, selecting the
non-existent Device 1, the host adapter shall respond to register reads
and writes as specified for a Device 0 with no Device 1 present, as
defined in the ATA/ATAPI-5 standard.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The Maximum Queue Entries Supported (MQES) field in the CAP (Controller
Capabilities) register for a NVMe controller restrict the maximum
individual queue size that the controller supports.
The origin code does not check this value and always uses a hardcode value
when creating I/O submission/completion queues for asynchronous
transmission. The hardcode value might be larger than the MQES field, this
will lead to an 'Invalid Queue Size' error when creating I/O
submission/completion queues.
The patch will add checks to make sure proper queue size is passed when
creating I/O submission/completion queues.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Move NvmExpressHci.h definitions to a public industry standard
header in MdePkg. The NvmExpressHci.h contains definitions based
on the NVMe v1.1 specification. These definitions should be in
a public header so that clients of the NVMe passthru protocol
can use them to execute NVMe commands.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Darbin Reyes <darbin.emm.reyes@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The driver entry point calls gDS->SetMemorySpaceAttributes().
This interface may return EFI_NOT_AVAILABLE_YET when CPU Arch
protocol is not available.
So we need to list CpuArch protocol in its INF dependency section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
PciBus driver originally always degrade (64->32) the MMIO resource
for PCI BAR when the PCI device contains option ROM.
But the degrade causes the PCI device can only use resource below 4GB
which makes the resource allocation fails when the PCI device wants
very big MMIO.
The patch follows the PI spec (ECR 1529) to honor the granularity
setting for PCI BAR from IncompatiblePciDeviceSupport so that even
for PCI device which contains option ROM, the degrade doesn't happen
if IncompatiblePciDeviceSupport returns 64 as granularity.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Remove "Efi" from gEfiIncompatiblePciDeviceSupport to shorten
the global variable name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
This patch implements the EFI_ERASE_BLOCK_PROTOCOL in ScsiDiskDxe driver.
For now, the codes support the erase block feature only on Universal Flash
Storage (UFS) devices.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Together with EFI_BLOCK_IO_PROTOCOL, EFI_BLOCK_IO2_PROTOCOL is also
produced on NVMe devices.
The following Block I/O 2 functions are implemented:
Reset
ReadBlocksEx
WriteBlocksEx
FlushBlocksEx
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When PcdPciDisableBusEnumeration is enabled, the PciBus driver
might get into a dead loop if the secondary bus register on PCI
bridge is not programmed or programmed improperly. Adding this
check to avoid any potential dead loop caused by this.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Lee Leahy <Leroy.p.leahy@intel.com>
The Mantis ticket 1353 <https://mantis.uefi.org/mantis/view.php?id=1353>
and Mantis ticket 1472 <https://mantis.uefi.org/mantis/view.php?id=1472>
updated the description of the port multiplier port number parameter in
SATA Device Path Node and ATA Pass-Through Protocol.
Now, this parameter should be set to 0xFFFF instead of 0 to indicate that
an ATA device is directly attached on the controller port.
Please note that this is an incompatible change. The consumer of SATA
device path or ATA_PASS_THRU needs to re-examine its usage to follow UEFI
2.5 mantis 1353 and 1472.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Change PciHostBridgeDxe driver to not install the
PciHostBridgeResourceAllocation protocol and let
PciRootBridgeIo.Configuration() return the correct PCI resource
assignment information when the ResourceAssigned is TRUE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
When the aperture base equals to aperture limit, the old code treats
the aperture as non-existent. It's not correct because it indicates
a range starting with base and the length is 1.
The new code corrects the comparing bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The patch aligns to the IntelFrameworkModulePkg/Bus/Isa/IsaSerialDxe
driver not flush the UART in Reset() and SetAttributes() function.
It was found the flush causes hang on certain PCI serial devices.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Jin <eric.jin@intel.com>
Before switch to a bus mode, we need check if the SD device supports
this bus mode.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code is using ADMA mode to do clock tuning procedure. It
may have problem on some SD/MMC host controllers as there is no way to
know when to send next tuning cmd.
Update it to PIO mode to strictly follow SD Host Controller Simplified
Specification 3.0 Figure 2-29. By this way, if the Buffer Read Ready
interrupt is set, we could know it's ok to send the next clock tuning
cmd.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code has a bug to calculate which clock freq should be
used when the target clock freq is larger than the BaseClock Freq
provided by the system.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Check if the card is identified/initialized correctly. if not, break
the following cmd execution through PassThru()/ResetDevice().
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The "IoAlign" field in EFI_BLOCK_IO_MEDIA of an NVMe device is not
initialized properly, leading to a zero value for this field.
It should be initialized from the "IoAlign" field in the
EFI_NVM_EXPRESS_PASS_THRU_MODE structure maintained by the NVMe
controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The USB flash drive with Vendor ID 0x1516 (CompUSA) and Product ID 0x6221
returns a broken "Supported VPD Pages" VPD page. In particular, the
PageLength field has the invalid value 0x0602 (decimal 1538).
This prevents the loop from terminating that scans for the Block Limits
VPD page code in ScsiDiskInquiryDevice():
for (Index = 0; Index < PageLength; Index++) {
because the Index variable has type UINT8, and it wraps from 255 to 0,
without ever reaching PageLength (1538), and because
EFI_SCSI_PAGE_CODE_BLOCK_LIMITS_VPD does not occur at offsets 0 through
255.
* The fix is not to change the type of Index to UINT16 or a wider type.
Namely, section
7.8.14 Supported VPD Pages VPD page
in the "SCSI Primary Commands - 4" (SPC-4) specification names the
following requirement:
The supported VPD page list shall contain a list of all VPD page codes
(see 7.8) implemented by the logical unit in ascending order beginning
with page code 00h.
Since page codes are 8-bit unsigned quantities, it follows that the
maximum size for the Supported VPD Pages VPD page is 0x100 bytes, in
which every possible page code (0x00 through 0xFF) will be found, before
the UINT8 offset wraps around.
(EFI_SCSI_SUPPORTED_VPD_PAGES_VPD_PAGE.SupportedVpdPageList is correctly
sized as well, in "MdePkg/Include/IndustryStandard/Scsi.h".)
* Instead, add sanity checks that enforce the above requirement. If the
device breaks the spec, simply fall back to the "Block Limits page
absent" case.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1330955
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If the current PCI configuration requires no resources to be allocated at
all (i.e., unpopulated bus), the PCI enumeration code creates a single
ACPI_ADDRESS_SPACE_DESCRIPTOR memory descriptor with all fields cleared.
This is rejected by the SubmitResources() implementation of the generic
PciHostBridgeDxe in the following way:
PciHostBridge: SubmitResources for PcieRoot(0x0)
Mem: Granularity/SpecificFlag = 0 / 00
Length/Alignment = 0x0 / 0x0
PciBus: HostBridge->SubmitResources() - Invalid Parameter
ASSERT_EFI_ERROR (Status = Invalid Parameter)
ASSERT [PciBusDxe] .../PciBusDxe/PciLib.c(561): !EFI_ERROR (Status)
So instead, create the empty configuration as a single entry of type
EFI_ACPI_END_TAG_DESCRIPTOR.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Phase Tag, SqTdbl/CqHdbl and SqBuffer/CqBuffer should be cleared in
NvmeControllerInit() to make HC functionality work when user invokes
NvmeBlockIoReset().
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
In EnumerateNvmeDevNamespace(), when Private->ControllerData->Sn and/or
Private->ControllerData->Mn are NOT null-terminated strings,
UnicodeSPrintAsciiFormat(…) may generate unexpected (garbage) output
string.
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Memory pointed to by Private->ControllerData has not been freed up
correctly at error handling path.
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
The close brace of EmmcDxeComponentNameGetControllerName should be
at the beginning of a line.
Cc: Qiu Shumin <shumin.qiu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
According to SD Host Controller 3.0 spec figure 3-10, we have to wait
1ms before checking DAT[3:0] in voltage switch proc
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The original code doesn't reset the slot when there is device change.
It may bring issue on device identification procedure of some SD cards.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@Intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
If there is no card presented before power on, there would
have no card change interrupt generated. This is a corner
case which can't be handled by old logic.
The patch is used to move card present detection in the front
of card change interrupt detection.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The bcdUSB value of usb3.1 is 0x0310, we update the condition judgment
to get correct max packet size for usb3.1 dev.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The GetKeyDescriptor() may return NULL when the KeyData is invalid.
For such case, we should go to error handling path rather than assert
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Set the Force Unit Access (FUA) bit in NVMe Write - Command Dword 12 to
ensure write-through behavior.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Change to use a different FILE_GUID to avoid using the
same GUID as the module in IntelFrameworkModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
Change to use a different FILE_GUID to avoid using the
same GUID as the module in IntelFrameworkModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
Count is initially 1 but is assigned to 2 in case PS2_READ_DATA_BYTE.
Though the state machine doesn't go back from PS2_READ_DATA_BYTE to
PS2_READ_BYTE_ONE (not a true bug), force assign Count to 1 to avoid
potential buffer overflow issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
This stack includes:
1. Dxe phase support by:
1) SdMmcPciHcDxe driver to consume PciIo and produce
SdMmcPassThru.
2) SdDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2.
3) EmmcDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2/SSP.
2. Pei phase support
1) SdBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
2) EmmcBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
3) SdMmcPciHcPei driver to produce SdMmcHostController
Ppi.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The 'Reset' function for BlockIO(2) in ScsiDiskDxe should return
EFI_SUCCESS instead of EFI_DEVICE_ERROR when a device does not support
reset feature.
Otherwise, a 'reconnect -r' action when an ISCSI device is attached will
cause system hang.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Remove variables that are declared, assigned but never referenced. This
fixes a warning emitted by GCC when -Wunused-but-set-variable is in effect.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
When there is no bridge before the HPC (hot plug controller),
the issue cannot be seen.
But when there are bridges before the HPC, the PciBus will only
use the value (= <CurrentBusNumber> + <ReservedBusNumber>) as the
sub-ordinary bus number for HPC.
The correct sub-ordinary bus number should be:
<CurrentBusNumber> + <OccupiedBusNumber>(by earlier bridges) +
<ReservedBusNumber>.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Failing to set EFI_MEMORY_UC to MMIO aperture is not a fatal error.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
The "pc" ("pc-i440fx-*") machine types of QEMU don't support extended
config space. Accordingly, OVMF will use the following library instances
in connection with the core PciHostBridgeDxe driver:
BasePciSegmentLibPci [class: PciSegmentLib]
BasePciLibCf8 [class: PciLib]
BasePciCf8Lib [class: PciCf8Lib]
Add a new field to the PCI_ROOT_BRIDGE structure so that
RootBridgeIoCheckParameter() can catch config space offsets above 0xFF on
such old (emulated) platforms.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
... in preparation for the next patch.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Some platform doesn't use CPU(HOST)/Device 1:1 mapping for PCI Bus.
But PCI IO doesn't have interface to tell caller (device driver)
whether the address returned by GetBarAttributes() is HOST address
or device address.
UEFI Spec 2.6 addresses this issue by clarifying the address returned
is HOST address and caller can use AddrTranslationOffset to calculate
the device address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The patch removes the assumption that the resources claimed by root
bridges should not exist. Because resources might have been added:
1. by platform modules either in PEI through resource HOB, or in DXE,
before the PCI host bridge driver runs.
2. Resources claimed by different root bridges may overlap so that
resource adding operation for latter root bridges may fail if
we assume the resource should not exist.
In real world, this patch is to fit OVMF platform needs because
different root bridges in OVMF platform shares the same resources.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
[lersek@redhat.com: intersection-based implementation]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Fix UsbMouseAbsolutePointer driver GetState() interface to return
absolute value instead of relative value.
The driver is ported from UsbMouse driver. The GetState of
SimplePointer protocol returns relative value but the GetState
of AbsolutePointer protocol should return absolute value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
These workhorse functions are part of the BlockIo protocol that
NvmExpressDxe produces. For bulk data access, they are called very
frequently. Their debug messages should be therefore downgraded to
EFI_D_VERBOSE.
In addition, the following DEBUG() warts are cleaned up:
- The function name should be printed with %a / __FUNCTION__, so that
renaming the function, or copying the DEBUG() elsewhere, be reflected in
the debug output automatically. (In fact, after this patch, the DEBUG()
calls become identical.)
- "Lba" is of type UINT64, therefore it should be printed with %Lx, not
%x.
- "OrginalBlocks" and "Blocks" are both UINTN. The only portable way to
print UINTN is to convert it to UINT64 manually, then format it with the
%Lx (or %Lu) conversion specifier.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19763 6f19259b-4bc3-4df7-8a09-765794883524
For some SCSI commands, notably INQUIRY, it's relatively common for
the device to provide less data than we intended to read, and for
this reason EFI_EXT_SCSI_PASS_THRU_SCSI_REQUEST_PACKET makes
InTransferLength and OutTransferLength read-write. Make ATAPI
aware of this.
This makes it possible to handle EFI_NOT_READY always, not just
for read as done in r19685.
I've chosen to use a break statement instead of calling
CheckStatusRegister directly; the break statement reaches a
pre-existing call the CheckStatusRegister function. This
ensures that the assignment to *ByteCount is not missed, and
adds a further sanity check to DRQClear.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19737 6f19259b-4bc3-4df7-8a09-765794883524
SVN r19611 (git commit 7cac240163), "MdeModulePkg/Ide: return correct
status when DRQ is not ready for ATAPI", changed the behavior of
AtaPacketReadWrite(), when DRQReady2() reported an error. The previous
logic had been to:
(a) terminate the transfer loop,
(b) check the status register with CheckStatusRegister(), and determine
AtaPacketReadWrite()'s return code directly from that.
Action (a) had been correct, but action (b) had masked genuine errors.
For example, when DRQReady2() reported EFI_TIMEOUT -- because the BSY bit
had not been cleared within the allotted time --, CheckStatusRegister()
would report EFI_SUCCESS, simply *because* BSY was still set, and the rest
of the status bits could not be evaluated.
SVN r19611 (git commit 7cac240163) intended to fix action (b) by directly
propagating the error code of DRQReady2() from AtaPacketReadWrite(),
eliminating the CheckStatusRegister() call. This was the right thing for
most of the errors reported by DRQReady2() -- timeout, command abort,
other device error --, but there was one exception: the "read" sub-case of
EFI_NOT_READY, which stands for "'read' complete, with less data available
than the requested amount".
Regarding the "write" sub-case of EFI_NOT_READY: the
AtaPacketCommandExecute() function programs the full transfer length into
the IDE device before it calls AtaPacketReadWrite(), and
AtaPacketReadWrite() only uses CylinderLsb and CylinderMsb for "chunking"
(as requested by the device). Therefore the device cannot justifiedly
clear DRQ earlier than seeing the entire data, when writing.
However, when reading from the device, a "short read" is a successful
operation. (The actual read length will be decoded by the higher level
protocols.) And "short reads" had been handled correctly by the logic
before git 7cac240163. Namely, when DRQReady2() returns EFI_NOT_READY, the
BSY bit is already clear, and we can call CheckStatusRegister() to
investigate all the other bits it cares about.
Therefore restore the logic from before git 7cac240163, but only for the
"read" sub-case of EFI_NOT_READY.
This problem was encountered with OVMF running on QEMU's i440fx IDE
emulation. Many thanks to John Snow for analyzing QEMU's behavior, and
pointing out that it adhered to the relevant specs.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: John Snow <jsnow@redhat.com>
Reference: https://github.com/tianocore/edk2/issues/43
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19685 6f19259b-4bc3-4df7-8a09-765794883524
The DRQReady() and DRQReady2() functions only differ in that they poll
different status registers for BSY, ERR, and DRQ: the former looks at the
Status Register (clearing interrupt status), while the latter looks at the
Alternate Status Register (not clearing interrupt status).
They both correctly return a unique status code, EFI_NOT_READY, for the
BSY==0 && ERR==0 && DRQ==0
case; that is, when the device reports "command complete".
However, the functions' leading comments don't explain this case, so it's
easy to miss in callers. Update the comments.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: John Snow <jsnow@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19684 6f19259b-4bc3-4df7-8a09-765794883524
This driver links to PciHostBridgeLib provided by platform/silicon to
produce PciRootBridgeIo and PciHostBridgeResourceAllocation protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19658 6f19259b-4bc3-4df7-8a09-765794883524
As ScsiDisk and ScsiBus driver are used to manage SCSI or ATAPI devices,
the timeout value is updated to 30s to follow ATA/ATAPI spec in which
the device may take up to 30s to respond command.
The change is used to solve device compatibility issue found with a TEAC
DV-W28S-WZ3 slim DVD plus a SONY AccuCORE DVD-R media in which the DVD
spends 8s to response READ_CAPACITY cmd after resetting the host machine.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19612 6f19259b-4bc3-4df7-8a09-765794883524
When executing ATAPI cmd at IDE mode, EFI_SUCCESS may be returned wrongly
with old logic but in fact DRQ is not ready and the transaction doesn't
get executed correctly at this time.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19611 6f19259b-4bc3-4df7-8a09-765794883524
This commit will raise the Tpl to TPL_NOTIFY when adding non-blocking SCSI
I/O requests to the asynchronous task list.
This commit will also raise the Tpl of asynchronous task polling timer to
TPL_NOTIFY.
These changes are made to match the behavior in ScsiDiskDxe driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19455 6f19259b-4bc3-4df7-8a09-765794883524
Raise the Tpl of async SCSI I/O callback function to TPL_NOTIFY to match
the behavior in ScsiDiskDxe driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19454 6f19259b-4bc3-4df7-8a09-765794883524
When reading data from non-blockingly from a CD-ROM logic partition, the
procedure can be shown by the following call stack:
(The write process is similar)
|-------------------|
| DiskIoDxe (logic) |<---Raise Tpl to TPL_CALLBACK
|-------------------|
|
| Sub-task 1 (UnderRun) succeeds
|
| |-----------------| |-----------------| |-----------------|
+--->| PartitionDxe |---->| DiskIoDxe (Phy) |---->| ScsiDiskDxe |
| |-----------------| |-----------------| |-----------------|
|
| Sub-task 2 (OverRun) fails
|
| |-----------------| |-----------------| |-----------------|
+--->| PartitionDxe |---->| DiskIoDxe (Phy) |---->| ScsiDiskDxe |
| |-----------------| |-----------------| |-----------------|
| ^
| |
More subtasks... Wait indefinitely
|
|<---Restore Tpl
|
Completes
In PartitionDxe, if the 'Lba' and 'BufferSize' parameters passed to
function PartitionReadBlocksEx() are invalid, the function will issue a
blocking ReadDisk call (in function ProbeMediaStatusEx()).
In DiskIoDxe, blocking I/O request will wait for all the non-blocking I/O
requests to complete first before sending down the blocking request.
If the Tpl of the async I/O callback in ScsiDiskDxe is TPL_CALLBACK and
Sub-task 1 (UnderRun) succeeds but Sub-task 2 (OverRun) fails with an
invalid parameter, DiskIoDxe will wait indefinitely for the event created
by ScsiDiskDxe of Sub-task 1 to signal.
Hence, this commit will raise the Tpl of async IO callback in ScsiDiskDxe
to TPL_NOTIFY so that the indefinite wait in DiskIoDxe can be avoided.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19452 6f19259b-4bc3-4df7-8a09-765794883524
Some SCSI devices will return EFI_DEVICE_ERROR or EFI_TIMEOUT when the
data length of a SCSI I/O command is too large.
This commit will repeatedly retry sending the SCSI command with a data
length half of its previous value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19451 6f19259b-4bc3-4df7-8a09-765794883524
The functions ScsiRead10CommandEx(), ScsiWrite10CommandEx(),
ScsiRead16CommandEx() and ScsiWrite16CommandEx() in UefiScsiLib will not
signal the event passed from ScsiDiskDxe when error occurs.
In this case, ScsiDiskDxe should close the event passing to these APIs in
UefiScsiLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19449 6f19259b-4bc3-4df7-8a09-765794883524
In ScsiExecuteSCSICommand(), when SCSI devices do not support non-blocking
I/O but an event is passed from caller (UefiScsiLib), the function will
execute the SCSI I/O command in a blocking manner and signal the caller
event when the command completes.
Originally, caller event from UefiScsiLib will be signaled if the SCSI
command fails. UefiScsiLib will continue to signal its caller (BlockIO2
request from ScsiDiskDxe driver), which is not aligned with the UEFI spec
that event will not be signaled when BlockIO2 request returns with error.
This commit will signal ScsiExecuteSCSICommand()'s caller event only when
the SCSI command succeeds.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19447 6f19259b-4bc3-4df7-8a09-765794883524
The functions ScsiDiskWriteBlocks(Ex) in ScsiDiskDxe/ScsiDisk.c do not
check whether the device is allow to be written originally.
This commit will add read-only check to follow the UEFI spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19445 6f19259b-4bc3-4df7-8a09-765794883524
The function ScsiDiskFlushBlocksEx() in ScsiDiskDxe/ScsiDisk.c originally
always returns EFI_SUCCESS, which is not aligned with the UEFI spec.
This commit adds addtional checks to see if the media in the device is
changed or removed. Check for whether the device can be written is also
added. Corresponding status will be returned according to the check
result.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19444 6f19259b-4bc3-4df7-8a09-765794883524
Operands in a bitwise operation have different size. Update code to fix it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19309 6f19259b-4bc3-4df7-8a09-765794883524
In function SignalCallerEvent(), 'Private' and 'TransReq' are dereferenced
before NULL checking.
Since the function assumes that both 'Private' and 'TransReq' passed in
are not NULL pointer, this commit will add an ASSERT to make sure the
above assumption is satisfied.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19266 6f19259b-4bc3-4df7-8a09-765794883524
Add missing braces in module global mControllerDevicePathTemplate.
Initialize ControllerNumber and ContainsControllerNode in
SerialControllerDriverStart() to address warning for potential use
before initialization warning.
Move initialization of local SerialIo earlier in
SerialControllerDriverStart() to address warning for potential use
before initialization warning.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19232 6f19259b-4bc3-4df7-8a09-765794883524
For function ScsiExecuteSCSICommand(), when the 'Event' parameter is not
NULL but the target SCSI device does not support non-blocking I/O, it will
execute a blocking I/O operation instead.
However, after the SCSI operation is done, the 'Event' is not signaled to
inform the caller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19217 6f19259b-4bc3-4df7-8a09-765794883524
PciSioSerialDxe driver can manages UARTs on a SIO chip or a PCI/PCIE
card.
It manages the SIO instance whose last device path node is a ACPI
device path and the HID in the ACPI device path node equals to
EISA_PNP_ID (0x501).
It also manages the PCI IO instance whose class code is 7/0/2 (16550
UART). But when proper value is set to PcdPciSerialParameters, the
driver can also manage non-standard PCI serial cards by matching
the Vendor ID and Device ID specified in PcdPciSerialParameters.
The PCI BAR index, IO/MMIO offset, register stride, clock rate can
also be specified through the same PCD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19179 6f19259b-4bc3-4df7-8a09-765794883524
For a hot plug bridge with device attached, PciBusDxe driver reserves
the resources which equal to the total amount of padding resource
returned from HotPlug->GetResourcePadding() and the actual occupied
resource by the attached device. The behavior is incorrect.
Correct behavior is to reserve the bigger one between the padding
resource and the actual occupied resource.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18719 6f19259b-4bc3-4df7-8a09-765794883524
The resource dumping logic contains a bug which cannot dump the
resource for hot plug controller correctly. The patch fixes this
bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18718 6f19259b-4bc3-4df7-8a09-765794883524
Leif suggested to split the big patch to smaller ones.
This reverts commit 73b7f115c653c807b9d0be97bf516871d8aff7ba.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18717 6f19259b-4bc3-4df7-8a09-765794883524
Add a check for ResourcePaddingDescriptors being a valid pointer in
DumpPpbPaddingResource() to prevent looping on memory not owned by
PciBusDxe. The ResourcePaddingDescriptors is initialized to NULL
when the PCI_IO_DEVICE structure is allocated and remains NULL if
no PCI hot plug controllers are present. This issue is only
observed when DEBUG_CODE() macros are enabled and was introduced
by the following patch:
[edk2] [Patch] MdeModulePkg: Fix a PciBusDxe hot plug bug
SVN revsion 18658
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Kinney Michael <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18696 6f19259b-4bc3-4df7-8a09-765794883524
For a hot plug bridge with device attached, PciBusDxe driver reserves
the resources which equal to the total amount of padding resource
returned from HotPlug->GetResourcePadding() and the actual occupied
resource by the attached device. The behavior is incorrect.
Correct behavior is to reserve the bigger one between the padding
resource and the actual occupied resource.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18658 6f19259b-4bc3-4df7-8a09-765794883524
When looping through all PCI functions, code should not look for functions
1-7 if function 0 is not present or if function 0 indicates the device is
not multifunction. Prior to this fix the code would use stale data in a
buffer to determine if a device is multifunction even if function 0 is not
present. This fixes a code bug and provides very small performance
improvements.
PCI 2.3 Specification states: They [multifunction devices] are also
required to always implement function 0 in the device. Implementing other
functions is optional and may be assigned in any order.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joseph Shifflett <joseph.shifflett@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18574 6f19259b-4bc3-4df7-8a09-765794883524
Some IDE controllers only update ID fields such as sector information on
specific commands such as the DIAG command.
The master/slave device is therefore selected both before and after
sending the DIAG command; otherwise reading the IDE registers yields the
master's ID fields.
(Reza's patch originally *moved* the master/slave selection from after the
DIAG command before it, however Feng asked for the original master/slave
select to be preserved; effectively making the master/slave select
*bracket* the DIAG command. See this subthread:
<http://thread.gmane.org/gmane.comp.bios.tianocore.devel/10545/focus=10550>.)
Cc: Alexander Graf <agraf@suse.de>
Cc: Reza Jelveh <reza.jelveh@tuhh.de>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Reza Jelveh <reza.jelveh@tuhh.de>
[feng.tian@intel.com: see above]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
[lersek@redhat.com: updated commit message]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18529 6f19259b-4bc3-4df7-8a09-765794883524
Certain PCI device may have capability pointing to itself.
Update LocateCapabilityRegBlock() to break when detecting such loop.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18473 6f19259b-4bc3-4df7-8a09-765794883524
The specification of the EFI_EXT_SCSI_PASS_THRU_PROTOCOL.PassThru()
function documents the EFI_BAD_BUFFER_SIZE return status, and the
EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN host adapter
status.
These allow an EFI_EXT_SCSI_PASS_THRU_PROTOCOL implementation to request
higher layers in the stack (in this instance, UefiScsiLib and ScsiDiskDxe)
to break up the transfer into smaller pieces.
These conditions percolate up the stack correctly: the retry loops in
ScsiDiskDxe's ScsiDiskReadSectors() and ScsiDiskWriteSectors() functions
correctly and transparently update the transfer size (ByteCount),
accommodating any shortening requested by lower levels of the stack. After
the loop -- if the request ultimately succeeds -- SectorCount is even
recalculated from the final ByteCount, to see how many sectors the outer
loop should advance.
However, the inner (ie. retry) loops both have the same error: when the
underlying protocols request the transfer to be shortened, the decrease in
transfer size (ie. ByteCount) should immediately be reflected in
SectorCount. Otherwise the sector count encoded in the CDB will exceed the
transfer size, which is a permanent error.
This issue has been witnessed while booting
en_windows_8.1_pro_n_vl_with_update_x86_dvd_6051127.iso
on the 32-bit build of OVMF, from a virtio-scsi CD-ROM:
(1) "cdboot.efi" correctly requested (from far atop) a long read:
Timeout=940000000
CdbLength=10
DataDir=Read
InTransferLength=134215680
OutTransferLength=0
SenseDataLength=108
Cdb: 28 00 00 00 25 DD 00 FF FF 00
^ ^^^^^^^^^^^ ^^^^^
| | |
| | number of 2KB sectors to read,
| | corresponding to 2048 * 65535 = 134215680 bytes
| | (see InTransferLength above)
| |
| LBA to read from
|
READ (10)
(2) In turn, the EFI_EXT_SCSI_PASS_THRU_PROTOCOL.PassThru() function
provided by "OvmfPkg/VirtioScsiDxe/VirtioScsi.c" asked for the request
to be shortened:
InTransferLength=16776704
OutTransferLength=16776704
SenseDataLength=0
HostAdapterStatus=EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN
TargetStatus=0
Status=EFI_BAD_BUFFER_SIZE
(3) Then ScsiDiskReadSectors() in
"MdeModulePkg/Bus/Scsi/ScsiDiskDxe/ScsiDisk.c" retried the request
with correctly shortened transfer length, but incorrectly unchanged
sector count:
Timeout=940000000
CdbLength=10
DataDir=Read
InTransferLength=16776704 <--- updated as requested
OutTransferLength=0
SenseDataLength=108
Cdb: 28 00 00 00 25 DD 00 FF FF 00
^ ^^^^^^^^^^^ ^^^^^
| | |
| | not changed!
| |
| LBA to read from
|
READ (10)
(4) Since 65535 sectors of 2KB each wouldn't fit in a buffer of approx.
16MB, QEMU's virtio-scsi controller unconditionally rejected this
request with VIRTIO_SCSI_S_OVERRUN, which VirtioScsiDxe then mapped
to:
InTransferLength=16776704
OutTransferLength=0
SenseDataLength=0
HostAdapterStatus=EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN
TargetStatus=0
Status=EFI_DEVICE_ERROR
(5) After two more tries of the same, ScsiDiskDxe passed up the error,
which ultimately caused "cdboot.efi" to BSOD.
Many thanks to Larry Cleeton from Microsoft for helping debug
"cdboot.efi".
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18438 6f19259b-4bc3-4df7-8a09-765794883524
Acting specifically upon this error condition from UefiScsiLib (and
ultimately from EFI_EXT_SCSI_PASS_THRU_PROTOCOL.PassThru()) in the
- ScsiDiskRead10(),
- ScsiDiskWrite10(),
- ScsiDiskRead16(),
- ScsiDiskWrite16()
functions allows us to retry these operations from ScsiDiskReadSectors()
and ScsiDiskWriteSectors(), with adjusted transfer sizes, without
investigating further error details like Host Adapter Status, Target
Status, and Sense Data.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18437 6f19259b-4bc3-4df7-8a09-765794883524
The error handling for timeout case is enhanced to remove TDs from
transfer ring. The original code only removed s/w URB, but the h/w
transfer descriptor TDs didn't get removed. It would cause data lost
for data stream peripheral, such as usb-to-serial device, from the
s/w perspective.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18313 6f19259b-4bc3-4df7-8a09-765794883524
In the original code, there exists some mismatches between the real
waiting time and the corresponding timeout comments. For example, the
XHC_GENERIC_TIMEOUT comment says it's 10ms timeout value, but the real
code in fact waits 10s.
So the code is refined to be consistent in code logic and comments.
Note XHC_POLL_DELAY macro also be removed and the polling interval in
XhcWaitOpRegBit() is changed from 1ms to 1us to keep same code style
with other code. It has no real functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18235 6f19259b-4bc3-4df7-8a09-765794883524
EDKII usb stack is using a TPL_CALLBACK timer to monitor async transfer
request and signal event if it's done. As usb enumeration and usb mass
storage block i/o read/write runs on TPL_CALLBACK and TPL_NOTIFY level
respectively, It blocks usb async transfer requests, usually usb mouse
/use kb, getting time to run.
Without this change, user couldn't get usb mouse/kb state in time (will
show a little lag from UI view) when there is other usb transactions, such
as a new usb device inserted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18169 6f19259b-4bc3-4df7-8a09-765794883524
According to the PCI spec, when software writes all-one to BAR for size probing,
the value read back should be 0b1...10...0 after masking the BAR type bits.
But in real world, it's possible that certain device returns 0b0...01...10...0
for MEM64 BAR size probing: some bits in the high 32bit may be 0.
PciBus driver has the code to handle such case. However, it doesn't handle the
case that the high 32bit is totally 0. The patch is to handle the special case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18114 6f19259b-4bc3-4df7-8a09-765794883524
The logic in an if statement in PciIo is too complex and hard to understand
and make VS2015 build failure. The fix simplifies the logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18109 6f19259b-4bc3-4df7-8a09-765794883524
GLOBAL_REMOVE_IF_UNREFERENCED means __declspec(selectany) for MS tool
chain IA32/X64 build.
According to MSDN, "selectany" would tell the compiler that the declared
global data item (variable or object) is a pick-any COMDAT (a packaged
function). At link time, if multiple definitions of a COMDAT are seen,
the linker picks one and discards the rest.
So we have to remove GLOBAL_REMOVE_IF_UNREFERENCED key word from two global
variable's extern definitions of .h file as we have used this keyword in
.c file, otherwise the MS tool chain would pick the definitions in .h file
and treat it as uninitialized data to generate full-0 content for these two
global variables.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18088 6f19259b-4bc3-4df7-8a09-765794883524
The TPer Reset operation would be moved into SecurityPkg/Tcg/
MemoryOverwriteControl/TcgMor.inf module and be triggered at EndOfDxe.
By this way, all encrypted drives which produce EFI_STORAGE_SECURITY_
RPOTOCOL interface would be force reset when MOR is set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17717 6f19259b-4bc3-4df7-8a09-765794883524
Produce this protocol for each namespace at NVMe controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17638 6f19259b-4bc3-4df7-8a09-765794883524
Open NVM_EXPRESS_PASS_THRU rather than PCI_IO to create parent-child
relationship.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17636 6f19259b-4bc3-4df7-8a09-765794883524
The initialization of Cc.Iosqes and Cc.Iocqes should not be removed
before any I/O operation as it would impact Qemu-NVMe functionality
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17559 6f19259b-4bc3-4df7-8a09-765794883524
Follow IDE BUS Master spec to ensure the PRDT table not cross 64k
boundary in memory.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17552 6f19259b-4bc3-4df7-8a09-765794883524
LocatePciExpressCapabilityRegBlock () doesn't check the return status of Pci.Read().
Certain platform's PciRootBridge.Pci.Read() doesn't support PCIE access causing the CapabilityEntry not updated.
If the uninitialized CapabilityEntry equals to a big enough initial value, the while-loop will never end.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17513 6f19259b-4bc3-4df7-8a09-765794883524
A previous incorrect check-in adds the IsaBusDxe driver to <Root>/Bus directory.
The patch fixes it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17506 6f19259b-4bc3-4df7-8a09-765794883524
The original code hard-codes block size to 512. But after ATA 7 spec,
the non-512 block size is also supported. The code is updated to
dynamically calculate the block size according to IDENTIFY data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17495 6f19259b-4bc3-4df7-8a09-765794883524
It's to follow the PI spec 1.4.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jie Lin <jie.lin@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17367 6f19259b-4bc3-4df7-8a09-765794883524
This patch produces a EFI_NVM_EXPRESS_PASS_THRU protocol instance
on device handle to provide upper user a way to send cmd to NVMe
device.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17286 6f19259b-4bc3-4df7-8a09-765794883524
The changes in ScsiDisk include:
1. Add UFS disk info support.
2. Remove the wrong block size calculation.
3. Get sense data for TEST_UNIT_READY cmd immediately rather than sending a REQUEST_SENSE cmd again.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17247 6f19259b-4bc3-4df7-8a09-765794883524
It includes 4 drivers:
1. UfsPassThruDxe, which is a UEFI driver and consumes EFI_UFS_HOST_CONTROLLER_PROTOCOL and produces EFI_EXT_SCSI_PASS_THRU_PROTOCOL
2. UfsPciHcDxe, which is specific for pci-based UFS HC implementation and is a UEFI driver to produce EFI_UFS_HOST_CONTROLLER_PROTOCOL.
3. UfsBlockIoPei, which is a PEI driver and consumes EFI_UFS_HOST_CONTROLLER_PPI and produces EFI_PEI_VIRTUAL_BLOCK_IO_PPI.
4. UfsPciHcPei, which is specific for pci-based UFS HC implementation and is a PEI driver to produce EFI_UFS_HOST_CONTROLLER_PPI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17246 6f19259b-4bc3-4df7-8a09-765794883524
The number of the Prp lists and the number of the entries in last Prp list may be calculated wrongly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Baban Devkate <baban.devkate@seagate.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17208 6f19259b-4bc3-4df7-8a09-765794883524
Media->IoAlign field of BlockIo protocol instance installed by this driver should be set to the value of ScsiIo->IoAlign.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17195 6f19259b-4bc3-4df7-8a09-765794883524
The restriction of UsbHc2.SyncInterruptTransfer() on interrupt transfer direction is removed. This interface could support Interrupt IN/OUT now.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17041 6f19259b-4bc3-4df7-8a09-765794883524
Setting a bit in the PxSACT register for a command in the command list indicates
to the controller that the command list slot contains a native queued command (NCQ).
This can cause problems with some controllers (one such controller is the Marvell 9128).
Since NCQ commands are not used, don't set the PxACT register for commands issued.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chris Ruffin <chris.ruffin@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16536 6f19259b-4bc3-4df7-8a09-765794883524
- Fix EFI_IPv4_ADDRESS usages to use a macro to copy the structure
instead of direct assignment, to avoid runtime alignment errors.
- Fix a EFI_INPUT_KEY usage in TerminalDxe to use CopyMem() to copy the
structure instead of direct assignment, to avoid runtime alignment error.
- Delete excess local variables that are initialized but otherwise unused.
- CompilerIntrinsicsLib library now imported for AARCH64, as well as ARM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Randy Pawell <randy_pawell@hp.com>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16471 6f19259b-4bc3-4df7-8a09-765794883524
Per AHCI 1.1 spec, AE bit of GHC register is read-only if CAP.SAM is 1
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16321 6f19259b-4bc3-4df7-8a09-765794883524
DiskIoDxe: Fix ReadDiskEx and WriteDiskEx to not modify the user’s buffer when the BufferSize is 0.
DiskIoDxe: Fix ReadDiskEx and WriteDiskEx hang issue when the submitted blockio2 task is completed before submitting another blockio2 task.
DiskIoDxe: Fix FlushEx to free the flush task item in callback (memory leak issue).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16215 6f19259b-4bc3-4df7-8a09-765794883524
1. Add delay after set device address and get configuration descriptor.
2. Sync the change at R15876 in XhciDxe to do not access transfer ring when endpoint is isochronous type or control type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16105 6f19259b-4bc3-4df7-8a09-765794883524
1. Module UNI and Package UNI files are not DOS format. Convert them to DOS format.
2. Remove unused SectionExtractionDxeModStrs.uni and SectionExtractionPeiModStrs.uni
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16044 6f19259b-4bc3-4df7-8a09-765794883524
2. Add MODULE_UNI_FILE file that contains the localized Abstract and Description of a module.
a. Addresses an information gap between INF files and the UEFI Distribution Packaging Specification XML schema
b. There will be an associated update to UPT in BaseTools to consume MODULE_UNI_FILE and associated UNI file during UDP creation that performs the INF -> XML conversion.
c. There will be an associated update to UPT in BaseTools to produce MODULE_UNI_FILE and associated UNI file during UDP installation that performs the XML -> INF conversion.
3. Add Module Extra UNI file that provides the localized Name of a module.
a. [UserExtensions.TianoCore."ExtraFiles"] provides an easy method for a module to specify extra files not listed in [Sources] or [Binaries] sections to be added to a UDP without having to list the files in the UPT package information data file.
b. There will be an associated update to UPT in BaseTools to package up files listed in [UserExtensions.TianoCore."ExtraFiles"] during UDP creation.
c. UNI file contains localized name of a module to go along with the localized Abstract and Description from the MODULE_UNI_FILE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15963 6f19259b-4bc3-4df7-8a09-765794883524
1. Usage information in INF file comment blocks are either incomplete or incorrect.
This includes usage information for Protocols/PPIs/GUIDs/PCDs/HOBs/Events/BootModes.
The syntax for usage information in comment blocks is defined in the EDK II Module Information (INF) Specification
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15962 6f19259b-4bc3-4df7-8a09-765794883524
creation) of PciIoDevice->DevicePath. The bug can be triggered when
PciBusDxe is built into OVMF, with qemu/KVM device assignment of
a PCI-express device on the default 440FX machine type. OVMF
correctly discovers that the device is PCIe and begins probing
extended configuration space for the device. The root bridge
has no way to access extended config space and correctly errors,
sending us into the error reporting chain seen below. It's
possible that this error path could also be reproduced on physical
hardware when a PCI-to-PCIe bridge is present.
GatherDeviceInfo() | GatherPpbInfo() | GatherP2CInfo() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
CreatePciIoDevice() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
AllocateZeroPool()
LocateCapabilityRegBlock() [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoDevice->IsPciExp = TRUE
LocatePciExpressCapabilityRegBlock() [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoConfigRead() via funcptr [MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c]
RootBridgeIoPciRead() via funcptr [PcAtChipsetPkg/PciHostBridgeDxe/PciRootBridgeIo.c]
FAILS
REPORT_STATUS_CODE_WITH_DEVICE_PATH() [MdePkg/Include/Library/ReportStatusCodeLib.h]
ReportStatusCodeWithDevicePath() [MdeModulePkg/Library/DxeReportStatusCodeLib/ReportStatusCodeLib.c]
ASSERT (DevicePath != NULL) <--+
CreatePciDevicePath() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
sets PciIoDevice->DevicePath ----------+
In English:
- CreatePciIoDevice() allocates a zeroed out PCI_IO_DEVICE structure.
- PciIoConfigRead() tries to access the (extended) config space, and
fails.
- PciIoConfigRead() wants to report a status code (read error) for the
device path.
- Unfortuantely, PciIoDevice->DevicePath is still NULL at that point.
- The ASSERT() in ReportStatusCodeWithDevicePath() fires.
Fix it by moving CreatePciDevicePath() into CreatePciIoDevice(),
allowing PciIoDevice->DevicePath to be initialized before we
begin probing the device capabilities:
GatherDeviceInfo() | GatherPpbInfo() | GatherP2CInfo() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
CreatePciIoDevice() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
AllocateZeroPool()
CreatePciDevicePath() [MdeModulePkg/Bus/Pci/PciBusDxe/PciEnumeratorSupport.c]
sets PciIoDevice->DevicePath -----------+
LocateCapabilityRegBlock() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoDevice->IsPciExp = TRUE |
LocatePciExpressCapabilityRegBlock() | [MdeModulePkg/Bus/Pci/PciBusDxe/PciCommand.c]
PciIoConfigRead() via funcptr | [MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c]
RootBridgeIoPciRead() via funcptr | [PcAtChipsetPkg/PciHostBridgeDxe/PciRootBridgeIo.c]
FAILS |
REPORT_STATUS_CODE_WITH_DEVICE_PATH() | [MdePkg/Include/Library/ReportStatusCodeLib.h]
ReportStatusCodeWithDevicePath() | [MdeModulePkg/Library/DxeReportStatusCodeLib/ReportStatusCodeLib.c]
ASSERT (DevicePath != NULL) <-----+
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15567 6f19259b-4bc3-4df7-8a09-765794883524
Besides this, the patch also fixed:
1) Wrong return value in SenseDataLength field of packet field of EFI_EXT_SCSI_PASS_THRU protocol, it should reflect real sense data length we got.
2) Wrong logic in ScsiDiskRequestSenseKeys that the logic makes SenseData pointer unaligned compared with BlockIo.Media.IoAlign field.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian, Feng <feng.tian@intel.com>
Reviewed-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Fu, Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15491 6f19259b-4bc3-4df7-8a09-765794883524
If the structure layout in UsbBusPei is changed, then the UsbBotPei will not work.
1. As the maximum number of endpoints is 16, use UINT16 type rather than UINT8 for DataToggle.
2. DataToggle needs to be reset to 0 when endpoint stall is cleared, do it in PeiUsbControlTransfer().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15185 6f19259b-4bc3-4df7-8a09-765794883524
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Leahy Leroy P <leroy.p.leahy@intel.com>
Reviewed-by: Lin Jie <jie.lin@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14952 6f19259b-4bc3-4df7-8a09-765794883524
Platforms such as Xen already enumerates PCI bridges and devices. Use
this PCD to control EDK2 behavior.
PcdPciDisableBusEnumeration is placed under [PcdsFixedAtBuild,
PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx], so that it is
possible to alter it during runtime.
The default setting of this PCD is false (allow full PCI enumeration) to
preserve the same behavior before this change.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14940 6f19259b-4bc3-4df7-8a09-765794883524
1.Port reset process may not be proper for some vendor's SS hubs. If the corresponding port shows the reset has been done by C_RESET bit we have to skip the whole reset process for attached devices.
2.Clean C_BH_RESET bit immediately to avoid usb timer entering too many times when 5 tiers hubs are connected.
3.Stop checking URB if there is an error happened.
4.Better error handling for fast hot-plug.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14889 6f19259b-4bc3-4df7-8a09-765794883524
1) The Queue size field in create I/O submission/completion queue cmds is 0-based. the current code is 1-based.
2) a typo on allocated memory page size. it's inconsistent that some places is using 4 pages, but a place is using 6 pages.
3) a typo on PRP/SGL mechanism judgment. should directly use Psdt field rather than Opc field.
4) some platforms may not support UINT64 width access on MMIO register. Fix it to use two 32-bit width access.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Kinney Michael <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14657 6f19259b-4bc3-4df7-8a09-765794883524
the PCI Bus driver through the function call NotifyPhase().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14483 6f19259b-4bc3-4df7-8a09-765794883524
The r14226 check-in indeed has memory leak in allocated "Child" pointer. UsbBusDriverBindingStop() may dereference this pointer and may bring exception on invalid memory access
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14251 6f19259b-4bc3-4df7-8a09-765794883524
1.enlarge the recovery time from 10ms to 20ms after port reset to make set address request success for better device compatibility.
2.another enhancement is to use RESET_C bit rather than RESET bit to judge if hub reset port operation is done.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14227 6f19259b-4bc3-4df7-8a09-765794883524
1.Fix the bug in interface parser logic for usb camera device. Reserve device address if the device doesn’t get disconnected.
2.Some usb 1.1 devices require the context evaluation immediately with actual max packet size after detecting the device max packet size.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14226 6f19259b-4bc3-4df7-8a09-765794883524
This way is used to avoid that the subsequent operations are treated as failure if the last operation is wrong.
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Sun Rui <rui.sun@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13663 6f19259b-4bc3-4df7-8a09-765794883524
Clean up the code to remove unnecessary NotifyHandle in the private data structure.
Signed-off-by: Ruiyu Ni<ruiyu.ni@intel.com>
Reviewed-by: Elvin Li<elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13565 6f19259b-4bc3-4df7-8a09-765794883524
Enhance ConSplitter to register hot keys for new connected consoles.
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hot Tian <hot.tian@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13358 6f19259b-4bc3-4df7-8a09-765794883524
Signed-off-by: Sun Rui <rui.sun@intel.com>
Reviewed-by: Fan Jeff <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13189 6f19259b-4bc3-4df7-8a09-765794883524
Laszlo Ersek
Star Zeng
Hao Wu
Ruiyu Ni
Bi, Dandan
Ard Biesheuvel
Dandan Bi
Jiewen Yao
Suman Prakash
Feng Tian
Thomas Huth
Haojian Zhuang
Marcin Wojtas
Gary Lin
Giri P Mudusuru
Evgeny Yakovlev
Joe Zhou
Jan D?bro?
Cinnamon Shia
Darbin Reyes
Ma, Maurice
Qiu, Shumin
Alcantara, Paulo
Paolo Bonzini
Samer El-Haj-Mahmoud
Jordan Justen
Michael Kinney
Anbazhagan, Baraneedharan
Joseph Shifflett
Reza Jelveh
Liming Gao
Olivier Martin
Chris Ruffin
Randy Pawell
Samer El-Haj-Mahmoud
jaben carsey
Nikolai Saoukh
Elvin Li
Chen Fan
Eric Dong
Alex Williamson
Tian, Hot
Wei Liu
Sergey Isakov
erictian
niruiyu
ydong10
li-elvin
lzeng14
qianouyang
rsun3